641176

Niagara B264 Standalone Encoder Manual

102
Zoom out
Zoom in
Previous page
1/120
Next page
102
720p to Ethernet 1, 2 and ASI: This template configures both encoders to run from
HD-SDI 720p inputs (Encoder 1 from Video 1, Encoder 2 from Video 2). Encoders are
routed to individual multicasts on both Ethernet ports, and as an MPTS to both ASI Ports.
1080i to Ethernet 1, 2 and ASI: This template configures both encoders to run from
HD-SDI 1080i inputs (Encoder 1 from Video 1, Encoder 2 from Video 2). Encoders are
routed to individual multicasts on both Ethernet ports, and as an MPTS to both ASI Ports.
1080i + SD from Video 1 to Eth 1, 2, ASI: This template configures both encoders to
run from an HD-SDI 1080i input connected to Video 1. Encoder 1 runs at full resolution,
Encoder 2 downscales the content to SD. Encoders are routed to individual multicasts on
both Ethernet ports, and as an MPTS to both ASI Ports.
Clear Current Configuration Button
The Clear Current Configuration button clears all the configured ports and streams as follows:
All ASI Ports are set to manual configuration, 20 Mb/s, 188-byte packets.
All Encoders are stopped and configured with a default set of parameters.
All IP Outputs are deleted.
All Connections are removed.
The Test Packet Generators are disabled.
The button does not affect the following areas:
The settings in the Network tab are not changed.
The settings in the Admin General tab are not changed.
Saved configurations are not modified in any way.
Dashboard™ will take a few seconds to reload (longer if you are accessing over a wide-area
network), but the actual configuration in the B264 is virtually instantaneous. The Status
Message Area will indicate the result of the operation.
Admin Test Packet Generator Tab
The B264 includes two Test Packet Generators (TPG) that are capable of generating a
configurable constant bit rate sequence of MPEG-2 Transport Packets with very strict timing.
The TPGs are considered a source (input), and are available to be connected to any output. The
user interface for the TPGs includes a current status table, which reports the current
configuration of the generators.
To configure one of the TPGs, click on the Edit button on its row. The following configuration
parameters are displayed:
… 102 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Niagara B264 Standalone Encoder at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Niagara B264 Standalone Encoder in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Niagara B264 Standalone Encoder

Niagara B264 Standalone Encoder Quick start guide - English - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info