519657
49
Zoom out
Zoom in
Previous page
1/112
Next page
Chapter 4: Customizing Your Network Settings | 49
N150 Wireless Router User Manual
Configuring a Device Name
The device name is a user-friendly name for the router. This name is shown in the Network
on Windows Vista and the Network Explorer on all Windows systems. The Device Name
field cannot be blank. The default name is WNR1000v3h2.
Configuring LAN TCP/IP Setup Parameters
These are advanced settings that you might configure if you are a network administrator and
your network contains multiple routers. The router is shipped preconfigured to use private IP
addresses on the LAN side and to act as a DHCP server (see
Using the Router as a DHCP
Server on page 50).
Note: If you change the LAN IP address of the router while connected
through the browser, you will be disconnected. You must then open
a new connection to the new IP address and log in again.
The router’s default LAN IP configuration is:
LAN IP address. 192.168.1.1
Subnet mask. 255.255.255.0
These addresses are part of the designated private address range for use in private networks
and should be suitable for most applications. If your network has a requirement to use a
different IP addressing scheme, you can make those changes in this screen.
The LAN IP settings are:
IP Address. The LAN IP address of the router.
IP Subnet Mask. The LAN subnet mask of the router. Combined with the IP address, the
IP subnet mask allows a device to know which other addresses are local to it, and which
must be reached through a gateway or router.
RIP Direction. RIP allows a router to exchange routing information with other routers.
The RIP Direction selection controls how the router sends and receives RIP packets.
Both is the default.
- When set to Both or In Only, the router incorporates the RIP information that it
receives.
- When set to Both or Out Only, the router broadcasts its routing table periodically.
RIP Version. This controls the format and the broadcasting method of the RIP packets
sent by the router. (It recognizes both formats when receiving.) The default setting is
Disabled.
- RIP-1 is universally supported. RIP-1 is usually adequate unless you have an unusual
network setup.
- RIP-2B carries more information than RIP-1 and uses subnet broadcasting.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WNR1000v3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WNR1000v3 in the language / languages: English as an attachment in your email.

The manual is 4,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WNR1000v3

Netgear WNR1000v3 Installation Guide - English - 2 pages

Netgear WNR1000v3 Installation Guide - German - 2 pages

Netgear WNR1000v3 Installation Guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info