608707
23
Zoom out
Zoom in
Previous page
1/46
Next page
350 East Plumeria Drive
San Jose, CA 95134
USA
September 2013
202-11314-02
Powerline PassThru Adapters
User Manual
Models:
XAV2602
XAV5401
XAV5602
XAV6501
XAV6504
2
Powerline PassThru Adapter
Support
Thank you for purchasing this NETGEAR product.
After installing your device, locate the serial number on the label of your product and use it to register your product
at
https://my.netgear.com. You must register your product before you can use NETGEAR telephone support.
NETGEAR recommends registering your product through the NETGEAR website. For product updates, additional
documentation, and support, visit
http://support.netgear.com.
Phone (US & Canada only): 1-888-NETGEAR.
Phone (Other Countries): Check the list of phone numbers at
http://support.netgear.com/general/contact/default.aspx.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of
NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change
without notice. © NETGEAR, Inc. All rights reserved.
3
Contents
Chapter 1 Getting Started
Hardware Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
XAV2602 Powerline 200 Nano PassThru Two-Port Adapter . . . . . . . . . .6
XAV5401 Powerline 500 PassThru One-Port Adapter. . . . . . . . . . . . . . .7
XAV5602 Powerline 500 Nano PassThru Two-Port Adapter . . . . . . . . . .8
XAV6501 Powerline 600 PassThru One-Port Adapter. . . . . . . . . . . . . . .9
XAV6504 Powerline 600 PassThru Four-Port Adapter . . . . . . . . . . . . .10
LED Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Button Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Filtered AC Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
How the Powerline PassThru Adapter Fits into Your Network . . . . . . . . . .12
Set Up the Powerline Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Set Up a New Powerline Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Add the Adapter to an Existing Powerline Network . . . . . . . . . . . . . . . .15
Powerline Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Use the Security Button to Set the Encryption Key . . . . . . . . . . . . . . . . . .16
Chapter 2 Using NETGEAR genie
Install NETGEAR genie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Powerline Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Security Icon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
View the Link Rate Between Powerline Devices . . . . . . . . . . . . . . . . . . . .22
Change the Name of a Powerline Device. . . . . . . . . . . . . . . . . . . . . . . . . .23
Turn LEDs Off or On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Set the Powerline Encryption Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Reset a Device to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . .26
Add a Device to the Powerline Network . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Chapter 3 Troubleshooting
Basic Functioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Troubleshooting Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Troubleshooting LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
LEDs Are Off When the Powerline Device Is Plugged In . . . . . . . . . . . .30
Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Powerline LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Ethernet LED Is Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
If You Do Not See All Your Devices with the NETGEAR genie . . . . . . . . .32
4
Powerline PassThru Adapter
If You Do Not See the Powerline Icon on Your Network Map . . . . . . . . . .32
Symantec Endpoint Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Appendix A Supplemental Information
XAV2602 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
XAV5401 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
XAV5602 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
XAV6501 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
XAV6504 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Appendix B Notification of Compliance
5
1
1. Getting Started
This chapter describes your Powerline PassThru adapter and how your adapter fits into a home
network. It also explains the security features and how to secure your Powerline network with a
private encryption key.
This chapter includes the following sections:
Hardware Features
How the Powerline PassThru Adapter Fits into Your Network
Set Up the Powerline Network
Powerline Network Security
Use the Security Button to Set the Encryption Key
For more information about the topics covered in this manual, visit the NETGEAR support
website at
http://support.netgear.com.
Getting Started
6
Powerline PassThru Adapter
Hardware Features
This section describes the hardware features of the Powerline PassThru adapters. Adapters
vary by region. Your adapter might look different.
XAV2602 Powerline 200 Nano PassThru Two-Port Adapter
The hardware features of the XAV2602 adapter are shown in the following figure.
Ethernet ports
Security
button
Factory Reset
button
Power
LED
Ethernet
LED
Powerline
LED
Filtered AC
socket
Figure 1. XAV2602 hardware features
Getting Started
7
Powerline PassThru Adapter
XAV5401 Powerline 500 PassThru One-Port Adapter
The hardware features of the XAV5401 adapter are shown in the following figure.
Ethernet port
Filtered AC
socket
Power LED
Powerline LED
Ethernet LED
Factory Reset
button
Security
button
Figure 2. XAV5401 hardware features
Getting Started
8
Powerline PassThru Adapter
XAV5602 Powerline 500 Nano PassThru Two-Port Adapter
The hardware features of the XAV5602 adapter are shown in the following figure.
Ethernet ports
Power
LED
Ethernet
LED
Powerline
LED
Filtered AC
socket
Security
button
Factory Reset
button
Figure 3. XAV5602 hardware features
Getting Started
9
Powerline PassThru Adapter
XAV6501 Powerline 600 PassThru One-Port Adapter
The hardware features of the XAV6501 adapter are shown in the following figure.
Factory Reset
button
Security
button
Filtered AC Ethernet LED
Power
LED
Powerline LED
Gigabit
Ethernet port
Ethernet LED On/Off switch
socket
Figure 4. XAV6501 hardware features
Getting Started
10
Powerline PassThru Adapter
XAV6504 Powerline 600 PassThru Four-Port Adapter
The hardware features of the XAV6504 adapter are shown in the following figure.
