544204
10
Zoom out
Zoom in
Previous page
1/127
Next page
Table 1. Front panel LED descriptions
LED Description
Power Solid amber. The router is starting up.
Blinking amber. The firmware is upgrading, or the Reset button was pressed.
Solid green. The router
is ready.
Blinking green. The firmware
is corrupted. See www.netgear.com/support.
Off. Power is not supplied to the router.
Internet
Solid green. The Internet connection is ready.
Solid amber. The Ethernet cable connection to the modem has been detected.
Off
. No Ethernet cable is connected to the modem.
Wireless
Solid blue. The wireless radio is operating in either 2.4 GHz or 5 GHz mode.
Blinking: The router is in WPS mode.
Off
. The wireless radios are off for both 2.4 GHz and 5 GHz.
USB
Solid blue: The USB device has been accepted by the router and is ready to be used.
Blinking blue: A second USB HDD is plugged in and is trying to connect.
Off
: No USB device is connected, someone clicked the Safely Remove Hardware button, and
it is now safe to remove the attached USB device.
Hardware Setup
10
R6300 WiFi Router 802.11ac Dual Band Gigabit
The WiFi On/Off and WPS buttons toggle the WiFi and WPS functions on and off.
WiFi On/Off button. Pressing and holding the WiFi On/Of
f button for 2 seconds turns the
2.4 GHz and 5 GHz wireless radios on and off. If the 2.4 GHz and 5 GHz LEDs are lit,
then the wireless radio is on. If these LEDs are off, then the wireless radios are turned off
and you cannot connect wirelessly to the router.
WPS button.
Y
ou can use this button to use WPS to add a wireless device or computer
to your wireless network. The LED below the WPS button blinks green when the router is
trying to add the wireless device or computer. The LED stays solid green when wireless
security is enabled in the router.
Back Panel
The back panel has the connections shown in the following figure.
USB Ethernet Internet
Power On/Off
Power connector
port
LAN ports 1–4
Reset
buttonport
Figure 3. Router, rear view
See Factory Settings on page 115 for information about restoring factory settings.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear Nighthawk R6300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear Nighthawk R6300 in the language / languages: English as an attachment in your email.

The manual is 6,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info