479740
33
Zoom out
Zoom in
Previous page
1/78
Next page
Version 1.0
November 2004
NETGEAR, Inc.
4500 Great America Parkway
Santa Clara, CA 95054 USA
Users Manual for the
Wireless Digital Media
Player MP115
ii
November 2004 202-10038-01
© 2004 by NETGEAR, Inc. All rights reserved.
Trademarks
NETGEAR is a trademark of Netgear, Inc.
Microsoft, Windows, and Windows Media Player are trademarks or registered trademarks of Microsoft Corporation.
RHAPSODY is a registered trademark of Listen.com.
Other brand and product names are registered trademarks or trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to
make changes to the products described in this document without notice.
NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit
layout(s) described herein.
Certificate of the Manufacturer/Importer
It is hereby certified that the Wireless Digital Media Player MP115 has been suppressed in accordance with the
conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992. The operation of some equipment (for example,
test transmitters) in accordance with the regulations may, however, be subject to certain restrictions. Please refer to the
notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this equipment on the market
and has been granted the right to test the series for compliance with the regulations.
Voluntary Control Council for Interference (VCCI) Statement
This equipment is in the second category (information equipment to be used in a residential area or an adjacent area
thereto) and conforms to the standards set by the Voluntary Control Council for Interference by Data Processing
Equipment and Electronic Office Machines aimed at preventing radio interference in such residential areas.
When used near a radio or TV receiver, it may become the cause of radio interference.
Read instructions for correct handling.
Customer Support
Refer to the Support Information Card that shipped with your Wireless Digital Media Player MP115.
World Wide Web
NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL)
http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer or Netscape are
required.
November 2004 202-10038-01
iii
SOFTWARE LICENSE AGREEMENT
1. This Software License Agreement (the “Agreement”) is a legal agreement between you (either an individual or an
entity) (“You
”) and NETGEAR, Inc. (“NETGEAR”) regarding the use of NETGEAR’s software provided with the
Wireless Digital Media Player MP115 (inside the Wireless Digital Media Player MP115, any accompanying CDs,
and any accompanying documentation; together, the “Software”). BEFORE YOU USE THIS SOFTWARE,
CAREFULLY READ THE TERMS AND CONDITIONS OF THIS AGREEMENT. IF YOU ARE NOT
AUTHORIZED TO SIGN, THEN DO NOT DOWNLOAD, INSTALL OR USE THE SOFTWARE, BECAUSE
BY DOING SO, YOU ARE AGREEING TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT AGREE
TO ALL OF THE TERMS OF THIS AGREEMENT, DO NOT DOWNLOAD, INSTALL OR USE THIS
SOFTWARE, AND DESTROY OR RETURN ALL COPIES IN YOUR POSSESSION.
2. Subject to the restrictions set forth below, NETGEAR grants You a nonexclusive, personal, nontransferable,
perpetual (subject to Section 5) license to install and use 1 copy of the provided version of the Software in object
code format, for internal and personal purposes only, on 1 computer. The Software is “in use” on a computer when
it is loaded into the temporary memory or installed into the permanent memory of a computer. The license granted
hereunder shall not be effective until You have paid all fees in full. Except for the license rights granted above,
NETGEAR and NETGEAR’s licensors retain all right, title and interest in and to the Software, including all
intellectual property rights therein. YOU MAY NOT (AND MAY NOT ALLOW A THIRD PARTY TO) (a) RENT,
LEASE, SUBLICENSE, SELL, ASSIGN, LOAN, USE FOR TIMESHARING OR SERVICE BUREAU
PURPOSES OR OTHERWISE TRANSFER THE SOFTWARE OR ANY OF YOUR RIGHTS AND
OBLIGATIONS UNDER THIS AGREEMENT; (b) reverse engineer, decompile, disassemble or attempt to
reconstruct, identify or discover any source code, underlying ideas, underlying user interface techniques or
algorithms of the Software by any means whatsoever, except to the extent the foregoing restrictions are expressly
prohibited by applicable law; (c) remove or destroy any copyright notices or other proprietary markings; (d) attempt
to circumvent any use restrictions; (e) modify or adapt the Software, merge the Software into another program or
create derivative works based on the Software; (f) use, copy or distribute the Software without NETGEAR’s written
authorization, excepting 1 copy for archival or backup purposes only; or (g) use the Software or the Wireless
Digital Media Player MP115 for commercial use. YOU MAY NOT (AND MAY NOT ALLOW A THIRD PARTY
TO) COPY, REPRODUCE, CAPTURE, STORE, RETRANSMIT, DISTRIBUTE, OR BURN TO CD (OR ANY
OTHER FORMAT) ANY COPYRIGHTED CONTENT (INCLUDING BUT NOT LIMITED TO MUSICAL
AND MUSIC-RELATED) THAT YOU ACCESS OR RECEIVE THROUGH USE OF THE SOFTWARE. YOU
ASSUME ALL RISK AND LIABILITY, CIVIL AND CRIMINAL, FOR ANY SUCH PROHIBITED USE OF
COPYRIGHTED CONTENT.
3. THIS AGREEMENT SHALL BE EFFECTIVE UPON INSTALLATION OF THE SOFTWARE AND SHALL
TERMINATE UPON THE EARLIER OF: (A) YOUR FAILURE TO COMPLY WITH ANY TERM OF THIS
AGREEMENT OR (B) RETURN, DESTRUCTION OR DELETION OF ALL COPIES OF THE SOFTWARE IN
YOUR POSSESSION. NETGEAR’s rights and your obligations shall survive any termination of this Agreement.
Upon termination of this Agreement, You shall certify in writing to NETGEAR or such NETGEAR licensor that all
copies of the Software have been destroyed or deleted from any of your computer libraries or storage devices.
4. NETGEAR warrants that the Software will perform substantially in accordance with the documentation
accompanying the Software for a period of 90 days after your initial receipt of the Software. NETGEAR’s entire
liability and your exclusive remedy for breach of this warranty shall be repair or replacement of the Software. This
limited warranty shall be void if failure of the Software has resulted from any accident, abuse, misuse or
misapplication by You. EXCEPT AS SET FORTH ABOVE, THE SOFTWARE IS PROVIDED ON AN “AS IS”
BASIS. YOU ASSUME ALL RESPONSIBILITY FOR SELECTION OF THE SOFTWARE TO ACHIEVE
YOUR INTENDED RESULTS AND FOR THE INSTALLATION OF, USE OF AND RESULTS OBTAINED
FROM THE SOFTWARE. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NETGEAR
DISCLAIMS ALL WARRANTIES, EITHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT
LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT, QUALITY,
ACCURACY, FITNESS FOR A PARTICULAR PURPOSE, AND FITNESS FOR YOUR PURPOSE WITH
RESPECT TO THE SOFTWARE AND THE ACCOMPANYING WRITTEN MATERIALS. THERE IS NO
WARRANTY AGAINST INTERFERENCE WITH THE ENJOYMENT OF THE SOFTWARE OR AGAINST
November 2004 202-10038-01
iv
INFRINGEMENT. NETGEAR DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE
SOFTWARE WILL MEET YOUR REQUIREMENTS, BE UNINTERRUPTED OR ERROR-FREE, OR THAT
ALL DEFECTS IN THE SOFTWARE WILL OR CAN BE CORRECTED.
5. In the event that a claim alleging infringement or misappropriation of an intellectual property right arises
concerning the Software, NETGEAR in its sole discretion may elect to defend or settle such claim. NETGEAR, in
the event of such claim, may also in its sole discretion, elect to terminate this Agreement and all rights to use the
Software and require the return and/or destruction of the Software, with a refund of the fees paid for use of the
Software less a reasonable allowance for use and shipping. THE FOREGOING ARE NETGEAR’S SOLE
EXCLUSIVE OBLIGATIONS, AND YOUR SOLE AND EXCLUSIVE REMEDIES, WITH RESPECT TO
INFRINGEMENT AND/OR MISAPPROPRIATION OF ANY INTELLECTUAL PROPERTY RIGHT.