Factory Reset
button
Security
button
Filtered AC Ethernet LED
Power
LED
Powerline LED
Gigabit
Ethernet port
Ethernet LED On/Off
socket
switch
Ethernet
port
Figure 5. XAV6504 hardware features
Getting Started
11
Powerline PassThru Adapter
LED Descriptions
The LEDs indicate the status of your Powerline adapter
Table 1. LED descriptions
Item Description
Power LED
Solid green. The electrical power is on.
Blinking green. The
adapter is setting up security.
Amber.
The adapter is in power saving mode. If the Ethernet port is inactive for more
than ten minutes, the adapter enters power saving mode.
Off.
The adapter does not have electrical power or the LEDs were off using NETGEAR
genie.
Powerline LED
Solid. The adapter is connected to a Powerline network.
Off.
The adapter has not found any other compatible Powerline devices using the same
encryption key.
The Pick A Plug feature lets you pick the electrical outlet with the fastest link rate, indicated by
the color of the LED:
Green. Link rate > 80 Mbps
(Fast)
Amber. Link rate > 50 and
< 80 Mbps (Medium)
Red. Link rate < 50 Mbps
(Slow)
Ethernet LED
Solid green. The Powerline adapter is connected through the Ethernet port to a
powered-on Ethernet device.
Off. There
is no Ethernet connection.
.
Button Descriptions
Use the buttons on your Powerline adapter to do the following:
Factory Reset button. Use the Factory Reset button to return your Powerline PassThru
adapter to its factory default settings. Press the Factory Reset button for two seconds
and release it.
Security button.
After the Powerline adapters are active, you can use the Security
button to secure your Powerline network with a private encryption key. See Use the
Security Button to Set the Encryption Key on page 16.
Power On/Off switch. Use the Power On/Of
f switch to turn the device on and off. When
this switch is in the Off position, the filtered AC socket still has power.
Ethernet Port
Powerline adapters use an Ethernet port to convert a standard electrical wall outlet into a
high-speed wired network connection. You can use the wired network connection to bring
Internet connectivity to any device with an Ethernet port, such as a computer, game console,
Blu-ray player, smart TV, HD set-top box, or network DVR.
Getting Started
12
Powerline PassThru Adapter
Filtered AC Socket
The filtered AC socket can remove some electrical noise that might affect Powerline
performance. Plugging the power plugs of nearby devices into the filtered AC socket
improves performance.
Product Label
The product label provides unique details specific to your device, including the following
information:
Model number
Powerline MAC address
Ethernet MAC address
Serial number
Device password
How the Powerline PassThru Adapter Fits into Your
Network
You can use one or more Powerline adapters to extend Internet access throughout your
home.
A Powerline network consists of two or more compatible Powerline devices that
communicate with each other using your electrical power lines. One of the Powerline devices
is connected with an Ethernet cable to your router so that the Powerline network is linked to
your local area network (LAN). Connecting one Powerline device to your router allows all the
Powerline devices on the Powerline network to communicate with the router and use its
Internet connection.
Getting Started
13
Powerline PassThru Adapter
The following illustration shows a Powerline network with one Powerline device in Room 1
and a second Powerline device in Room 2.
Room 1
Room 2
Figure 6. A Powerline network with two Powerline PassThru adapters
To form a Powerline network, you need at least two compatible Powerline devices.
For best performance, follow these guidelines when you plan the location of your Powerline
devices:
Use an electrical outlet that is not controlled by a wall switch to avoid accidentally turning
of
f the power to the outlet.
A
void plugging Powerline products into electrical outlets that are located near appliances
that consume a lot of power, such as washers, dryers, or refrigerators. Interference from
these appliances might prevent Powerline products from working correctly or reduce
Powerline network performance.
Do not plug Powerline products into a power strip, extension cord, or surge protector
.
Connecting a Powerline product to one of these devices might prevent the product from
working correctly or reduce Powerline network performance.
Getting Started
14
Powerline PassThru Adapter
Set Up the Powerline Network
You can set up a new Powerline network that includes the Powerline PassThru adapter or you
can add the Powerline PassThru adapter to an existing Powerline network.
Set Up a New Powerline Network
Different Powerline models can share the same Powerline network. All NETGEAR Powerline
AV products are compatible.
To set up a new Powerline network:
1. Make sure that your wired Ethernet connections are
working:
a. If you have an existing wireless network, make
sure that it is connected to the Internet.
b. On a computer that is connected to your router or
gateway using an Ethernet cable, open a web
browser and navigate to a web page.
c. On a computer or device that is connected to your
wireless network, open a web browser and
navigate to a web page.
2. Plug the one Powerline device into a wall outlet near
your router or gateway
.
3. Connect the device to the LAN port on your router or
gateway using an Ethernet cable.
4. Plug the second Powerline device into a wall outlet where
you want to add Internet access.
Second
Powerline
device
5. (Optional) Use the Ethernet cable that came with your
adapter to connect the Powerline device to an Ethernet
port on a computer
, game console, Blu-ray player, or
other peripheral device.
The Powerline devices attempt to detect each other
and form a Powerline network.
6. Wait for the Powerline network to recognize each
Powerline device.
This process could take as little as 5 seconds or up to
80 seconds.
First
Powerline
device
Getting Started
15
Powerline PassThru Adapter
When the Power and Powerline LEDs stop blinking, the process is complete. If the
Powerline LEDs are green or amber, the devices are successfully connected to the
Powerline network. A red Powerline LED indicates a slow link rate. In this case, move the
Powerline device to another electrical outlet with a faster connection.
7. Secure your Powerline network.
See Use the Security Button to Set the Encryption Key on page 16.
