776299
95
Zoom out
Zoom in
Previous page
1/99
Next page
SECTION VI THEORY OF OPERATION
Utrecht
- 94 - Ref 001
- Disconnect the modem from the PC and connect it to the instrument with special
RS232 cable (see chapter 4 for connection diagram) , both must be in the power off
state (switched off).
When the modem is being configured with Power Link the following settings are executed:
- disable PIN for GSM modem (AT+CPIN=XXXX and AT+CLCK=”SC”,1,XXXX,
- enable automatic answering (AT&D0),
- set automatic answering after 2 RINGS (ATS0=2),
- set ECHO answering to OFF (ATE0),
- disable “Wait for dial tone” option (ATX0),
- set PORT baud rate for standard (analog) modem,
- save parameters (AT&W),
- activate saved parameters (ATZ).
When the third party modem requires different settings we recommend using the Hyper
Terminal program for modem configuration. It is part of standard Windows setup. You can
find it on your PC: Programs / Accessories / Communications / Hyper Terminal.
3.4. Instrument configuration for modem communication
Instrument should be configured before communicating with the PC via modem
communication. The following procedure is required:
- Modem should be connected to the instrument.
- Switch the instrument on.
- Switch the modem on.
- In SYSTEM menu select SER.PORT RATE / GSM/SMS PARAM. / DISABLED for
Standard (analog) modem.
- In SYSTEM menu select SER.PORT RATE / GSM/SMS PARAM. / ENABLED for
GSM modem (it enables sending of SMS messages).
ENABLE PASSW.
GSM/SMS PARAM. => ENABLED >> DISABLE
DATE/TIME CPIN : XXXX
LANGUAGE DEST:
SYSTEM REINIT. USERID:
CLR.REC.MEM. SEND TEST MESSAGE
- Enter PIN code using cursor keys: UP/DOWN to increment/decrement selected
number and LEFT/RIGHT to select previous or next number (for GSM modem).
- Press ENTER to confirm entry or ESC to discard it.
I you want to disable sending of SMS messages (when using GSM modem) you should
set GSM/SMS PARAM. to DISABLED and set SERIAL PORT RATE to 9600.
If a GSM modem is used on the PC side and Standard modem is used on the instrument
side, baud rate of 9600 bps must be used for the standard modem.
95


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nieaf-Smitt PQA 6600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nieaf-Smitt PQA 6600 in the language / languages: English as an attachment in your email.

The manual is 1.72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info