6. UNDER NO CIRCUMSTANCES WILL NETGEAR OR ITS LICENSORS BE LIABLE FOR ANY
CONSEQUENTIAL, SPECIAL, INDIRECT, INCIDENTAL OR PUNITIVE DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, INTERRUPTION, LOSS OF
BUSINESS INFORMATION, LOSS OF DATA OR OTHER SUCH PECUNIARY LOSS), WHETHER BASED
ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), STRICT LIABILITY, PRODUCT
LIABILITY OR OTHERWISE, ARISING OUT OF THE USE OR INABILITY TO USE THE SOFTWARE,
EVEN IF NETGEAR AND/OR ITS LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN NO EVENT SHALL NETGEAR’S AND ITS LICENSORS’ AGGREGATE LIABILITY FOR
DAMAGES ARISING OUT OF THIS AGREEMENT EXCEED THE FEES PAID BY YOU FOR THE
SOFTWARE. THE FOREGOING LIMITATIONS ARE INDEPENDENT OF THE EXCLUSIVE REMEDY
PROVIDED IN SECTION 6 ABOVE AND SHALL APPLY NOTWITHSTANDING ANY FAILURE OF SUCH
EXCLUSIVE REMEDY OR OF ITS ESSENTIAL PURPOSE. THE FOREGOING EXCLUSIONS AND
LIMITATIONS OF LIABILITY AND DAMAGES SHALL NOT APPLY TO CONSEQUENTIAL DAMAGES
FOR PERSONAL INJURY.
7. You may not export or re-export the Software without: (a) the prior written consent of NETGEAR, (b) complying
with applicable export control laws, including, but not limited to, restrictions and regulations of the Department of
Commerce or other United States agency or authority, and (c) obtaining any necessary permits and licenses. In any
event, You may not transfer or authorize the transfer of the Software to a prohibited territory or country or
otherwise in violation of any applicable restrictions or regulations.
8. The Software and documentation are considered “commercial computer software” and “commercial computer
software documentation,” respectively, pursuant to DFAR Section 227.7202 and FAR Section 12.212, as
applicable. Use, duplication or disclosure of the Software and documentation by the U.S. Government is subject to
the restrictions set forth in DFAR Section 227.7202 for military agencies and FAR Section 12.212 for civilian
agencies. THIS AGREEMENT IS GOVERNED BY THE LAWS OF THE STATE OF CALIFORNIA, U.S.A.,
WITHOUT REFERENCE TO ITS CONFLICT OF LAWS PRINCIPLES. THIS AGREEMENT WILL NOT BE
GOVERNED BY THE U.N. CONVENTION ON CONTRACTS FOR THE INTERNATIONAL SALES OF
GOODS. ANY DISPUTE BETWEEN YOU AND NETGEAR ARISING UNDER THIS AGREEMENT SHALL
BE SUBJECT TO THE EXCLUSIVE JURISDICTION OF THE COURTS OF THE STATE OF CALIFORNIA.
This Agreement is the entire agreement between You and NETGEAR regarding the subject matter herein and
supersedes any other communications with respect to the Software. If any provision of this Agreement is held
invalid or unenforceable, the remainder of this Agreement will continue in full force and effect. Failure to prosecute
a party’s rights with respect to a default hereunder will not constitute a waiver of the right to enforce rights with
respect to the same or any other breach.
9. Should you have any questions relating to this Agreement, or if you desire to contact NETGEAR for any reason,
please call 1-888-NETGEAR.
Contents i
November 2004 202-10038-01
Contents
Chapter 1
About This Manual
Audience, Scope, Conventions, and Formats ................................................................1-1
How to Use This Manual ................................................................................................1-2
How to Print this Manual .................................................................................................1-3
Chapter 2
Introduction
Key Features ..................................................................................................................2-1
Remote Control ..............................................................................................................2-2
Front Panel .....................................................................................................................2-3
Rear Panel ......................................................................................................................2-3
Media Server Software ...................................................................................................2-4
Media Server Software Tabs ....................................................................................2-5
Package Contents ..........................................................................................................2-5
Maintenance and Support ..............................................................................................2-6
Chapter 3
Connecting Your Media Player
Verifying That Basic Requirements Are Met ...................................................................3-1
First, Install the Media Server Software ..................................................................3-2
Then, Install the MP115 Player ................................................................................3-2
Next, Select the Network and Server for the MP115 ................................................3-4
Chapter 4
Videos, Pictures, and Music
Media Formats ................................................................................................................4-1
Media Server Software ...................................................................................................4-1
Media Server Software Tabs ....................................................................................4-2
Watching Videos on Your Television ...............................................................................4-3
Searching Alphabetically with the MP115 Remote Control ............................................4-4
Viewing Pictures .............................................................................................................4-4
November 2004 202-10038-01
ii Contents
Working with Music Files ................................................................................................4-5
My Music Menu ........................................................................................................4-5
Playing All .......................................................................................................................4-6
Playing Albums ...............................................................................................................4-6
Playing Songs by an Artist ..............................................................................................4-6
Playing Songs by Genre .................................................................................................4-7
Playing a Music Playlist ..................................................................................................4-7
Shuffle and Repeat .........................................................................................................4-7
Playing Music from the Internet ......................................................................................4-8
vTuner ......................................................................................................................4-8
Rhapsody .................................................................................................................4-8
Chapter 5
Settings and Maintenance
Settings ...........................................................................................................................5-1
Changing Servers ....................................................................................................5-1
IP Address ................................................................................................................5-1
Available Wireless Networks ....................................................................................5-2
Adding a New Network .............................................................................................5-2
Hidden Networks ......................................................................................................5-3
Manually Setting Wireless Configuration for Hidden Networks ......................................5-3
Specifying the Wireless Location .............................................................................5-4
Setting a Static IP Address .............................................................................................5-4
Video Settings ................................................................................................................5-4
Video Output ............................................................................................................5-5
Changing the Display ...............................................................................................5-7
Upgrading the Wireless Digital Media Player MP115 .....................................................5-7
Chapter 6
Troubleshooting
No Television Display .....................................................................................................6-1
Connecting to the MP115 ...............................................................................................6-1
Physical Connectivity ......................................................................................................6-2
Ethernet Link ............................................................................................................6-2
Wireless Link ............................................................................................................6-2
IP Address ......................................................................................................................6-3
Connecting to the Server ................................................................................................6-3
Contents iii
November 2004 202-10038-01
Connecting to the Rhapsody Server ...............................................................................6-4
Playing Media .................................................................................................................6-4
Firewalls .........................................................................................................................6-5
Glossary
List of Glossary Terms ...................................................................................................G-1
Appendix A
Technical Specifications .................................................................................................... A-1
Appendix B
Wireless Networking Basics
Wireless Networking Overview ...................................................................................... B-1
Infrastructure Mode ................................................................................................. B-1
Ad Hoc Mode (Peer-to-Peer Workgroup) ................................................................ B-2
Network Name: Extended Service Set Identification (ESSID) ................................ B-2
Wireless Channels .................................................................................................. B-2
WEP Wireless Security .................................................................................................. B-4
WEP Authentication ................................................................................................ B-4
WEP Open System Authentication ......................................................................... B-5
WEP Shared Key Authentication ............................................................................ B-6
How to Use WEP Parameters ................................................................................. B-8
WPA Wireless Security .................................................................................................. B-8
How Does WPA Compare to WEP? ........................................................................ B-9
How Does WPA Compare to IEEE 802.11i? ........................................................ B-10
What are the Key Features of WPA Security? ...................................................... B-10
Is WPA Perfect? .................................................................................................... B-16
Product Support for WPA ...................................................................................... B-16
Index
November 2004 202-10038-01
iv Contents
About This Manual 1
November 2004 202-10038-01
Chapter 1
About This Manual
This chapter describes the intended audience, scope, conventions, and formats of this manual. This
manual provides information about using the NETGEAR Wireless Digital Media Player MP115.
See the online help for information about how to use the NETGEAR Media Server software. The
MP115 Installation Guide provides basic setup and installation instructions.
Audience, Scope, Conventions, and Formats
This manual provides information about using the NETGEAR Wireless Digital Media Player
MP115. For information about how to use the NETGEAR Media Server software, run the software
and click Help. See the MP115 Installation Guide for information about installing the software.
This manual assumes that the reader has basic to intermediate computer and Internet skills.
However, basic computer network, Internet, firewall, and digital audio technologies information is
provided in the Appendices and on the NETGEAR Web site.
This guide uses the following typographical conventions:
This guide uses the following formats to highlight special messages:
This manual is written for the MP115 Player according to these specifications:
Table 1-1. Typographical Conventions
italics Emphasis, books, CDs, URL names
bold User input
Note: This format is used to highlight information of importance or special interest.
Table 1-2. Manual Scope
Product Version Wireless Digital Media Player MP115
Manual Publication Date November 2004
User’s Manual for the Wireless Digital Media Player MP115
2 About This Manual
November 2004 202-10038-01
How to Use This Manual
The HTML version of this manual includes a variety of navigation features as well as links to PDF
versions of the full manual and individual chapters.