Add the Adapter to an Existing Powerline Network
If you have an existing Powerline network, make sure that one of the Powerline devices is
connected to your router or gateway so that the Powerline network is linked to your local area
network (LAN). Your Powerline network must have two or more compatible Powerline
devices that communicate with each other.
To add the Powerline PassThru adapter to a Powerline network:
1. If you used the Security buttons or NETGEAR genie to secure your Powerline network,
press the Factory Reset button for two seconds on each Powerline device to return it to
its factory default settings.
This method is the quickest way to allow your Powerline PassThru adapter to
communicate with the other Powerline devices.
2.
Plug the Powerline PassThru adapter into a wall outlet
where you want to add Internet access.
3. (Optional) Use the Ethernet cable that came with your
adapter to connect the adapter to an Ethernet port on a
computer
, game console, Blu-ray player, or other
peripheral device.
The Powerline devices attempt to detect each other
and form a Powerline network.
4. Wait for the Powerline network to recognize each
Powerline device.
This process could take as little as 5 seconds or up to
80 seconds.
When the Power and Powerline LEDs stop blinking,
the process is complete. If the Powerline LEDs are
green or amber
, the devices are successfully
connected to the Powerline network. A red Powerline
LED indicates a slow link rate. In this case, move the Powerline device to another
electrical outlet with a faster connection.
5. Secure your Powerline network.
See Use the Security Button to Set the Encryption Key on page 16.
Getting Started
16
Powerline PassThru Adapter
Powerline Network Security
A Powerline network consists of two or more Powerline devices using the same network
encryption key. Securing your network is crucial. By encrypting the information that you send
over the Powerline network, you help to keep it secure from hackers. If you do not set up
security on your network, anyone nearby with a Powerline network can potentially use his or
her connection to gain access to your network and information that you send over the
Internet. This concern is especially relevant in settings such as apartment buildings, office
buildings, dorm rooms, and other more populated areas.
You can use either the Security button on the Powerline device or NETGEAR genie to secure
your Powerline network:
Use the Security button on the Powerline device to automatically generate a random
private encryption key. See
Use the Security Button to Set the Encryption Key on
page 16.
Use NETGEAR genie to configure your Powerline network with a private encryption key
that you specify. See
Chapter 2, Using NETGEAR genie.
Use the Security Button to Set the Encryption Key
Note: A Powerline device can generate a random private encryption key
only once. If you want to generate a new random key, first reset the
Powerline devices to their factory default settings. Either press the
Factory Reset button for two seconds, then release it, or use the
NETGEAR genie factory reset feature. (See
Reset a Device to
Factory Default Settings on page 26.)
You can use the Security button to replace the default encryption key with a random private
encryption key. The default encryption key is HomePlugAV.
To set the encryption key:
1. Make sure that all of the Powerline devices that you want to configure are plugged in by
checking that the Power and Powerline LEDs on each device are lit solid green.
CAUTION:
Do not press the Security button on the Powerline devices until the Power
and Powerline LEDs on each Powerline device are lit solid green. Pressing
the Security button too soon can temporarily disable Powerline
communication. If Powerline communication is disabled, reset the
Powerline device to its factory default settings by pressing the Factory
Reset button for two seconds, then releasing it.
Getting Started
17
Powerline PassThru Adapter
2. Press the Security button on the first Powerline device for two seconds.
The Power LED starts blinking after you release the button. then the Powerline device
automatically creates a new
, randomly generated encryption key that all other Powerline
devices on the network will use.
At this point, the Powerline devices cannot communicate with each other.
3. Within two minutes of pressing the Security button on the first Powerline device, press the
Security button on the second Powerline device for two seconds.
You must press both Security buttons within two minutes.
The Power LED starts blinking after you release the button. This process allows the
second Powerline device to use the same private encryption key as the first device so
that they can communicate.
When the Power LEDs stop blinking and the Powerline LEDs are lit solid green, the two
devices can communicate over the Powerline network in a secure way.
Note: This process works for only one pair of Powerline devices at a time.
If you have more than two Powerline devices, repeat this process for
each additional Powerline device to be configured.
The devices retain security settings even if they are unplugged.
18
2
2. Using NETGEAR genie
This chapter explains how to install NETGEAR genie and use it to manage your Powerline
network. NETGEAR genie works with all Powerline devices.
You can use NETGEAR genie to manage a local Powerline device that is connected to your
computer with an Ethernet cable and also to manage other Powerline devices on the same
network.
This chapter includes the following sections:
Install NETGEAR genie
Powerline Map
View the Link Rate Between Powerline Devices
Change the Name of a Powerline Device
Turn LEDs Off or On
Set the Powerline Encryption Key
Reset a Device to Factory Default Settings
Add a Device to the Powerline Network
Using NETGEAR genie
19
Powerline PassThru Adapter
Install NETGEAR genie
NETGEAR genie allows you to set a private encryption key for your Powerline network and
manage devices on your Powerline network.
You can manage the Powerline network using any computer that is connected to your
Powerline network. You can manage all devices on a Powerline network from one computer.
Note: If NETGEAR genie is already installed on your computer, you must
reinstall the latest version to get support for Powerline products.
NETGEAR genie is a free download available from the NETGEAR website.
