Manual Nikon ACULON (page 148 of 184) (German, Dutch, Danish, Italian, Polish, Swedish, Norwegian, Finnish)

733826

148

Zoom out

Zoom in

1/184

148

Měření

Používání ovládacích prvků nebo nastavení nebo

vykonávání postupů jinak, než jsou uvedeny v

této příručce, může mít za následek vystavení se

nebezpečnému záření.

1. Instalujte baterii do komory baterií. (Viz "Vložení

a výměna baterie")

2. Dioptrické nastavení

Nastavte dioptrii pro získání jasného obrazu na LCD.

Nejdříve otáčejte kroužkem dioptrického nastavení

proti směru hodinových ručiček až se úplně zastaví.

Potom zapněte napájení pro aktivaci LCD, když

se díváte přes laserový dálkoměr Nikon. Otáčejte

kroužkem dioptrického nastavení ve směru

hodinových ručiček až se displej zaostří.

Pokud není dioptrie nastavena tak, aby odpovídala

vašemu zraku, možná nebudete schopen správně

zaostřit svůj předmět.

3. Měření

Před měřením zkontrolujte nastavení jednotek.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



3. Stiskem tlačítka POWER ON/Measurement (vypínač/měření)

spustíte jedno měření.

Podržení stlačeného tlačítka umožňuje trvalé měření po dobu až

cca 20 sekund.

Měření.

4. Na vnitřním displeji se bude během měření střídavě zobrazovat

ukazatel “vzdálenost” a “nezdar měření”. (Znak laserového záření bliká.)

Porucha měření nebo

neschopen změřit

vzdálenost.

Zobrazí

naměřenou

hodnotu. (Cíl 1)

Zobrazí naměřenou

hodnotu. (Cíl 2)

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by. Target focusing.

2. Aim at the target

3. Press POWER button once to start

continuous measurement for 8 seconds.

(Single measurement mode is not

available with this laser rangefinder.)

Measuring.

4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.

(Laser irradiation mark is blinking.)

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

5. After continuous measurement, the measured results are displayed for 8 seconds, then power

turns off.

If you press the POWER button during power-on (while the internal display is lit), another

8-second measurement starts.



5. Po ukončení měření se na zhruba 8 sekund zobrazí naměřené

výsledky. Poté se přístroj vypne. Pokud na zapnutém přístroji

(při zapnutém vnitřním displeji) stisknete tlačítko POWER ON/

Measurement (vypínač/měření), spustí se další měření.

Okamžitě po zapnutí.

(Inicializace)

Pohotovostní

režim.

Zamíření na cíl.

1. Zapněte napájení (zkontrolujte,

zda je vnitřní displej zapnutý).

2. Zamiřte na cíl.

Umístěte cíl do

středu nitkového

kříže.

(Automatické vypnutí přibližně

po 8 sekundách nečinnosti.)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon ACULON in the language / languages: German, Dutch, Danish, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 10,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nikon ACULON

Nikon ACULON User Manual - English, French, Portuguese, Spanish - 64 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon ACULON Manual

Product: