519657
100
Zoom out
Zoom in
Previous page
1/112
Next page
100 | Chapter 7: Troubleshooting
N150 Wireless Router User Manual
Is your router’s wireless radio enabled? See Viewing Advanced Wireless Settings on
page 29.
Is your router’s SSID broadcast enabled? See Viewing Advanced Wireless Settings on
page 29.
Is your router set to a wireless standard that is not supported by your wireless adapter?
Check the Mode setting as described in
Viewing and Configuring Basic Internet Settings
on page 11.
If your wireless network appears, but the signal strength is weak, check these conditions:
Is your router too far from your adapter, or too close? Place the computer that has the
adapter near the router, but at least 6 feet away, and see whether the signal strength
improves.
Is your wireless signal obstructed by objects between the router and your adapter? See
Optimizing Wireless Performance on page 67.
Restoring the Default Configuration and Password
This section explains how to restore the factory default configuration settings that reset the
router’s user name to admin, the password to password, and the IP address to 192.168.1.1.
WARNING!
These procedures erase all current configuration settings.
You can erase the current configuration and restore factory defaults in two ways:
Use the Erase function of the router. To use the Erase function, see Erasing the
Configuration on page 84.
Use the restore factory settings button on the rear panel of the router. Use this method for
cases when the administration password or IP address is not known.
To use the restore settings button:
1. Locate the restore factory settings button on the rear panel of the router.
2. Use a sharp object such as a pen or a paper clip to press and hold the restore factory
settings button for about 5 seconds, until the Power light begins to blink.
3. Release the restore factory settings button, and wait for the router to restart, and for the
Power light to stop blinking and become solid green.
The factory default settings will be restored so that you can access the router from your
Web browser using the factory defaults.
If the wireless router fails to restart, or the Power light continues to blink or turns solid amber,
the unit might be defective. If the error persists, you might have a hardware problem and
should contact Technical Support at
http://www.netgear.com/support.
100


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WNR1000v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WNR1000v3 in the language / languages: English as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WNR1000v3

Netgear WNR1000v3 Installation Guide - English - 2 pages

Netgear WNR1000v3 Installation Guide - German - 2 pages

Netgear WNR1000v3 Installation Guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info