To install NETGEAR genie on your computer:
1. Launch an Internet browser and visit www.netgear.com/genie.
2. Download the version of NETGEAR genie that corresponds to your operating system.
3. Run the file that you downloaded and follow the setup prompts to install NETGEAR genie.
4. Click the Finish button to complete the setup.
The NETGEAR genie shortcut icon displays on your desktop.
NETGEAR genie is installed on your computer.
Using NETGEAR genie
20
Powerline PassThru Adapter
Powerline Map
You can use genie’s Powerline map to view and manage your Powerline network.
To navigate to the Powerline map:
1. On a computer that is connected to your Powerline network, launch NETGEAR genie.
2. From the NETGEAR genie Home screen, click Network Map on the dashboard.
The Network Map screen displays.
3. Click the Powerline icon.
The Powerline map displays.
Using NETGEAR genie
21
Powerline PassThru Adapter
4. To view management options, right-click the icon of the device that you want to manage.
If all devices are not shown, click the Refresh icon to update the screen.
5. T
o view more information about a device, move your cursor over a device icon.
Refresh
icon
Device
information
Powerline
icon
Security
icon
Device
icon
Security Icon
Click the Security icon on the Powerline map to go to the Security screen.
If the Powerline devices are secured using the default encryption key, the
unlocked Security icon displays.
If the Powerline devices are secured using a private encryption key
, the locked
Security icon displays.
For more information about setting the encryption key, see Set the Powerline
Encryption Key on page 24.
Using NETGEAR genie
22
Powerline PassThru Adapter
View the Link Rate Between Powerline Devices
To view the link rate between your Powerline devices:
On the Powerline map, click the icon of the device whose link rate you want to view.
A pop-up screen displays.
Tx indicates the rate at which the device is transmitting data. Rx indicates the rate at
which the device is receiving data.
Using NETGEAR genie
23
Powerline PassThru Adapter
Change the Name of a Powerline Device
Powerline devices are identified by their model number and name. NETGEAR genie detects
any Powerline devices that are connected to the Powerline network and displays them on the
Powerline map. If you did not name the device, no name displays below the model number of
the device.
To name a Powerline device on your Powerline network:
1. On the Powerline map, right-click the icon of the device that you want to name.
2. On the pop-up menu that displays, select Device Name.
A pop-up screen displays advising you that connectivity will be temporarily lost while the
device is being renamed.
3. Click the OK button.
The following screen displays:
4. Enter a new name for the Powerline device and click the OK button.
Your changes are saved.
Using NETGEAR genie
24
Powerline PassThru Adapter
Turn LEDs Off or On
You can turn off or turn on the LEDs of any device on your Powerline network.
To turn the LEDs off or on:
1. On the Powerline map, right-click the icon of the device.
2. On the pop-up menu that displays, select either T
urn LED off or Turn LED on.
A pop-up screen displays advising you that connectivity will be temporarily lost while the
LEDs are being reset.
3. Click the OK button.
A message displays indicating that the operation was successful.
4. Click the OK button.
Set the Powerline Encryption Key
Powerline devices on the same Powerline network use the same encryption key. The factory
default encryption key is HomePlugAV.
In locations such as apartment buildings or office buildings, other people might use the same
electrical power lines that you use for your Powerline network. To protect your Powerline
network from unwanted access, you can use NETGEAR genie to set a private encryption key
for your Powerline devices. Make sure that all of your Powerline devices use the same
encryption key so that they can communicate with each other.
If you forget your private encryption key, you can reset the encryption key to the factory
default key
, HomePlugAV. See Reset a Device to Factory Default Settings on page 26.
To set the encryption key:
1. On the Powerline map, right-click the icon of a Powerline device in your network.
2. On the pop-up menu that displays, select Security.
Using NETGEAR genie
25
Powerline PassThru Adapter
The Security screen displays.
The top section of the Security screen shows information about each device that
NETGEAR genie detects:
Device Name. The list of Powerline devices that NETGEAR genie detects after
completing a device scan. The device name is listed as un-named by default, but you
can change it to a descriptive name, such as Office or Master Bedroom. (See Change
the Name of a Powerline Device on page 23.)
Model.
The model number of the Powerline device.
MAC Address.
The MAC address of the Powerline device. This information is on the
product label, which might not be visible when the device is plugged in.
Device Password. If your computer is not connected locally (with an Ethernet cable)
to the device that you want to configure, you must enter the device password.
The
device password is on the product label.
3. Select the check box next to each device that you want to configure.
4. Select an encryption key option for your Powerline devices:
Create a new Encryption Key. To set your own private encryption key, type the key
that you want to use in the field.
Use default Encryption Key. When you select this radio button, the factory default
encryption key automatically displays in the field.
The factory default encryption key is
HomePlugAV.
Using NETGEAR genie
26
Powerline PassThru Adapter
Note: If your computer is not connected locally (with an Ethernet cable) to
the device that you want to configure, you must enter the device
password. The device password is printed on the product label.
5. Click the Apply Security to Selected Devices button.
When the encryption key is set, a message displays indicating that the operation was
successful.
6. Click the OK button.
Reset a Device to Factory Default Settings
You can reset the encryption key of a Powerline device to the factory default key,
HomePlugAV.
Note: If your Powerline network uses a private encryption key, resetting a
Powerline device to its factory default settings disconnects the
device from the network. To avoid disconnecting your computer
from the network, reset all other Powerline devices on the network
before you reset the device that is connected to your computer.
