519682
26
Zoom out
Zoom in
Previous page
1/134
Next page
26 |
WG102-500, WGAP150 ProSafe™ 802.11g Wireless Access Point
3. Specify the 802.11n profile fields as explained Table 2-5.
Table 2-5. 802.11b/g Profile Settings
Field Descriptions
Radio Enable The radio is enabled by default. To turn off the radio, deselect the Radio Enable
checkbox. Doing so disables access through the wireless access point, which can
be helpful for configuration, network tuning, or troubleshooting activities.
Radio Policy Select one of the following modes from the pull-down menu:
802.11b/g. The wireless access point accepts both 802.11b and 802.11g client
association requests. This mode is also referred to as Mixed Mode.
802.11b Only. The wireless access point accepts 802.11b client association
requests only.
802.11g Only. The wireless access point accepts 802.11g client association
requests only.
Country This pull-down menu lets you specify your country/region.
RF Channel This pull-down menu lets you to specify the 802.11 channel. The available options
for 802.11b or 802.11g are from 1 to 11 for the U.S. (which is the default setting) and
from 1 to 13 for Europe. For automatic channel selection, select Auto. For more
information about operating frequencies, see the guidelines about channels below
this table.
Tx Output Power This pull-down menu lets you to specify the transmission power. The available
options are from 27 dBm to 18 dBm. By default, the Tx Output Power is 27 dBm.
Note: Make sure that you comply with the regulatory requirements for total radio
frequency (RF) output power in your country.
You should not need to change the operating frequency (channel) unless you notice
interference problems, or are setting up the wireless access point near another wireless
access point. Observe the following guidelines:
Wireless access points use a fixed channel. You can select a channel that provides
the least interference and best performance. In the USA and Canada, 11 channels
are available.
If using multiple wireless access points, it is better if adjacent wireless access points
use different channels to reduce interference. The recommended channel spacing
between adjacent wireless access points is five channels (for example, use channels
1 and 6, or 6 and 11).
In “infrastructure” mode, wireless stations normally scan all channels, looking for a
wireless access point. If more than one wireless access point can be used, the one
with the strongest signal is used. This can happen only when the wireless access
points use the same SSID. The WGAP150 wireless access point functions in
“infrastructure” mode by default.
For more information about wireless channels, see the online document that you can
access from “Wireless Networking Basics” in Appendix B.
4. Click Save or Save to Flash & Activate to save your settings.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear WGAP150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear WGAP150 in the language / languages: English as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear WGAP150

Netgear WGAP150 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info