22060

Newpol XD900IXDG Manual

14
Zoom out
Zoom in
Previous page
1/80
Next page
GB
12
Options
(Note: the various options must be selected before initiating the wash cycle)
• Delayed start : time delays for the initiation of the wash cycle can be set ranging from 1 to 16 hours.
On the display, the delay period that was selected will be shown. The LED display will be blinking during the
entire delay period.
The selection of this setting option is confirmed when the number of the pre -selected programme appears
on the display.
• Half load : when choosing this wash cycle option, the following indication will appear on the display:
(¯=wash superior basket,_=wash inferior basket). The corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme appears
on the display.
• Pre-wash cancel : This option is only available for programmes that include a pre-wash.
When pressing the button, the corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme appears
on the display.
• Drying : this programme option is carried out automatically by the programmes in whose cycle it is
included (see programme table). To modify the dryer setting, the drying button must be pressed before
initiating the chosen programme. On the display, the following information will appear: AO = no drying; A1=
Drying 20’; A2 = Drying 35’; A3 = Drying 45’.
The corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre -selected programme appears
on the display.
• Note: In the models without the drying ventilator, this option is to be considered as waiting time at the end
of the cycle.
• Description of Start/Stop/Pause button
• It initiates the wash programme cycle (the buzzer sound indicates that the cycle has started).
• When you turn on the machine, using the ON/OFF button, the display indicates the number of the last
program that has been carried out. In cases where the previous program has not yet finished, the display
will flash the number of this program. In order to re-start it you must simply press the “START” button ,
the remaining time that is necessary in order to finish the cycle will appear automatically on the display.
(Situations such as this will occur each time that you open the machine when it is carrying out a program).
• If pressed during the wash for less than 5” the machine will pause, the number of the program will be seen
flashing on the display, (in this case it is possible to add or remove dishes etc.)
In order to proceed with the washing program, close the door and press the button again.
• Programme settings by mistake (change programme)
• Reset by using the start/stop/pause button : keep the button pressed until the buzzer stops beeping (it
produces a series of beeps).
• Repeat the select programme operation.
Note: If the programme has been initiated and has run beyond the water fill phase, the display indicates
“ “, Then, the appliance will discharge all water, and (after a prolonged buzzer sound) the display will
indicate the pre-selected programme setting.
Now, the appliance is ready for a new setting.
• Note: Once you have opened the door, always press the Start button in order to restart the dishwasher.
• Activation / Elimination of the buzzer
b0 = Buzzer DEACTIVATED
b1 = Buzzer ACTIVATED
In order to access the setting of the BUZZER, keep the PROGRAM button pressed down when you
turn on the machine. The current setting “b1” will be visualised on the Display. In order to change this
setting, press the same button until you have selected the status of the buzzer that you desire. Wait for
approximately 6 seconds, without changing your choice, following this, the sound of the BUZZER will confirm
that the setting has been memorised.
• End of cycle
Once the washing cycle is finished , the program number will appear lit up and still on the display, if it
is flashing wait for the end of the cycle.
• Checking the functions
During the washing phase it is possible to visualise the various functions in the following manner:
By pressing the program selection button , the number of the pre-set program will be visualised on the
display.
By pressing the half load button , the upper or lower washing area will be seen.
By pressing the drying button , the level of drying will be seen.
Stop
After the wash cycle, the dishwasher stops automatically, then unit will emit a long buzz to indicate the end of
the wahing cycle. To turn it off, press the button on/off . After each wash cycle, the water faucet must be
closed to insulate the appliance from the water supply system.
9
10
11
12
12
13
13
7
8
7
14
13
13
13
8
10
12
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Newpol XD900IXDG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Newpol XD900IXDG in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 5,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info