Figure 1-1: HTML version of this manual
1. Left pane. Use the left pane to view the Contents, Index, Search, and Favorites tabs.
To view the HTML version of the manual, you must have a version 4 or later browser with
JavaScript enabled.
2. Toolbar buttons. Use the toolbar buttons across the top to navigate, print pages, and more.
The Show in Contents button locates the current topic in the Contents tab.
Previous/Next buttons display the previous or next topic.
The PDF button links to a PDF version of the full manual.
The Print button prints the current topic. Click this button when a step-by-step procedure
is displayed to send the entire procedure to your printer. You do not have to worry about
specifying the correct range of pages.
Note: Product updates are available on the NETGEAR Web site at
http://www.netgear.com/support/main.asp.
1
2
3
User’s Manual for the Wireless Digital Media Player MP115
About This Manual 3
November 2004 202-10038-01
3. Right pane. Use the right pane to view the contents of the manual. Also, each page of the
manual includes a link at the top right which links to a PDF file
containing just the currently selected chapter of the manual.
How to Print this Manual
To print this manual you can choose one of the following several options, according to your needs.
Printing a “How To” Sequence of Steps in the HTML View.
Use the Print button on the upper right of the toolbar to print the currently displayed
topic. Using this button when a step-by-step procedure is displayed will send the entire
procedure to your printer--you do not have to worry about specifying the correct range of
pages.
Printing a Chapter.
Use the link at the top right of any page.
Click “PDF of This Chapter” link at the top right of any page in the chapter you want to
print. The PDF version of the chapter you were viewing opens in a browser window.
Note: Your computer must have the free Adobe Acrobat reader installed in order to view
and print PDF files. The Acrobat reader is available on the Adobe Web site at
http://www.adobe.com.
Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.
Printing the Full Manual.
Use the PDF button in the toolbar at the top right of the browser window.
Click the PDF button on the upper right of the toolbar. The PDF version of the
chapter you were viewing opens in a browser window.
Click the print icon in the upper left of the window.
Tip: If your printer supports printing two pages on a single sheet of paper, you can save
paper and printer ink by selecting this feature.
User’s Manual for the Wireless Digital Media Player MP115
4 About This Manual
November 2004 202-10038-01
Introduction 2-1
November 2004 202-10038-01
Chapter 2
Introduction
Congratulations on your purchase of the NETGEAR
®
Wireless Digital Media Player MP115. The
Wireless Digital Media Player MP115 brings the media capabilities of your personal computer to
the comfortable confines of your living room. Now, all the pictures, movies, and music stored in
your computer, as well as streaming Internet radio content can be accessed right from your
television. You can opt for the convenience of current wireless networking standards or the
security and reliability of good old-fashioned wires. NETGEAR’s friendly user interface and
intuitive navigation puts all of your digital content at your fingertips.
The MP115 works with your computer in a client-server system. The MP115 is the client that lets
you browse and play media on your television. The media files are stored on your computer (the
media server) and “served” to the MP115. A network lets the two devices communicate. The
network can either be wired (using the 802.3 Ethernet standard) or wireless (using the 802.11g or
802.11b standard).
Key Features
The MP115 Player provides the following features:
Wireless networking 802.11g or 802.11b, or wired LAN Ethernet.
Easy Media server installation with online help.
Simple menus displayed on your television for MP115 installation and management.
Use the remote to browse selections displayed on your television screen and to listen to music,
watch videos, or view pictures.
Flash memory for firmware upgrades.
Note: This manual provides information on the complete features as of the date of
publication. Go to http://kbserver.netgear.com/products/MP115.asp to find product
firmware updates for your MP115.
User’s Manual for the Wireless Digital Media Player MP115
2-2 Introduction
November 2004 202-10038-01
Remote Control
Use the remote control to navigate menus in the Wireless Digital Media Player MP115 and to
select and view pictures or videos, or listen to music on your television. When using the remote,
aim it at the logo on the right side of the MP115 front panel.
Button Description
Power Icon Power
Navigation
Play
Stop
Rewind
Previous
Pause
Fast forward
Next
OK Select/Play
Home Icon Main menu
i Display media information
Vol +/– Increase or decrease volume
Page +/– Scroll up or down
arrow Mute
Music Music menu
Video Video (Movies) menu
Pics Picture menu
Settings Settings menu
0-9 Numeric entry, presets and search
Disp Sel Display Select: troubleshoot by
cycling through all eight options for
display output.
Shuffle Play the selected media in random
order
Repeat Repeat a track or the entire media
selection
User’s Manual for the Wireless Digital Media Player MP115
Introduction 2-3
November 2004 202-10038-01
Front Panel
The front of the Wireless Digital Media Player MP115 has a light that shows when it is turned on.
The digital logo on the right side shows where to aim the remote when you push buttons.
Figure 2-1: MP115 Front Panel
Rear Panel
The rear panel of the MP115 contains the connectors.
Figure 2-2: MP115 Rear Panel
Viewed from left to right, the rear panel contains the following features:
S-Video port: This type of cable does not ship with the product, and you will need to change
the MP115 settings in order to use it.
Component Video ports: This type of cable is not included, but the MP115 is compatible
with this cable.
Power LED
Aim the remote control here.
Component
SCART
Composite Video
Stereo Audio
S-Video
Ethernet
Power
USB
Reset
Video
(not used)
User’s Manual for the Wireless Digital Media Player MP115
2-4 Introduction
November 2004 202-10038-01
Composite Video and L/R Audio: This type of cable is included, and is compatible with
most televisions in the United States.
SCART: This cable is widely used in Europe and Australia. Though this cable is not included
in the package, the MP115 is set up to be compatible with this cable.
USB: Reserved for future use.
Ethernet: 10/100 Mbps Ethernet port for connecting the media player to a wired LAN (local
area network).
Reset: This button resets the MP115.
Power: The MP115 includes an internal power supply and universal power adapter.
Media Server Software
The Wireless Digital Media Player MP115 comes with Media Server software that runs on a
computer on your home network. The Media Server software is easily installed from the Resource
CD. During installation, the Media Server scans the network for media files, which are then
available for MP115 to play. After installation, it automatically starts when that computer is
powered on. You may use the Media Server to scan for additional media at any time.
User’s Manual for the Wireless Digital Media Player MP115
Introduction 2-5
November 2004 202-10038-01
Media Server Software Tabs
The Media Server software includes detailed online help, which is not included in this manual. The
Media Server software includes five tabs:
Media Files tab: Scan computers on the network to locate media files, which you can then
play on the MP115 Player.
Media Import tab: Import Plugins and scan for media files, which you can then play on the
MP115 Player.
Options tab: Specify file types to scan. Display media files.
System tab: Manage network settings such as the Server Name. View Media Server status,
and statistics.
Premium Services tab: Manage Internet radio.
Package Contents
The product package should contain the following items:
Wireless Digital Media Player MP115.
Remote control (2AA batteries included).
Power cable, localized to country of sale.
Category 5 (CAT5) Ethernet cable.
Composite Video cable and Audio cable.
NETGEAR Wireless Digital Media Player MP115 Resource CD , including:
This guide.
The Installation Guide.
Application Notes and other helpful information.
Wireless Media Player MP115 Installation Guide.
Warranty/Support Information card.
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the router for repair.
User’s Manual for the Wireless Digital Media Player MP115
2-6 Introduction
November 2004 202-10038-01
Maintenance and Support
NETGEAR offers the following features to help you maximize your use of the MP115 Player:
Flash memory for firmware upgrades.
Free technical support seven days a week, 24 hours a day, for 90 days from the date of
purchase.
Connecting Your Media Player 3-1
November 2004 202-10038-01
Chapter 3
Connecting Your Media Player
This chapter describes how to set up the Wireless Digital Media Player MP115 on your local area
network (LAN).
Verifying That Basic Requirements Are Met
Make sure that you have the following:
A wireless (802.11b or 802.11g) or Ethernet network
One or more computers running Windows 98SE, 2000, ME or XP
Television set
Broadband Internet service (recommended)
Have your Network Name (SSID) and security settings handy.
Firewalls can interfere with or block MP115 performance. If you are running Windows XP
Service Pack 2, then during installation the NETGEAR Wireless Digital Media Player MP115
Resource CD sets the firewall up to be compatible. If you use other firewalls, such as
ZoneAlarm, set the following ports to be open:
UDP Ports: 1360, 1900
TCP Ports: 1025 – 1035, 3640, 3641, 4000, 4001, 7000 – 7010, 49200 – 49210
Also see the Media Server software online Firewall topic.