To reset a device to its factory default settings:
1. On the Powerline map, right-click the icon of the device that you want to reset.
2. On the pop-up menu that displays, select Factory Reset.
A pop-up screen displays advising you that connectivity will be temporarily lost while the
device is being reset.
3. Click the OK button.
A message displays asking you to confirm the reset.
4. Click the OK button.
A message indicates whether the operation succeeded.
Using NETGEAR genie
27
Powerline PassThru Adapter
Add a Device to the Powerline Network
If you are adding a device to your Powerline network and your network uses the default
encryption key, plug the new device into a power outlet.
If your Powerline network uses a private encryption key, you can set the security in one of
two ways:
Use the Security button to add the new device to your network. See Use the Security
Button to Set the Encryption Key on page 16.
Use NETGEAR genie to add the new device to your network, as described in the
following procedure.
To add a Powerline device to the Powerline network using NETGEAR genie:
1. Plug the Powerline device into a wall outlet near your computer for initial setup.
2. Connect the Powerline device to an Ethernet port on your computer using the Ethernet
cable that came with your adapter
.
3. Install NETGEAR genie on the computer
.
See Install NETGEAR genie on page 19.
4. Launch NETGEAR genie on the computer and navigate to the Powerline map.
See Powerline Map on page 20.
5. Click the Refresh icon and wait for NETGEAR genie to detect the new device.
6. Right-click the new device’s icon.
7. On the pop-up menu that displays, select Security.
8. Set the encryption key for the device.
See Set the Powerline Encryption Key on page 24.
Make sure that you enter the same encryption key that
your other Powerline devices use.
Using NETGEAR genie
28
Powerline PassThru Adapter
9. On the Powerline map, click the Refresh icon.
10. Verify that all the devices on your Powerline network display on the screen.
It might take a minute or two for NETGEAR genie to detect all devices on the network.
29
3
3. Troubleshooting
This chapter provides information to help you diagnose and solve problems that you might
encounter. If you do not find the solution here, visit the NETGEAR support site at
http://support.netgear.com for product and contact information.
This chapter includes the following sections:
Basic Functioning
Troubleshooting Buttons
If You Do Not See All Your Devices with the NETGEAR genie
If You Do Not See the Powerline Icon on Your Network Map
Symantec Endpoint Protection
Troubleshooting
30
Powerline PassThru Adapter
Basic Functioning
After you plug in the Powerline device, the following sequence of events occurs:
1. The Power LED lights.
2. After approximately ten seconds, verify the following:
The Power LED is solid green. The device is powered on.
If the device is connected to a Powerline network, the Powerline LED is lit.
If the Powerline device is connected through the Ethernet port to a powered-on
Ethernet device, the Ethernet LED is lit.
Troubleshooting Buttons
The Factory Reset and Security buttons are on the side panel of the Powerline device.
Pressing the Factory Reset button longer than two seconds does not reset the device.
Pressing the Security button longer than two seconds does not activate security.
Troubleshooting LEDs
The LEDs indicate activity; you can use them for troubleshooting.
LEDs Are Off When the Powerline Device Is Plugged In
Make sure that power is supplied to the electrical outlet.
If power is supplied and the LEDs stay off, someone might have used NETGEAR genie to
turn off the LEDs. Use NETGEAR genie to check whether the LEDs are turned off. If they are
turned off, you can use NETGEAR genie to turn them back on. See
Turn LEDs Off or On on
page 24.
Power LED
If the Power LED is off, the adapter does not have electrical power. Try these troubleshooting
tips:
Make sure that power is supplied to the electrical outlet and that the Powerline device is
not plugged into an extension cord, power strip, or surge protector.
Press the Factory Reset button on the Powerline device for two seconds to return the
device to its factory default settings.
Troubleshooting
31
Powerline PassThru Adapter
If the Power LED is amber, the adapter is in power saving mode. The adapter enters power
saving mode occurs when the Ethernet link is inactive for more than ten minutes. The
Ethernet link is inactive if any of the following occurs:
The Ethernet cable is unplugged.
The peripheral device that is connected through the Ethernet port is turned off.
The Powerline adapter is idle.
To wake a Powerline device from power saving mode:
1. Connect a powered-on Ethernet device to one end of the Ethernet cable.
2. Connect the Powerline device to the other end of the Ethernet cable.
The Powerline device returns to normal mode within two seconds.
Powerline LED
If the Powerline LED is off, the Powerline devices cannot find each other. Try these
troubleshooting tips:
Make sure that the Powerline devices are plugged into wall outlets with power and that
they use the same network encryption key.
Move the Powerline device to an outlet that is closer to the computer or devices.
If you set a private encryption key, make sure that all Powerline devices are using the
same encryption key.
If the problem occurred after you set the encryption key, reset each device to its factory
default settings. Then try setting the encryption key again.
Amber or red. Move the Powerline device to another electrical outlet with a faster
connection.
Ethernet LED Is Off
If the Ethernet LED is off, the adapter does not have an Ethernet connection. Try these
troubleshooting tips:
If your Powerline device is connected to the LAN port of your router, check the following:
Your router and modem are turned on.
The computer connected directly to the router can access the Internet.
If your Powerline device is connected to a computer, game console, Blu-ray player, or
other peripheral device, check the following:
The peripheral device is turned on.
The Powerline device is securely connected to the peripheral device using an
Ethernet cable.
Press the Factory Reset button on each Powerline device for two seconds to return the
device to its factory default settings.
