Manual Nikon ACULON (page 43 of 64) (English, French, Portuguese, Spanish)

733826

Zoom out

Zoom in

1/64

Mesure

Attention — L'emploi de commandes, réglages ou

performances de procédure autres que ceux

spécifiés dans ce manuel peut entraîner une

exposition à des rayonnements dangereux.

1. Installez une pile dans le logement prévu à cet

effet. (Reportez-vous à la section « Insérer et

remplacer la pile »).

2. Correction dioptrique

Réglez la correction dioptrique pour obtenir une

image nette sur l'écran ACL.

Tournez d'abord la bague de réglage dioptrique dans

le sens antihoraire jusqu'à ce qu'elle soit totalement

en butée. Ensuite, mettez l'appareil sous tension

pour activer l'écran ACL quand vous regardez dans le

Télémètre Laser Nikon. Tournez la bague de réglage

dioptrique dans le sens horaire jusqu'à ce que

l'affichage soit net.

Si la correction dioptrique ne correspond pas à votre

vue, vous aurez des difficultés à effectuer la mise au

point sur le sujet.

3. Mesure

Avant de prendre les mesures, veillez à confirmer les

paramètres du dispositif.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Immédiatement après

la mise sous tension.

(initialisation)

En veille. Cible visée.

3. Appuyez

une fois sur le bouton POWER ON/Mesure pour prendre

une mesure unique.

En maintenant le bouton enfoncé, vous pourrez prendre une

mesure continue jusqu'à environ 20 secondes.

Mesure en cours.

Pendant la mesure, l'affichage interne affiche les témoins

clignotants « distance » ou « échec de la mesure ». (Le signe de

rayonnement laser clignote lors de la prise de mesure).

Échec de la mesure ou

mesure de distance

impossible.

Affiche les

résultats mesurés.

(Cible 1)

Affiche les résultats

mesurés. (Cible 2)

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



5. Une fois la mesure terminée, les résultats mesurés s'affichent

pendant environ 8 secondes environ, puis l'appareil se met hors

tension.

Si vous appuyez sur le bouton

POWER ON/Mesure

lors

du démarrage (pendant que l'écran interne est éclairé), une autre

mesure unique s'initie.

1. Mettez l'appareil sous tension

(Vérifiez que l'écran interne est allumé)

2. Visez la cible.

Positionnez la cible

au centre du réticule.

(Arrêt automatique après environ

8 secondes de non-utilisation.)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon ACULON in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 4,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nikon ACULON

Nikon ACULON User Manual - German, Dutch, Danish, Italian, Polish, Swedish, Norwegian, Finnish - 184 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon ACULON Manual

Product: