519502
13
Zoom out
Zoom in
Previous page
1/121
Next page
Reference Manual for the Model RP614 v2 Web Safe Router
Introduction 1-3
Autosensing Ethernet Connections with Auto Uplink™
With its internal 4-port 10/100 switch, the Model RP614 v2 can connect to either a 10 Mbps
standard Ethernet network or a 100 Mbps Fast Ethernet network. Both the LAN and WAN
interfaces are autosensing and capable of full-duplex or half-duplex operation.
The router incorporates Auto Uplink
TM
technology. Each Ethernet port will automatically sense
whether the Ethernet cable plugged into the port should have a ‘normal’ connection such as to a
PC or an ‘uplink’ connection such as to a switch or hub. That port will then configure itself to the
correct configuration. This feature also eliminates the need to worry about crossover cables, as
Auto Uplink will accommodate either type of cable to make the right connection.
Extensive Protocol Support
The RP614 v2 router supports the Transmission Control Protocol/Internet Protocol (TCP/IP) and
Routing Information Protocol
(RIP). For further information about TCP/IP, refer to Appendix B,
“Network, Routing, Firewall, and Basics.”
IP Address Sharing by NAT
The RP614 v2 router allows several networked PCs to share an Internet account using only a
single IP address, which may be statically or dynamically assigned by your Internet service
provider (ISP). This technique, known as NAT, allows the use of an inexpensive single-user
ISP account.
Automatic Configuration of Attached PCs by DHCP
The RP614 v2 router dynamically assigns network configuration information, including
IP, gateway, and domain name server
(DNS) addresses, to attached PCs on the LAN using the
Dynamic Host Configuration Protocol
(DHCP). This feature greatly simplifies configuration
of PCs on your local network.
DNS Proxy
When DHCP is enabled and no DNS addresses are specified, the router provides its own
address as a DNS server to the attached PCs. The router obtains actual DNS addresses from
the ISP during connection setup and forwards DNS requests from the LAN.
PPP over Ethernet
(PPPoE)
PPPoE is a protocol for connecting remote hosts to the Internet over a DSL connection by
simulating a dial-up connection. This feature eliminates the need to run a login program such
as Entersys or WinPOET on your PC.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear RP614 v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear RP614 v2 in the language / languages: English as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear RP614 v2

Netgear RP614 v2 Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info