User’s Manual for the Wireless Digital Media Player MP115
3-2 Connecting Your Media Player
November 2004 202-10038-01
First, Install the Media Server Software
1. Power on your computer and log in as needed.
2. Insert the Resource CD into the CD drive on
the computer. The CD main page loads.
3. Follow the InstallShield Wizard steps and
click Finish when done.
Note: Depending on your location,
complimentary 30-day trials for Internet radio
stations may be available for vTuner and
Rhapsody. The Resource CD automatically
installs vTuner. To use the trial for Rhapsody,
you must also select INSTALL RHAPSODY
Digital Music Service and complete that
installation.
4. Restart your computer and the NETGEAR Media Server software automatically runs. The
Media Server software icon appears on the Windows System Tray.
5. Use the Media Server software to scan your hard drive to locate your video, picture, and music
files. For more information, see “Media Server Software Tabs” on page 4-2, Chapter 4.
Note: You can use the Options tab on the Media Server to specify which types of files you
want to include, as described in the Media Server online help.
Then, Install the MP115 Player
1. Determine which type of cable your television uses:
Video cable and Audio cable: These two cables are included, and are compatible with
most televisions in the U.S.
SCART: This cable is often used in Europe and Australia, and is not included in the
package. However, if you have a SCART cable the MP115 will recognize it, and you can
continue to use these instructions.
S-Video, or Component Video: These cables are not included in the package. If you use
this type of cabling you will be prompted to select video output settings when the MP115
first starts up.
User’s Manual for the Wireless Digital Media Player MP115
Connecting Your Media Player 3-3
November 2004 202-10038-01
2. For composite video, connect the supplied video cable and audio cable to the Composite Video
and Stereo Audio ports on the back of the MP115.
Figure 3-1: MP115 rear view, cable connections
If you are supplying your own SCART, S-Video, or Component Video cable, connect it (and
the audio cable if applicable) to the corresponding port on the back of the MP115.
3. Connect the other end of the cables to the corresponding ports on your television.
Figure 3-2: Wireless home network with MP115 and television
4. If you have a wired LAN network (not wireless), use an Ethernet cable such as the one
provided in the package to connect the MP115 to your router.
5. Install the two AA batteries into the remote control that shipped with the product.
Component Video
SCART
Composite Video
Stereo Audio
S-Video
jÄÍ¬Ë+ËÝÍ
ja?ËwjÄ
Á?aM?a
aj
ÍjÁjÍ
8ÁjjÄÄË-ÖÍjÁËÄÖWË?Ä
?Ë!jÍ~j?ÁË.Ö¬jÁË
8ÁjjÄÄË-ÖÍjÁ
~Í?Ë ÖÄWË+?ßjÁË +¤å¤
DIGITAL
+¤¤yË~Í?Ë ja?Ë
+?ßjÁ
User’s Manual for the Wireless Digital Media Player MP115
3-4 Connecting Your Media Player
November 2004 202-10038-01
Next, Select the Network and Server for the MP115
Warning: The MP115 includes an internal power supply and universal power adapter. NETGEAR
strongly recommends that you confirm the power requirements for your local jurisdiction before
you utilize the power cord supplied with the product.
1. Make sure that the MP115 Media Server software is running.
Note: The Media Server software automatically runs when you restart your computer, and this
icon appears on the Windows System Tray.
2. Turn on the television.
3. Connect the MP115 power cord and plug it into an outlet.
The LED on the front of the MP115 lights up to show that it is powered on. The logo on the
lower right corner of the MP115 shows where to aim the remote control.
The MP115 start-up screen appears on the television screen as shown below:
Figure 3-3: Start-up screen shown on the television
The MP115 automatically performs the following tasks:
Checking Hardware
Finding Network
Getting IP Address
•Finding Server
Accessing Media
User’s Manual for the Wireless Digital Media Player MP115
Connecting Your Media Player 3-5
November 2004 202-10038-01
Note: If you have connected an S-Video or Component Video cable, and if the MP115 is not
configured to generate output to its S-Video or Component Video ports, then you may see a
flickering image or no image on your television screen. The MP115 executes its power on
routine in the background.
To fix this problem, push Disp Sel on the remote control to cycle through all video output
options and select the correct one.
4. If your network is wireless and/or uses security settings, the MP115 stops at Finding Network,
and goes to the Settings: Available Networks screen.
The MP115 is set from the factory to get its IP Address from a DHCP server. If your
network does not use DHCP, you must set up the MP115 with a Static IP Address in
the range of addresses on your network.
If the MP115 is set to use DHCP and fails to obtain an IP Address from the server, it
will resort to an auto IP Address in the range of 169.254.x.x. You can use a Static IP
Address if there is a problem connecting the MP115 to the server.
5. Use the remote control to enter your wireless and security settings.
Then the main menu appears as shown below:
Figure 3-4: Main menu displayed on the television screen
All the files that you scanned with the Media Server software are now available to play on the
Wireless Digital Media Player MP115. Use the remote control to select the desired media.
Note: If the MP115 does not connect to the network, it displays the Settings: Network menu. Use
the remote to browse and select an Available Network from the onscreen display. For more
information, see “Connecting to the MP115” on page 6-1, Chapter 4.
User’s Manual for the Wireless Digital Media Player MP115
3-6 Connecting Your Media Player
November 2004 202-10038-01
Videos, Pictures, and Music 4-1
November 2004 202-10038-01
Chapter 4
Videos, Pictures, and Music
Media Formats
To play media, the MP115 must be connected to the network, and the Media Server software must
be running. To scan for digital files, go to the computer running the Media Server software and use
the Media tab and Media Import tab. The files may be stored on any computer on the network, or
on a CD in the computers CD drive.
The Wireless Digital Media Player MP115 is compatible with the following media file formats:
MPEG 1, 2, 4 compressed audio and video files
JPEG and GIF compressed image files
BMP and TIFF image files
MP3s up to 320 Kbps or variable bit rate (VBR)
WMA8 and WMA9 files up to 192Kbps or variable bit rate (VBR)
•WAV audio files
Internet Radio (streaming MP3)
Playlist Formats:
—M3U
PLS
Media Server Software
The Media Server software is easily installed from the Resource CD as described in Chapter 3,
“First, Install the Media Server Software ” on page 3-2. After installation, it automatically starts
when that computer is powered on. The Media Server software icon appears on the Windows
System Tray.
User’s Manual for the Wireless Digital Media Player MP115
4-2 Videos, Pictures, and Music
November 2004 202-10038-01
Media Server Software Tabs
The Media Server software has detailed online help, which is not included in this manual. The
Media Server software features are grouped onto five tabs:
Media Files tab: Scan
computers on the
network to locate media
files, which you can then
play on the MP115
Player.
Media Import tab:
Import Plugins and scan
for media files to play on
the MP115 Player.
User’s Manual for the Wireless Digital Media Player MP115
Videos, Pictures, and Music 4-3
November 2004 202-10038-01
Options tab: Specify file
types to scan. Display
media files.
System tab: Manage network settings such as the Server Name. View Media Server status,
and statistics.
Premium Services tab: Manage Internet radio.
Watching Videos on Your Television
Before the MP115 can play videos, you must use the Media server software running on your
computer to scan and locate your media files. If you want to include media files that are stored on
other computers, external hard drives, or other storage devices on the network, make sure to select
them when you scan.
Note: You can use the Video Settings menu to set the TV Aspect Ratio, Video Mode, or Video
Output. See “Setting the TV Aspect Ratio” on page 5-4.
Use the remote control to select My Video from the Main menu displayed on the television. The
Video menu displays the following options:
All: List all available video files in alphabetical order.
Albums: List video files by album.
Video Show: The video show allows you to combine two or more video files into a single
show. This is useful when you have a movie that is stored on your computer as several files.
User’s Manual for the Wireless Digital Media Player MP115
4-4 Videos, Pictures, and Music
November 2004 202-10038-01
Note: To display information about the video, push i on the remote control. This option is only
available when a movie is listed or playing:
Searching Alphabetically with the MP115 Remote Control
Any list of content can be searched alphabetically using the alphanumeric keypad on the remote
control. This technique is useful for quickly finding an desired selection in a long list of items.
To search a listing alphabetically:
1. Navigate to the directory that contains the desired item.
2. Press the button on the alphanumeric keypad that corresponds to the first letter of the desired
item. Pressing each button will cycle through the letters and number printed on the button. For
example, pressing 5 will cycle through J-K-L-5.
