519682
63
Zoom out
Zoom in
Previous page
1/134
Next page
| 63
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
3. After completing the upload, the changes do not take effect until you activate them. On the
Configuration screen, next to Activate Changes, click Proceed. If your browser requires a
confirmation to proceed, confirm the action.
Rebooting and Restoring the Default Configuration
You can erase the wireless access point configurations, and return to the factory default
settings. After erasing, the wireless access point’s default LAN IP address will be
192.168.0.229, the default login user name will be admin, and the default login password will
be password.
Using the Software to Reboot and Restore Factory Default Settings
To use the software clear all or selected data and restore the factory default values:
1. On the Configuration screen (see Figure 4-1 on page 62), below Restore Factory
Default, next to Preserve Settings, select the Network settings checkbox if you want to
preserve the network settings such as the server IP address, subnet mask, default
gateway, DNS server, and management VLAN ID. If you do not want to preserver these
settings, deselect the Network settings checkbox.
2. Next to Restore Factory Default, click Proceed. If your browser requires a confirmation to
proceed, confirm the action. A few seconds later, only the power LED of the wireless access
point remains on, indicating that the wireless access point has rebooted.
After several minutes, the factory default configuration will be restored, and the wireless
access point will be ready for use.
Using the Reset Button to Reboot and Restore Factory Default Settings
If you do not know the LAN IP address, login user name, or login password, you can still
restore the factory default configuration settings with the Reset button. This button is on the
rear panel of the wireless access point (see
“Rear Panel” on page 11).
To use the Reset button to clear all data and restore the factory default values:
1. Push and hold the Reset button for about five seconds. (You may have to push hard.)
2. Release the Reset button. A few seconds later, only the power LED of the wireless access
point remains on, indicating that the wireless access point has rebooted.
After several minutes, the factory default configuration will be restored, and the wireless
access point will be ready for use.
Saving the Configuration to Flash Memory
This procedure saves any configuration changes to the internal flash memory, allowing the
changes to remain active after the wireless access point has been reloaded.To save the
configuration to flash memory:
On the Configuration screen (see Figure 4-1 on page 62), next to Save Configuration to
Flash, click Proceed. If your browser requires a confirmation to proceed, confirm the action.
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WGAP150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WGAP150 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WGAP150

Netgear WGAP150 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info