Troubleshooting
32
Powerline PassThru Adapter
If You Do Not See All Your Devices with the NETGEAR
genie
If you click the Refresh icon on the NETGEAR genie Powerline map and you do not see all
the devices that you expect, some Powerline devices might be using different encryption
keys. If the encryption keys are different, do one of the following:
Reset your Powerline devices to their factory default settings, then set the encryption key
for all of your Powerline devices.
Connect your computer to one Powerline device at a time and use NETGEAR genie to
set the encryption key for each device.
If You Do Not See the Powerline Icon on Your Network
Map
If you navigate to the Network Map on NETGEAR genie and you do not see the Powerline
icon, try these troubleshooting tips:
Make sure that you have the latest version of NETGEAR genie installed. Some older
versions of NETGEAR genie might not support Powerline products.
Temporarily disable your antivirus software and relaunch NETGEAR genie. Your
computer’s antivirus software might be blocking the Powerline communication protocol.
Symantec Endpoint Protection
The antivirus software Symantec Endpoint Protection v11.0.5002.333 filters the NETGEAR
Powerline network traffic and prevents Powerline devices from appearing on the Network
Map. To allow Powerline network traffic to pass through the Symantec Endpoint Protection
filter, you must add a firewall rule to the filter.
Note: Symantec Endpoint Protection v12.0.1001.95 does not have this
issue.
To add a firewall rule for your Powerline devices:
1. Open the Symantec Control Center and click the Options button under Network Threat
Protection.
Troubleshooting
33
Powerline PassThru Adapter
2. Select Configure Firewall Rules from the menu.
The following screen displays:
3. Click the Add button.
Troubleshooting
34
Powerline PassThru Adapter
The following screen displays:
4. In the General tab, do the following:
a. In the Rule name field, type a name for the firewall rule.
b. Select the Allow this traffic radio button.
c. Configure the firewall settings as shown or as you prefer
.
5. Click the Ports and Protocols tab.
Troubleshooting
35
Powerline PassThru Adapter
The following screen displays:
a. From the Protocol drop-down menu, select Ethernet.
b. In the Ethernet type field, type 0x88E1.
c. Click the OK button.
The rule displays in the firewall rule list.
6. Make sure that the check box next to the rule is selected and click the OK button.
7. Restart the computer and launch NETGEAR genie.
The Powerline icon displays on the Network Map screen.
36
A
A. Supplemental Information
This appendix provides technical specifications and safety information for Powerline PassThru
Adapters.
This appendix includes the following sections:
XAV2602 Technical Specifications
XAV5401 Technical Specifications
XAV5602 Technical Specifications
XAV6501 Technical Specifications
XAV6504 Technical Specifications
Safety Information
Supplemental Information
37
Powerline PassThru Adapter
XAV2602 Technical Specifications
The XAV2602 adapter meets the technical specifications defined in the following table.
Table 2. XAV2602 technical specifications
Feature Specification
Data and routing protocols IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-Tx)
AC input 100–240V, 0.2A (max.)
Socket outlet rating (max. load) AU: 10A, 250V; EU: 16A, 250V; NA: 15A, 125V; UK: 13A, 250V;
Power consumption Normal: 4W, Power saving mode: <0.5W
Dimensions 114 x 55 x 32.5 mm (4.49 x 2.17 x 1.28 in)
Weight 0.190 kg (0.418 lb)
Operating temperature 0° to 40°C (32º to 104ºF)
Operating humidity 10–90% maximum relative humidity, noncondensing
Storage humidity 5–95% maximum relative humidity, noncondensing
Security encryption type 128-bit AES
MAC addresses 8 (active) / 16 (total): number of nodes that can be added to a
single network
Bandwidth 200 Mbps
Compatibility HomePlug AV IEEE 1901
(Not compatible with HomePlug v1.0 or HomePlug v1.0 Turbo)
Data transfer rate Up to 200 Mbps with real throughput greater than 80 Mbps
Frequency band 2–75 Mbps
Modulation type OFDM symbol modulation
Electromagnetic emissions FCC Part 15 Class B; CE-EMC Class B; 3-home FCC Certificate
Safety agency approvals UL Listed (UL 1950) /cUL IEC950; CE LVD; TUV CB, TUV CG
Supplemental Information
38
Powerline PassThru Adapter
XAV5401 Technical Specifications
The XAV5401 adapter meets the technical specifications defined in the following table.
Table 3. XAV5401 technical specifications
Feature Specification
Data and routing protocols IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-Tx)
AC input 100–240V, 0.2A (max.)
Socket outlet rating (max. load) AU: 10A, 250V; EU: 16A, 250V; NA: 15A, 125V; UK: 13A, 250V;
Power consumption Normal: 4W, Power saving mode: <0.5W
Dimensions 114 x 55 x 32.5 mm (4.49 x 2.17 x 1.28 in)
Weight 0.174 kg (0.384 lb)
Operating temperature 0° to 40°C (32º to 104ºF)
Operating humidity 10–90% maximum relative humidity, noncondensing
Storage humidity 5–95% maximum relative humidity, noncondensing
Security encryption type 128-bit AES
MAC addresses 8 (active) / 16 (total): number of nodes that can be added to a
single network
Bandwidth 500 Mbps
Compatibility HomePlug AV IEEE 1901
(Not compatible with HomePlug v1.0 or HomePlug v1.0 Turbo)
Data transfer rate Up to 500 Mbps with real throughput greater than 80 Mbps
Frequency band 2–75 Mbps
Modulation type OFDM symbol modulation
Electromagnetic emissions CE-EMC Class B
Safety agency approvals IEC60950; CE LVD
Supplemental Information
39
Powerline PassThru Adapter
XAV5602 Technical Specifications
The XAV5602 adapter meets the technical specifications defined in the following table.