3. Continue entering additional letters or numbers. Use the
or button to backspace. The
alphabetic search is not case sensitive.
4. Press OK
to execute the search. The window will scroll to the first item that matches the
search criteria.
Viewing Pictures
Before you can view pictures with the MP115, you must use the Media server software running on
your computer to scan and locate your media files. If you want to include media files that are
stored on other computers, external hard drives, or other storage devices on the network, make
sure to select them when you scan.
Use the Pics button on the remote control, or select My Pictures from the Main menu to go to the
Pictures menu. The Pictures menu shows the following selections:
All: Show all the digital photographs in alphabetical order, by file name. Select the desired
photographs to view.
Albums: View photographs by albums.
Slideshow: View all photographs in a selected directory. The MP115 automatically displays
one photo after the other. To adjust the length of time each picture is shown for a Slideshow,
see
“Setting the Slideshow Time” on page 5-2.
Note: You can browse photos by List View or by Thumbnail View; and with or without Previews.
To customize these settings, see “Changing the Display” on page 5-1.
User’s Manual for the Wireless Digital Media Player MP115
Videos, Pictures, and Music 4-5
November 2004 202-10038-01
Working with Music Files
Before the MP115 can play music, you must use the Media server software running on your
computer to scan and locate your media files. If you want to include media files that are stored on
other computers, external hard drives, or other storage devices on the network, make sure to select
them when you scan.
Some audio files may be stored without information in some fields, such as album or genre. If this
is the case, these tracks are listed in a category called “Unknown”. Internet Radio selections are
listed under the Premium Content selection on the main menu. See “Playing Music from the
Internet” on page 4-8.
My Music Menu
You can use the Music button on the remote to go to the Music menu, or select My Music from the
main menu displayed on your television. The Music menu appears as shown below:
Figure 4-1: Music menu displayed on the television screen
The Music menu offers the following selections:
All
•Albums
Artists
•Genres
Music Playlist
User’s Manual for the Wireless Digital Media Player MP115
4-6 Videos, Pictures, and Music
November 2004 202-10038-01
Playing All
1. Select All from the Music menu.
The tracks are listed in alphabetical order.
2. Scroll to the desired album. To fast scroll, hold down the Up or Down arrows for three
seconds. The Left or Right arrows also fast scroll at a faster rate. To perform an alphabetic
search see “Shuffle and Repeat” on page 4-7.
3. Push the Repeat button on the remote and an icon appears on the lower right of the television
screen. Use this button to cycle through three options: all tracks (arrow), one track (1), or play
and repeat all (two curved arrows).
Playing Albums
You can play an entire album, or a specific song in the album.
1. Select Albums from the Music menu.
The albums are listed in alphabetical order.
2. Scroll to the desired album. To fast scroll, hold down the Up or Down arrows for three
seconds. The Left or Right arrows also fast scroll at a faster rate. To perform an alphabetic
search see “Shuffle and Repeat” on page 4-7.
3. Push the Repeat button on the remote and an icon appears on the lower right of the television
screen. Use this button to cycle through three options: all tracks (arrow), one track (1), or play
and repeat all (two curved arrows).
Playing Songs by an Artist
1. Select Artist from the Music menu.
The artists are listed alphabetically.
2. Scroll through the list and select the desired artist. To fast scroll, hold down the Up or Down
arrows for three seconds. The Left or Right arrows also fast scroll at a faster rate. To perform
an alphabetic search see “Shuffle and Repeat” on page 4-7.
3. Push the Repeat button on the remote and an icon appears on the lower right of the television
screen. Use this button to cycle through three options: all tracks (arrow), one track (1), or play
and repeat all (two curved arrows).
User’s Manual for the Wireless Digital Media Player MP115
Videos, Pictures, and Music 4-7
November 2004 202-10038-01
Playing Songs by Genre
1. Select Genre from the Music menu.
The genres that are listed depend on the media files that are on your media server or Internet
music server. Some formats, such as MP3 include genre. If a music file does not contain a
genre, it is listed as Unknown, at the end of the list of genres.
2. Scroll to the desired genre. To fast scroll, hold down the Up or Down arrow for three seconds.
The Left or Right arrows also fast scroll at a faster rate. To perform an alphabetic search see
“Shuffle and Repeat” on page 4-7.
3. Push the Repeat button on the remote and an icon appears on the lower right of the television
screen. Use this button to cycle through four options: genre (musical note), all tracks (arrow),
one track (1), or play and repeat all (two curved arrows).
Playing a Music Playlist
1. Select Music Playlist from the Music menu.
2. Scroll to the desired playlist and select it.
3. Push the Repeat button on the remote and an icon appears on the lower right of the television
screen. Use this button to cycle through the options: music playlist (musical note), all tracks
(arrow), or one track (1).
Shuffle and Repeat
Shuffle mode plays the selected songs in random order. Repeat lets you repeat a track or the entire
selection that you are playing.
Press the Shuffle button on the remote control to toggle Shuffle mode on and off. When Shuffle is
on, an icon appears on the lower right corner of the television.
Press the Repeat button on the remote control to cycle through Repeat modes.
User’s Manual for the Wireless Digital Media Player MP115
4-8 Videos, Pictures, and Music
November 2004 202-10038-01
Playing Music from the Internet
vTuner
vTuner lists thousands of Internet Radio stations from over 100 countries around the globe. You
can use the Wireless Digital Media Player MP115 to play Internet Radio from vTuner. The vTuner
Basic Internet Radio Guide includes a limited number of stations and is included at no charge with
your MP115. vTuner Super Guide includes a much larger list of stations and is available for an
additional charge. You can sign up for vTuner Super Guide at http://www.radio1234.com. You can
go to this Web site by clicking the Radio1234.com button on the Options tab of the NETGEAR
Media Server software.
The Radio1234.com station list is customized for the MP115 and contains only stations that are
broadcast in formats it can support.
To play a vTuner Internet Radio station:
1. Select Premium Content from the Main menu.
2. Select Internet Radio.
You can use the options displayed on the television screen to search for radio stations by
Genre, Countries, New Stations or Popular Stations.
Note: You can also select from stations in the My Favorites list. The My Favorites selection
will not appear until you have selected radio stations at http://www.radio1234.com. This URL
can be accessed by clicking the Radio1234.com button under the Options tab of the
NETGEAR Media Server software.
3. Select an option, and then scroll and select the tracks you would like to play.
Rhapsody
Note: Rhapsody Digital Music Service is available only in the United States.
The Wireless Digital Media Player MP115 can play music over the Internet from Rhapsody Digital
Music Service. The Rhapsody service runs on its own server software, which must be installed on
your computer in addition to the NETGEAR Media Server Software. After installation you can use
the MP115 to select the Rhapsody server. You will have access to all the tracks, albums, playlists
and digital radio stations on the My Library tab in your Rhapsody account.
User’s Manual for the Wireless Digital Media Player MP115
Videos, Pictures, and Music 4-9
November 2004 202-10038-01
To play Rhapsody Internet radio station:
1. If you do not already have a Rhapsody account, use the Resource CD to install the free 30-day
trial account on a computer that is on your home network.
2. Access your Rhapsody account.
Note: Be sure that UPnP Server is enabled in the Rhapsody application. This setting can be
found in the Options, User Settings menu item, under the UPnP tab. The UPnP Server will be
enabled by default if Rhapsody is installed from the Resource CD.
3. Go to the MP115 and push the Settings button on the remote control.
The Settings menu displays on the television.
4. Select Servers.
5. Select the Rhapsody server. You will receive a message confirming the connection.
All the music from the My Library folder on the Rhapsody server is now accessible from the
Wireless Digital Media Player MP115. You can access this music by artist, album, tracks,
playlists or radio stations.
6. Select Premium Service from the main menu displayed on your television.
7. Select Rhapsody.
8. Scroll and select the tracks you would like to play.
Note: The Rhapsody server may not support all of the features that are available on the
NETGEAR Media Server software.
User’s Manual for the Wireless Digital Media Player MP115
4-10 Videos, Pictures, and Music
November 2004 202-10038-01
Settings and Maintenance 5-1
November 2004 202-10038-01
Chapter 5
Settings and Maintenance
This chapter describes how to use the configuration and maintenance features of your Wireless
Digital Media Player MP115.
Note: If you want to change network settings or options for the Media Server software, use the
Media Server Options tab and Media Server System tab as described in the Media Server online
help.
Settings
Press the Settings button on the remote control. The Settings menu offers the following selections:
Servers: Select an available media server or music server.
Network: Configure your wired or wireless network connection.
