629272

NetworX NX-116E Manual

17
Zoom out
Zoom in
Previous page
1/20
Next page
15
SERVICE MENU
The service light will be “on” if the s ecurity system requires service. If the
service light is “on”, press the [ ] key followed by the [2] key to determine the
service condition. One or more zone lights will illuminate indicating what
service(s) is required. Call your service provider immediately for these
problems. Below is a listing of what each light means in a service condition.
LIGHT
PROBLEM
1
SYSTEM FAULT - Press the [1] key. The zone light(s) that is
illuminated corresponds to the system fault(s) below:
1 Over Current Fault
2 Siren Trouble
3 Box Tamper
4 Expander Power
5 Expander Low Battery
6 Expander Box Tamper
7 Expander Trouble
8 Ground Fault
Note: Faults 1 & 2 are global in nature and will affect all partitions of
a multi-partition system. Press the [#] key to return to the 1 of 8
service lights.
2
ZONE TAMPER - Press the [2] key and the zone light(s) will illuminate
showing the zone(s) that are tampered. Press the [#] key to return to
the 1 of 8 service lights.
3
ZONE LOW BATTERY - Press the [3] key. The zone light(s) will
illuminate showing which zone(s) has a low battery. This only applies
to wireless zones. Press the [#] key to return to the 1 of 8 service lights.
4
ZONE LOSS OF SUPERVISION - Press the [4] key and the zone light(s)
will illuminate showing which zone(s) has loss of supervision. This
only applies to wireless zones. Press [#] key to return to the 1 of 8
service lights.
5
ZONE TROUBLE - Press the [5] key and the zone light(s) will illuminate
showing which zone(s) has a trouble condition. Press the [#] key to
return to the 1 of 8 service lights.
6
TELEPHONE FAULT - Press the [6] key. The zone light(s) that is
illuminated corresponds to the system fault(s) below:
6
Line Trouble / Line Cut - This light will illuminate when there is
telephone line trouble or the telephone line has been cut. The
service light will remain lit until the telephone trouble clears
and a user code is entered.
7
Auxiliary Comm Device Fail - Radio backup has failed.
7
FAILURE TO COMMUNICATE - This light will illuminate when there is a
failure to communicate between your system and the central station.
8
LOSS OF SYSTEM TIME - This light will illuminate when there has
been a loss of power and your system clock needs to be reset.
Instructions are on page 13.
EXIT
Press the [#] key to exit the Service Light mode.
Note: This fault is global in nature and will affect all partitions of a multi-
partition system.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NetworX NX-116E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NetworX NX-116E in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info