Table 4. XAV5602 technical specifications
Feature Specification
Data and routing protocols IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-Tx)
AC input 100–240V, 0.2A (max.)
Socket outlet rating (max. load) AU: 10A, 250V; EU: 16A, 250V; NA: 15A, 125V; UK: 13A, 250V;
Power consumption Normal: 4W, Power saving mode: <0.5W
Dimensions 114 x 55 x 32.5 mm (4.5 x 2.2 x 1.28 in)
Weight 174 g (0.38 lb)
Operating temperature 0° to 40°C (32º to 104ºF)
Operating humidity 10–90% maximum relative humidity, noncondensing
Storage humidity 5–95% maximum relative humidity, noncondensing
Security encryption type 128-bit AES
MAC addresses 8 (active) / 16 (total): number of nodes that can be added to a single
network
Bandwidth 500 Mbps
Compatibility HomePlug AV IEEE 1901
(Not compatible with HomePlug v1.0 or HomePlug v1.0 Turbo)
Data transfer rate Up to 500 Mbps with real throughput greater than 80 Mbps
Frequency band 2–75 Mbps
Modulation type OFDM symbol modulation
Electromagnetic emissions FCC Part 15 Class B; CE-EMC Class B; 3-home FCC Certificate
Safety agency approvals UL Listed (UL 1950) /cUL IEC950; CE LVD; TUV CB, TUV CG
Supplemental Information
40
Powerline PassThru Adapter
XAV6501 Technical Specifications
The XAV6501 adapter meets the technical specifications defined in the following table.
Table 5. XAV6501 technical specifications
Feature Specification
Data and routing protocols IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-Tx)
AC input 100–240V, 0.2A (max.)
Socket outlet rating (max. load) AU: 10A, 250V; EU: 16A, 250V; NA: 15A, 125V; UK: 13A, 250V;
Power consumption Normal: 4W, Power saving mode: <0.5W
Dimensions 114 x 55 x 32.5 mm (4.5 x 2.2 x 1.28 in)
Weight 174 g (0.38 lb)
Operating temperature 0° to 40°C (32º to 104ºF)
Operating humidity 10–90% maximum relative humidity, noncondensing
Storage humidity 5–95% maximum relative humidity, noncondensing
Security encryption type 128-bit AES
MAC addresses 8 (active) / 16 (total): number of nodes that can be added to a single
network
Bandwidth 600 Mbps
Compatibility HomePlug AV IEEE 1901
(Not compatible with HomePlug v1.0 or HomePlug v1.0 Turbo)
Data transfer rate Up to 600 Mbps with real throughput greater than 80 Mbps
Frequency band 2–75 Mbps
Modulation type OFDM symbol modulation
Electromagnetic emissions FCC Part 15 Class B; CE-EMC Class B; 3-home FCC Certificate
Safety agency approvals UL Listed (UL 1950) /cUL IEC950; CE LVD; TUV CB, TUV CG
Supplemental Information
41
Powerline PassThru Adapter
XAV6504 Technical Specifications
The XAV6504 adapter meets the technical specifications defined in the following table.
Table 6. XAV6504 technical specifications
Feature Specification
Data and routing protocols IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-Tx)
AC input 100–240V, 0.2A (max.)
Socket outlet rating (max. load) AU: 10A, 250V; EU: 16A, 250V; NA: 15A, 125V; UK: 13A, 250V;
Power consumption Normal: 4W, Power saving mode: <0.5W
Dimensions 114 x 55 x 32.5 mm (4.5 x 2.2 x 1.28 in)
Weight 174 g (0.38 lb)
Operating temperature 0° to 40°C (32º to 104ºF)
Operating humidity 10–90% maximum relative humidity, noncondensing
Storage humidity 5–95% maximum relative humidity, noncondensing
Security encryption type 128-bit AES
MAC addresses 8 (active) / 16 (total): number of nodes that can be added to a single
network
Bandwidth 600 Mbps
Compatibility HomePlug AV IEEE 1901
(Not compatible with HomePlug v1.0 or HomePlug v1.0 Turbo)
Data transfer rate Up to 600 Mbps with real throughput greater than 80 Mbps
Frequency band 2–75 Mbps
Modulation type OFDM symbol modulation
Electromagnetic emissions FCC Part 15 Class B; CE-EMC Class B; 3-home FCC Certificate
Safety agency approvals UL Listed (UL 1950) /cUL IEC950; CE LVD; TUV CB, TUV CG
Supplemental Information
42
Powerline PassThru Adapter
Safety Information
Follow these safety guidelines to ensure your own personal safety and to help protect your
system from potential damage:
For national approvals (approval schemes other than CB), relevant national standards for
plug, socket-outlet, and direct plug-in units (for example, US) shall also be consulted
while testing and approving such products according to the national standards.
Check the electrical current for any device plugged into the filtered AC socket. Do not
exceed home and product outlet ratings and electrical requirements.
The socket-outlet shall be installed near the equipment and be easily accessible.
Only power cords are allowed to be inserted into the filtered AC socket; no other
equipment with a direct plug-in is allowed. Power cords needs to be a maximum of 1 m
long and a minimum of 0.75 mm
2
of cross-sectional area.