Video: Set your preferred video display format, video outputs and aspect ratio.
Display: Set your language preferences, list view settings, Slideshow timing, and screen saver.
Maintenance: Search for and install the latest firmware.
Help: Basic network and player help.
Changing Servers
1. From the Settings menu, select Servers.
2. The MP115 searches for servers. You can use the Refresh button at the bottom of the television
screen to update the display.
3. Select the server that you want to use.
IP Address
The Wireless Digital Media Player MP115 is set by default to get its IP Address via DHCP. With
this setting, the DHCP server on your network assigns the IP Address to the MP115, which is a is a
client. If your network does not use DHCP, then you must set the IP Address for the MP115 to be
in the correct subnet range for your network.
User’s Manual for the Wireless Digital Media Player MP115
5-2 Settings and Maintenance
November 2004 202-10038-01
1. Push the Settings button on the remote.
2. Select Network, and then select IP Address.
The screen shows DCHP and Static. The MP115 ships set up to use DCHP.
3. Select an option and view the IP Address, Subnet Mask, Network Type, and Network Name.
Available Wireless Networks
1. Push the Settings button on the remote.
2. Select Network, and then select Wireless.
3. Select Available Networks.
The screen shows the following information about the available networks:
Name: The Network Name (SSID)
Channel: The channel that the wireless access point is using.
Mode: AP (Access Point) is the normal setting.
Security: The default is Disabled.
Signal: Good, fair, or poor.
4. If you want to change to another network, select the network.
Note: Networks that do not broadcast their SSID may not appear on this screen. For
information about working with hidden networks see “Hidden Networks” on page 5-3. Also
see “Wireless Link” on page 6-2.
5. Select Apply and push OK.
Adding a New Network
1. Push the Settings button on the remote.
2. From the Settings menu, select Wireless.
3. Select New/Hidden Networks.
You are prompted to enter your wireless network SSID (up to 32 characters).
4. Enter the network name (SSID), select Next and push OK
5. Select New for the network type.
6. Select the security level.
User’s Manual for the Wireless Digital Media Player MP115
Settings and Maintenance 5-3
November 2004 202-10038-01
The default setting is Disabled. To accept this setting, select NEXT; or press the UP arrow to
select WEP mode and specify the key size.
Hidden Networks
Use this option if you want the MP115 to look for a network that does not broadcast its SSID.
1. Push the Settings button on the remote.
2. From the Settings menu, select Wireless.
3. Select New/Hidden Networks.
The MP115 sends a message to check for hidden networks and also looks for new networks.
4. Check the display on the television screen to see if the network is now listed on the Available
Networks screen.
Manually Setting Wireless Configuration for Hidden
Networks
Note: Detailed background information about wireless networking can be found in Appendix B,
“Wireless Networking Basics”.
In order to configure the MP115 to work in a network where the SSID broadcast is disabled, you
must manually configure the wireless settings. Also, it may be necessary to manually configure an
Ad Hoc network.
To configure wireless settings manually:
1. Push the Settings button on the remote.
2. Select Network, and then select Wireless.
3. From the Wireless menu, select New/Hidden Network.
The current wireless settings, if any, are displayed in the second row for your reference.
4. Press OK to accept the setting or press X to change the setting. Enter a value of up to 32
alphanumeric characters for the SSID. After entering the new SSID, press OK to save.
The Wireless Mode is displayed.
5. Press OK to accept the setting or press X to change the setting. Options for wireless mode are
Infrastructure and Ad/Hoc. If Ad/Hoc is chosen, you will also need to choose a location along
with a wireless channel.
User’s Manual for the Wireless Digital Media Player MP115
5-4 Settings and Maintenance
November 2004 202-10038-01
6. The WEP Security screen will now be displayed. Detailed instructions for configuring WEP
can be found in Appendix B, “Wireless Networking Basics”.
7. The system reboots and connects to the selected wireless network.
Specifying the Wireless Location
You can specify the country where your wireless network operates.
1. Push Settings on the remote control to go to the Settings menu.
2. From the Settings menu, select Network, and then select Wireless.
3. Select Location, and choose the correct location for your network.
4. Click Apply to save the setting.
Setting a Static IP Address
The MP115 is set up to use DHCP. With DHCP, the MP115 get its IP address from a DHCP server
on the network. If your network does not use DHCP, then you need to change the MP115 settings
to a Static IP Address, and set the IP Address to a subnet within the correct range for your network.
1. Push Settings on the remote control to go to the Settings menu.
2. From the Settings menu, select Network, and then select IP Address.
The Settings: Network:IP Address screen appears.
3. Select Static.
4. Use the number buttons on the remote control to enter the IP Address. Use the OK button to
save each number and move to the next field.
5. After the IP address is set, enter the subnet mask.
Video Settings
Use the Video Settings menu to set the TV Aspect Ratio, Video Mode, or Video Output.
Setting the TV Aspect Ratio
You can set the Aspect Ratio to Letter Box, Full Screen, or 4:3.
1. Push the Settings button on the remote to go to the Settings menu.
User’s Manual for the Wireless Digital Media Player MP115
Settings and Maintenance 5-5
November 2004 202-10038-01
2. Select Video.
3. Select TV Aspect Ratio.
4. Use the navigation buttons on the remote control to display the desired setting.
5. Select Apply, and push OK on the remote control.
Setting the Video Mode
Set the Video Mode to NTSC, or PAL.
1. Push the Settings button on the remote to go to the Settings menu.
2. Select Video.
3. Select Video Mode.
4. Use the navigation buttons on the remote control to display the desired setting.
5. Select Apply, and push OK on the remote control.
Video Output
Note: If you select the wrong Video Output, then you may not be able to see the menus on the
television. To correct this problem, push the Disp Sel button on the remote control. You can cycle
through each of the eight possible video modes to find and select the correct one.
You can choose S-Video, SCART, Component Progressive, or Component Interlaced.
S-Video: This cable is not included in the package. If your television uses S-Video, you must
provide your own cable and set the Video Output to S-Video.
SCART: This cable is often used in Europe and Australia, and is not included in the package.
However, if you have a SCART cable the MP115 will recognize it.
Component Progressive and Component Interlaced: The MP115 is set by default to work
with component video cables. To use component progressive you must have a television that
supports this technology.
Changing the Video Output Settings
1. Push the Settings button on the remote to go to the Settings menu.
2. Select Video.
3. Select Video Output.
4. Use the navigation buttons on the remote control to display the desired setting.
User’s Manual for the Wireless Digital Media Player MP115
5-6 Settings and Maintenance
November 2004 202-10038-01
5. Select Apply, and push OK on the remote control.
User’s Manual for the Wireless Digital Media Player MP115
Settings and Maintenance 5-7
November 2004 202-10038-01
Changing the Display
1. Push the Settings button on the remote to go to the Settings menu.
2. From the Settings menu, select Display.
3. The Display menu offers the following selections:
Photo/Video Browsing: Choose List View or Thumbnail View.
Previews: On or Off.
Language on Screen: Choose English, German, or French.
Setting the Slideshow Time: Set the length of time that each picture is displayed during a
Slideshow. The Slideshow time may be set to 5 seconds, 8 seconds, or 10 seconds, as
explained below.
Selecting the Screen Saver: Toggle between Floating Logo and Blank Screen.
Setting the Slideshow Time
Set the length of time that each picture is displayed during a Slideshow. The Slideshow time can be
set to 5 seconds, 8 seconds, or 10 seconds.
1. Push the Settings button on the remote to go to the Settings menu.
2. From the Settings menu, select Display.
3. Select Slideshow Time.
4. Use the navigation buttons on the remote control to display the desired setting.
5. Select Apply, and push OK on the remote control.
Upgrading the Wireless Digital Media Player MP115
Warning: Do not play media on the Wireless Digital Media Player MP115 during the upgrade.
1. On the computer that runs the Media Server software, download new firmware from the
http://www.NETGEAR.com support site.
2. Run the firmware installer program, as described in the firmware release notes.
3. Go to the MP115 and push the Settings button on the remote to display the Settings menu.
4. Select Upgrade Firmware.
The television screen shows the Current Firmware Version and lists Available Upgrades.
User’s Manual for the Wireless Digital Media Player MP115
5-8 Settings and Maintenance
November 2004 202-10038-01
5. If there is an upgrade available, select it.
6. Select Apply Upgrade and push OK on the remote control.
The unit reboots and reconnects to the last network used.
Troubleshooting 6-1
November 2004 202-10038-01
Chapter 6
Troubleshooting
This chapter gives information about troubleshooting your Wireless Digital Media Player MP115.
