619208

Niko 100-78010 Manual

8
Zoom out
Zoom in
Previous page
1/12
Next page
1XX-7801X
8
EN nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu PM1XX-7801XR13375
8. NIKO UNTERSTÜTZUNG
Bei Zweifel oder falls Sie bei einem eventuellen Defekt des Produkts noch Fragen bezüglich des Umtausches
haben, dann nehmen Sie bitte Kontakt auf mit dem Kundendienst von Niko (Belgien: +32 3 778 90 80) oder
wenden Sie sich an Ihren Großhändler. Kontaktdaten und weitere Informationen erhalten Sie im Internet unter
www.niko.eu in der Rubrik “Unterstützung und Beratung”.
9. GARANTIEBEDINGUNGEN
- Der Garantiezeitraum beträgt vier Jahre ab Lieferdatum. Als Lieferdatum gilt das Rechnungsdatum
zum Zeitpunkt des Kaufs durch den Endverbraucher. Falls keine Rechnung mehr vorhanden ist, gilt das
Produktionsdatum.
- Der Endverbraucher ist verpflichtet, Niko schriftlich über einen Produktmangel innerhalb von zwei Monaten
nach dessen Feststellung zu informieren.
- Im Falle eines Mangels hat der Endverbraucher nur Recht auf kostenlose Reparatur oder Ersatz des Produkts.
Eine Entscheidung darüber obliegt allein Niko.
- Niko ist nicht für Mängel oder Schäden verantwortlich, die durch fehlerhafte Installation, nicht
bestimmungsgemäßen oder unsachgemäßen Gebrauch, durch falsche Bedienung, Anpassen/Ändern des
Produktes, infolge von unsachgemäßer Wartung entgegen den Wartungsvorschriften oder die sich aus
äußeren Umständen, wie beispielsweise infolge Feuchtigkeit oder Überspannung, ergeben.
- Zwingende Vorschriften der nationalen Gesetzgebung bezüglich des Verkaufs von Konsumgütern und zum
Verbraucherschutz haben vor den obigen Bestimmungen Vorrang in den Ländern, in denen Niko direkt oder
über seine Neben- oder Tochtergesellschaften, Filialen, Vertriebsstellen, Agenten oder über feste Vertreter
verkauft.
Read the complete manual before carrying out the installation and activating the system. Keep the
manual for future reference.
1. DESCRIPTION
The 180° flush-mounting motion detector is an electronic motion-detecting switch that is intended for
indoor use only. The motion detector switches on the load (lighting) if movement of a heat source is detected
and if the daylight level is lower than the preset lux value. The device detects movement with the aid of
Passive Infrared technology (PIR).
The device (actuator + sensor) is supplied on a pre-assembled metal base (45 x 45). The flush surround plate
must be ordered separately.
2. INSTALLATION
2.1. Connection
Danger: Disconnect all power before installing the motion detector. Do not connect the device to the mains
voltage until installation has been completed (including the flush surround plate).
A. One lighting circuit with one detection point
Connect the motion detector and the load according to the following wiring diagram:
L
N
230 Vac
B. One lighting circuit with several detection points
In this case, a master and a slave must be assigned. You can connect a maximum of eight slaves to one master.
Connect the slave(s) to the master according to the wiring diagram below:
L
N
230 Vac
Slave Master
C. Use of an external push button or switch
You connect an external push button or switch to the motion detector if you must also be able to control the
device manually. You can connect the push button or switch to either the master or to a slave.
Follow the wiring diagram below to connect the push button or switch:
L
N
230 Vac
2.2. Mounting
Tip: Do not install the motion detector in direct sunlight or in the vicinity of heat sources or air currents (ventilation
or air conditioning). This can activate the motion detector unnecessarily.
Tip: Mount the motion detector (master) at the location where the light intensity (lux value) is best measured.
Mount the motion detector in a flush-mounting box with a flush-mounting depth of minimum 40mm at a height
between 0.8 and 1.2 m.
3. SETTINGS
Under the hinged cover at the front of the motion detector, there are two potentiometers for setting the following
four parameters:
light sensitivity (± 10 – 1000 lux)
switch-off delay (± 1 – 30 min)
slave
test mode
1
2
3
4
1
2
3 4
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Niko 100-78010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Niko 100-78010 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info