Do not plug devices into the Powerline PassThru Adapter filtered AC outlet that exceed
the product ratings. The output voltage of the filtered AC outlet is the same as the power
outlet that the Powerline PassThru Adapter is plugged into. To help avoid damaging your
system, be sure that the attached devices are electrically rated to operate with the power
available in your location.
If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket
of the Powerline PassThru Adapter might not perform as well as expected.
DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an
attached power strip. The device is not intended to be used with home appliances such
as air conditioners, power tools, space heaters, fans, hair dryers, ovens, or refrigerators.
Actual data throughput will vary. Network conditions and environmental factors, including
volume of network traffic, building materials and construction, and network overhead,
lower actual data throughput rate.
Do not service any product except as explained in your system documentation.
Opening or removing covers that are marked with the triangular symbol with a lightning
bolt can expose you to electrical shock. Only a trained service technician should service
components inside these compartments.
Use the product only with approved equipment.
Allow the product to cool before removing covers or touching internal components.
To help avoid damaging your system, be sure that the voltage selection switch (if
provided) on the power supply is set to match the power available at your location:
- 110 volts (V), 60 hertz (Hz) in most of North and South America and some Far
Eastern countries such as South Korea and Taiwan
- 100V, 50 Hz in eastern Japan and 100V, 60 Hz in western Japan
- 230V, 50 Hz in most of Europe, the Middle East, and the Far East
The peripheral power cables are equipped with three-prong plugs to help ensure proper
grounding. Do not use adapter plugs or remove the grounding prong from a cable.
Supplemental Information
43
Powerline PassThru Adapter
Observe extension cable and power strip ratings. Make sure that the total ampere rating
of all products plugged into the extension cable or power strip does not exceed 80
percent of the ampere ratings limit for the extension cable or power strip.
To help protect your system from sudden, transient increases and decreases in electrical
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
For additional safety instructions, see Appendix B, Notification of Compliance.
44
B
B. Notification of Compliance
Safety Instructions and Precautions
WARNING:
Use the following safety guidelines to ensure your own personal
safety and to help protect your product from potential damage. To
reduce the risk of bodily injury, electrical shock, fire, and damage
to the equipment, observe the following precautions.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Observe and follow service markings.
If any of the following conditions occur, unplug the product from the electrical outlet and
replace the part or contact your service provider/retailer:
- The power cable, extension cable, or plug is damaged.
- An object has fallen into the product.
- The product has been exposed to water.
- The product has been dropped or damaged.
- The product does not operate correctly when you follow the operating instructions.
Keep your system away from radiators and heat sources. Also, do not block cooling
vents.
Do not spill food or liquids on your system components, and never operate the product in
a wet environment.
Do not push any objects into the openings of your system. Doing so can cause fire or
electric shock by shorting out interior components.
Operate the product only from the type of external power source indicated on the
electrical ratings label.
Also, be sure that attached devices are electrically rated to operate with the power
available in your location.
Use only approved power cables. If you have not been provided with a power cable for
your system or for any AC-powered option intended for your system, purchase a power
cable that is approved for use in your country. The power cable must be rated for the
product and for the voltage and current marked on the product’s electrical ratings label.
Notification of Compliance
45
Powerline PassThru Adapter
The voltage and current rating of the cable should be greater than the ratings marked on
the product.
T
o help prevent electric shock, plug the system and peripheral power cables into properly
grounded electrical outlets.
Do not use adapter plugs. If you must use an extension cable, use a three-wire cable with
properly grounded plugs.
Observe extension cable and power strip ratings. Make sure that the total ampere rating
of all products plugged into the extension cable or power strip does not exceed 80
percent of the ampere ratings limit for the extension cable or power strip.
T
o help protect your system from sudden, transient increases and decreases in electrical
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; route cables so that they cannot be
stepped on or tripped over
. Be sure that nothing rests on any cables.
Do not modify power cables or plugs.
Always follow your local and national wiring rules.
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National laws for usage of radio
spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result
in unlawful operation and adverse action against the end-user by the applicable National regulatory authority.
This product's firmware limits operation to only the channels allowed in a particular Region or Country. Therefore, all
options described in this user's guide may not be available in your version of the product.
Europe – EU Declaration of Conformity
Products bearing the marking comply with the following EU directives:
EMC Directive 2004/108/EC
Low V
oltage Directive 2006/95/EC
If this product has telecommunications functionality, it also complies with the requirements of the following EU
Directive:
R&TTE Directive 1999/5/EC
Compliance with these directives implies conformity to harmonized European standards that are noted in the EU
Declaration of Conformity
.
FCC Requirements for Operation in the United States
FCC Information to User
This product does not contain any user serviceable components and is to be used with approved antennas only.
Any product changes or modifications will invalidate all applicable regulatory certifications and approvals
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Guidelines for Human Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Notification of Compliance
46
Powerline PassThru Adapter
FCC Declaration Of Conformity
We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that the
Powerline PassThru Adapter complies with Part 15 of FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following methods:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Modifications made to the product, unless expressly approved by NETGEAR, Inc., could void the user's right to
operate the equipment.
Canadian Department of Communications Radio Interference Regulations
This digital apparatus, the Powerline PassThru Adapter, does not exceed the Class B limits for radio-noise
emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of
Communications.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear XAV5401 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear XAV5401 in the language / languages: English as an attachment in your email.

The manual is 1,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info