After each problem description, instructions are provided to help you diagnose and solve the
problem.
No Television Display
If the wrong video output is set on the MP115 then the television display will not work. Push the
Disp Sel button on the remote control to cycle through the video output settings. When you have
reached the correct setting, the television display will work. Select that setting and push OK on the
remote control.
Connecting to the MP115
Here are some tips for correcting simple problems that may prevent you from connecting to the
media player.
Problem Recommended Action
MP115 does not respond
to the remote control.
Check the LED on the front panel of the MP115 to make sure
the power is on.
Make sure the television is turned on.
Aim the remote control at the logo on the upper right of the
MP115.
The LED on the remote control should flash when you push a
button.
If the LED does not flash, and the batteries are
working, then the remote may be faulty.
If the LED does flash, reset the MP115
MP115 does not find my
network.
Make sure the Wireless Network Name (SSID) and
WEP settings of the MP115 and media server match
exactly.
Restart the media server software, then power cycle the
MP115.
User’s Manual for the Wireless Digital Media Player MP115
6-2 Troubleshooting
November 2004 202-10038-01
Physical Connectivity
Ethernet Link
Because the MP115 incorporates Auto Uplink technology (also called Auto MDI/MDI-X), it is
capable of automatically sensing the polarity of the Ethernet connection. You can therefore
connect using either a standard or crossover Ethernet cable. The Ethernet port of your MP115 will
automatically configure itself properly.
If connecting to your network using Ethernet, the link LED on the back of your MP115 and on
your hub or router should both be on. If not, try the following:
Make sure that the Ethernet cable connections are secure at the router and at the hub or
workstation.
Make sure that power is turned on to the connected hub or workstation.
Wireless Link
Please be aware that wireless data rate and throughput decreases as the distance increases between
the Access Point (AP) and the MP115 Player. If you are unable to detect any wireless networks, try
the following:
Your wireless AP (access point) may be too far from the MP115. It may be necessary to move
either the AP or the MP115 so that they are closer together.
If you are using a wireless connection between the AP (or wireless router) and the computer
that serves the media content, you might also need to move the computer and the AP closer
together.
MP115 does not find the
server.
Make sure your computer is running the media server
software.
If you wish to use Rhapsody, make sure that the media
server is running Rhapsody, and that Rhapsody is the
selected server for the
MP115.
Computer firewall software can prevent the media
server from communicating with the
MP115. See the
Firewall topic in the media server online help.
If you do not use DHCP on your network, you must set
the IP address of the
MP115 in the range of addresses on
your network. See IP Address on page 6-3.
User’s Manual for the Wireless Digital Media Player MP115
Troubleshooting 6-3
November 2004 202-10038-01
If your access point is configured to disable broadcast of SSID, the MP115 will not be able to
detect it. You will need to manually configure your wireless settings as described in
“Manually
Setting Wireless Configuration for Hidden Networks” on page 5-6.
The MP115 cannot connect to the wireless network while it is connected to the Ethernet
network. Disconnect your Ethernet cable.
IP Address
If the MP115 is unable to receive a valid IP address, try the following:
Verify that a working DHCP server is on your network. PCs on the network should get IP
addresses in the correct range.
If you are using a wireless network, verify that the MP115 is associated with the correct SSID.
The SSID that is being used can be displayed by following instructions in
“Manually Setting
Wireless Configuration for Hidden Networks” on page 5-6.
If you are using a wireless network, verify that the WEP settings on the MP115 match the
settings on your access point. Instructions for setting WEP can be found in
Appendix B,
“Wireless Networking Basics. If you are using a passphrase, note that it is case-sensitive.
Using the WEP Wizard you can view the hex key generated by the passphrase algorithm
directly. This must match the setting on your access point.
Connecting to the Server
If the MP115 cannot find the correct server, try the following:
Verify that the NETGEAR Media Server is running on your PC. You should be able to see the
icon in the system tray. If it is not on the network, there will be a red bar through the icon.
Verify that the MP115 and the PC running the Media Server software are on the same subnet
and that they can communicate with each other. In most cases, this means that the first three
fields of the two IP address should be the same. Communication can be verified using the
Windows Ping utility.
1. From the Windows toolbar, click on the Start button and select Run.
2. In the field provided, type ping followed by the IP address of the MP115. Displaying the
IP address is described in IP Address on page 5-2.
PING 192.168.0.2
User’s Manual for the Wireless Digital Media Player MP115
6-4 Troubleshooting
November 2004 202-10038-01
3. Click OK. You should see a message like this one:
PINGING <IP ADDRESS> WITH 32 BYTES OF DATA
If the path is working, you see this message:
REPLY FROM < IP ADDRESS >: BYTES=32 TIME=NN MS TTL=XXX
If the path is not working, you see this message:
REQUEST TIMED OUT
4. If you cannot ping the MP115 your network may not be working correctly.
The Status Bar of the NETGEAR Media Server, which can be found at the bottom of the
window, should show “Media Player is on the network.” If the Status Bar shows “Media
Server is not on network!”, verify that your PC has a valid IP address and that the correct
adapter is chosen. The adapter is chosen using the Change Adapter button under the System
tab.
If multiple adapters are installed in your PC, the Media Server software can only monitor one
of them at a time. Verify that the correct adapter is chosen. The adapter is chosen using the
Change Adapter button under the System tab.
Connecting to the Rhapsody Server
If the MP115 cannot find your Rhapsody server, try the following:
The Rhapsody application must be running on your PC. This application is different from the
NETGEAR Media Server.
Verify that the version of the Rhapsody server installed supports UPnP and that the UPnP
server is running. The Rhapsody application shipped on the NETGEAR Wireless Digital Media
Player MP115 Resource CD supports UPnP and has the server running by default after
installation. The status of the Rhapsody UPnP server can be displayed in the Options menu,
User Settings selection under the UPnP tab. The Start UPnP Server once logged in box
should be selected and the Status should indicate Running.
Playing Media
If the MP115 cannot play media or music from the NETGEAR Media Server; or music from the
Rhapsody server, try the following:
Check to see if the file is protected. The MP115 cannot play protected files.
User’s Manual for the Wireless Digital Media Player MP115
Troubleshooting 6-5
November 2004 202-10038-01
Verify that the file is not corrupt by double-clicking it in the Media Files tab on the Media
Server.
If you are running personal firewall software it may block access to music on your PC. See
Firewalls on page 6-5.
If you are playing from a Rhapsody server, verify that the My Library folder is not empty.
The MP115 can only play music from the My Library folder.
Firewalls
If you are using a firewall, it is best if all of your devices are behind the firewall. If this is not
possible, then the next best alternative is to open the ports required for NETGEAR Streaming
Media to work. Please note that the latter alternative will reduce some of the protection afforded
by the firewall, but is necessary for streaming media devices to work. The ports that must be open
include:
UDP Ports: 1360, 1900.
TCP Ports: 1025 – 1035, 3640, 3641, 4000, 4001, 7000 – 7010, 49200 – 49210.
Personal Firewall products can also interfere with the MP115 operation. Detailed instructions for
configuring personal firewall products can be found by clicking Help in the NETGEAR Media
Server software under the Troubleshooting section.
User’s Manual for the Wireless Digital Media Player MP115
6-6 Troubleshooting
November 2004 202-10038-01
November 2004 202-10038-01
Glossary
1
Glossary
Use the list below to find definitions for technical terms used in this manual.
List of Glossary Terms
10BASE-T
IEEE 802.3 specification for 10 Mbps Ethernet over twisted pair wiring.
100BASE-Tx
IEEE 802.3 specification for 100 Mbps Ethernet over twisted pair wiring.
802.1x
802.1x defines port-based, network access control used to provide authenticated network access and
automated data encryption key management.
The IEEE 802.1x draft standard offers an effective framework for authenticating and controlling user traffic
to a protected network, as well as dynamically varying encryption keys. 802.1x uses a protocol called EAP
(Extensible Authentication Protocol) and supports multiple authentication methods, such as token cards,
Kerberos, one-time passwords, certificates, and public key authentication. For details on EAP specifically,
refer to IETF's RFC 2284.
802.11a
IEEE specification for wireless networking at 54 Mbps operating in unlicensed radio bands over 5GHz.
802.11b
IEEE specification for wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS)
technology and operating in the unlicensed radio spectrum at 2.5GHz.
802.11g
A soon to be ratified IEEE specification for wireless networking at 54 Mbps using direct-sequence
spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.5GHz. 802.11g is
backwards compatible with 802.11b.
