698585
24
Zoom out
Zoom in
Previous page
1/50
Next page
Screen Saver
Turn on the screen saver function to shut down the screen after 30 seconds without any interaction.
With the screen off, recording will continue as normal. Touch the display to re-open the screen.
You can also choose for the Screen Saver to show your current speed (GPS signal required).
Options: On and Off and Speed Display
Default: Off
Alerts
Turn On/Off the ascending/descending beeps that sound when a recording starts/stops, the alarm
that sounds when battery is low or there is an SD Card error, and the chime that sounds when a
file is protected.
Options: On and Off
Default: Off
Recording History
In some territories, there are laws prohibiting the amount of footage your Dash Cam should
hold. The default setting is ‘Maximum’, where your Dash Cam records and stores videos without
restriction.
If ‘Minimum’ is selected you will first be asked to Format (wipe) your SD Card; be sure to back
up any files you wish to keep before doing this. If you choose not to Format the SD Card, no action
is taken and the function will not be activated.
Once the SD Card has been formatted, the file recording length will be automatically set to
1 minute. The Dash Cam will now be limited to storing only 4 unprotected files at any one time.
When a new file is recorded it will overwrite the oldest file, keeping the number of stored files
at the maximum of 4.
As protected files (i.e. recordings of incidents) cannot be overwritten, these do not count
towards the 4 file maximum, and are stored to the capacity of the SD Card.
When Recording History is turned On, Time Lapse will be turned Off.
Options: Maximum and Minimum
Default: Maximum
Parking Mode
When Parking Mode has been turned on, the Dash Cam enters standby mode when the 12Vdc
supply has been turned OFF (typically removing your ignition key).
The Dash Cam will also enter standby mode if no physical movement is detected for 5 minutes,
this is designed to allow use of a permanent 12Vdc supply, i.e hard-wire kit.
Should physical movement of the vehicle be detected, the Dash Cam will power on and start
recording a 30 second protected video. If no further physical movement is detected then the
Dash Cam will return to standby mode, if physical movement is detected subsequently, then the
camera will continue to record normally, i.e. driving once more.
Options: On and Off
Default: Off
13
14
15
Setup Settings
9
10
11
12
6
7
8
24
Video Settings (cont.)
16
Speed Stamp
Turn On/Off the speed stamp shown on recorded files.
Options: On and Off
Default: On
GPS Stamp
Turn On/Off the location data stamp shown on recorded files.
Options: On and Off
Default: On
Model Stamp
Turn On/Off the Dash Cam model stamp shown on recorded files.
Options: On and Off
Default: On
Dual Files
When recording, both a high and low quality video are saved. The smaller file size of the low quality
video means it is quicker to transfer and edit within the app. If a Rear-Cam is attached, and Dual
Files is switched ON, High and Low resolution files will be saved for the Rear view as well, giving you a
total of 4 files (Front High, Front Low, Rear High, Rear Low)
Note: Recording both high and low resolution versions will take up more space on the memory card.
Options: On and Off
Default: On
Time Lapse
Time Lapse recording is a technique whereby the frequency at which file frames are captured (frame
rate) is lower than that used when playing back the recording. Time Lapse recording can be considered
the opposite of slow motion, as when the recording is played back time appears to be moving faster.
For example, a recording taken over three minutes would be played back as a 30 second movie.
Notes: - When Time Lapse is turned On, Recording History will be turned Off.
- Time lapse is considered as a leisure activity setting and not for use in order to collect evidence
in the case of an incident. Time Lapse should be turned off for normal driving conditions.
Options: 3 minutes, 30 minutes, Off
Default: Off
Number Plate
Input your vehicle’s number plate to add a number plate stamp to your recordings.
Default: Off
G Sensor
Turn off or adjust the sensitivity of the internal G Sensor. The G Sensor detects forces which will
protect the current recording in the event of a collision. The higher the G Sensor sensitivity, the less
force will be needed to trigger automatic file protection.
Options: Off, Low, Medium, High
Default: Medium
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nextbase 522GW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nextbase 522GW in the language / languages: English as an attachment in your email.

The manual is 81,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nextbase 522GW

Nextbase 522GW User Manual - German - 50 pages

Nextbase 522GW User Manual - Dutch - 50 pages

Nextbase 522GW User Manual - French - 50 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info