ADSL
Short for asymmetric digital subscriber line, a technology that allows data to be sent over existing copper
telephone lines at data rates of from 1.5 to 9 Mbps when receiving data (known as the downstream rate) and
from 16 to 640 Kbps when sending data (known as the upstream rate).
User’s Manual for the Wireless Digital Media Player MP115
2 Glossary
November 2004 202-10038-01
ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world
gain access.
AES
Advanced Encryption Standard, a symmetric 128-bit block data encryption technique.
It is an iterated block cipher with a variable block length and a variable key length. The block length and the
key length can be independently specified to 128, 192 or 256 bits.The U.S government adopted the
algorithm as its encryption technique in October 2000, replacing the DES encryption it used. AES works at
multiple network layers simultaneously.
ARP
Address Resolution Protocol, a TCP/IP protocol used to convert an IP address into a physical address (called
a DLC address), such as an Ethernet address.
A host wishing to obtain a physical address broadcasts an ARP request onto the TCP/IP network. The host
on the network that has the IP address in the request then replies with its physical hardware address. There is
also Reverse ARP (RARP) which can be used by a host to discover its IP address. In this case, the host
broadcasts its physical address and a RARP server replies with the host's IP address.
Auto Uplink
Auto Uplink
TM
technology (also called MDI/MDIX) eliminates the need to worry about crossover vs.
straight-through Ethernet cables. Auto Uplink
TM
will accommodate either type of cable to make the right
connection.
Cat 5
Category 5 unshielded twisted pair (UTP) cabling. An Ethernet network operating at 10 Mbits/second
(10BASE-T) will often tolerate low quality cables, but at 100 Mbits/second (10BASE-Tx) the cable must be
rated as Category 5, or Cat 5 or Cat V, by the Electronic Industry Association (EIA).
This rating will be printed on the cable jacket. Cat 5 cable contains eight conductors, arranged in four
twisted pairs, and terminated with an RJ45 type connector. In addition, there are restrictions on maximum
cable length for both 10 and 100 Mbits/second networks.
Denial of Service attack
DoS. A hacker attack designed to prevent your computer or network from operating or communicating.
DHCP
An Ethernet protocol specifying how a centralized DHCP server can assign network configuration
information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and
gateway (router) addresses.
The DMZ sits between the Internet and an internal network's line of defense, usually some combination of
firewalls and bastion hosts. Typically, the DMZ contains devices accessible to Internet traffic, such as Web
(HTTP) servers, FTP servers, SMTP (e-mail) servers and DNS servers.
User’s Manual for the Wireless Digital Media Player MP115
Glossary
3
November 2004 202-10038-01
DNS
Short for Domain Name System (or Service), an Internet service that translates domain names into IP
addresses.
Because domain names are alphabetic, they're easier to remember. The Internet however, is really based on
IP addresses. Every time you use a domain name, therefore, a DNS service must translate the name into the
corresponding IP address. For example, the domain name www.example.com might translate to
198.105.232.4. The DNS system is, in fact, its own network. If one DNS server doesn't know how to
translate a particular domain name, it asks another one, and so on, until the correct IP address is returned.
Domain Name
A descriptive name for an address or group of addresses on the Internet. Domain names are of the form of a
registered entity name plus one of a number of predefined top level suffixes such as .com, .edu, .uk, etc. For
example, in the address mail.NETGEAR.com, mail is a server name and NETGEAR.com is the domain.
DSL
Short for digital subscriber line, but is commonly used in reference to the asymmetric version of this
technology (ADSL) that allows data to be sent over existing copper telephone lines at data rates of from 1.5
to 9 Mbps when receiving data (known as the downstream rate) and from 16 to 640 Kbps when sending data
(known as the upstream rate).
ADSL requires a special ADSL modem. ADSL is growing in popularity as more areas around the world
gain access.
DSLAM
DSL Access Multiplexor. The piece of equipment at the telephone company central office that provides the
ADSL signal.
Dynamic Host Configuration Protocol
DHCP. An Ethernet protocol specifying how a centralized DHCP server can assign network configuration
information to multiple DHCP clients. The assigned information includes IP addresses, DNS addresses, and
gateway (router) addresses.
EAP
Extensible Authentication Protocol is a general protocol for authentication that supports multiple
authentication methods.
EAP, an extension to PPP, supports such authentication methods as token cards, Kerberos, one-time
passwords, certificates, public key authentication and smart cards. In wireless communications using EAP, a
user requests connection to a WLAN through an AP, which then requests the identity of the user and
transmits that identity to an authentication server such as RADIUS. The server asks the AP for proof of
identity, which the AP gets from the user and then sends back to the server to complete the authentication.
EAP is defined by RFC 2284.
ESSID
The Extended Service Set Identification (ESSID) is a thirty-two character (maximum) alphanumeric key
identifying the wireless local area network.
User’s Manual for the Wireless Digital Media Player MP115
4 Glossary
November 2004 202-10038-01
Gateway
A local device, usually a router, that connects hosts on a local network to other networks.
IETF
Internet Engineering Task Force. Working groups of the IETF propose standard protocols and procedures for
the Internet, which are published as RFCs (Request for Comment) at
www.ietf.org.
An open international community of network designers, operators, vendors, and researchers concerned with
the evolution of the Internet architecture and the smooth operation of the Internet.
IP
Internet Protocol is the main internetworking protocol used in the Internet. Used in conjunction with the
Transfer Control Protocol (TCP) to form TCP/IP.
IP Address
A four-byte number uniquely defining each host on the Internet, usually written in dotted-decimal notation
with periods separating the bytes (for example, 134.177.244.57).
Ranges of addresses are assigned by Internic, an organization formed for this purpose.
ISP
Internet service provider.
Internet Protocol
The main internetworking protocol used in the Internet. Used in conjunction with the Transfer Control
Protocol (TCP) to form TCP/IP.
LAN
A communications network serving users within a limited area, such as one floor of a building.
local area network
LAN. A communications network serving users within a limited area, such as one floor of a building.
A LAN typically connects multiple personal computers and shared network devices such as storage and
printers. Although many technologies exist to implement a LAN, Ethernet is the most common for
connecting personal computers.
MAC address
The Media Access Control address is a unique 48-bit hardware address assigned to every network interface
card. Usually written in the form 01:23:45:67:89:ab.
Mbps
Megabits per second.
MDI/MDIX
In cable wiring, the concept of transmit and receive are from the perspective of the PC, which is wired as a
Media Dependant Interface (MDI). In MDI wiring, a PC transmits on pins 1 and 2. At the hub, switch,
User’s Manual for the Wireless Digital Media Player MP115
Glossary
5
November 2004 202-10038-01
router, or access point, the perspective is reversed, and the hub receives on pins 1 and 2. This wiring is
referred to as Media Dependant Interface - Crossover (MDI-X). See also AES.
NAT
A technique by which several hosts share a single IP address for access to the Internet.
Network Address Translation
NAT. A technique by which several hosts share a single IP address for access to the Internet.
NIC
Network Interface Card. An adapter in a computer which provides connectivity to a network.
packet
A block of information sent over a network. A packet typically contains a source and destination network
address, some protocol and length information, a block of data, and a checksum.
RFC
Request For Comment. Refers to documents published by the Internet Engineering Task Force (IETF)
proposing standard protocols and procedures for the Internet. RFCs can be found at www.ietf.org.
router
A device that forwards data between networks. An IP router forwards data based on IP source and
destination addresses.
SSID
A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless
local area network. For the wireless devices in a network to communicate with each other, all devices must
be configured with the same SSID.
This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the
wireless Access Point and to the wireless network name. See also Wireless Network Name and ESSID.
Subnet Mask
A mask used to determine what subnet an IP address belongs to. Subnetting enables a network administrator
to further divide an IP address into two or more subnets.
An IP address has two components, the network address and the host address. For example, consider the IP
address 150.215.017.009. Assuming this is part of a Class B network, the first two numbers (150.215)
represent the Class B network address, and the second two numbers (017.009) identify a particular host on
this network.
Subnetting enables the network administrator to further divide the host part of the address into two or more
subnets. In this case, a part of the host address is reserved to identify the particular subnet. This is easier to
see if we show the IP address in binary format. The full address is: 10010110.11010111.00010001.00001001
The Class B network part is: 10010110.11010111
and the host address is 00010001.00001001
User’s Manual for the Wireless Digital Media Player MP115
6 Glossary
November 2004 202-10038-01
If this network is divided into 14 subnets, however, then the first 4 bits of the host address (0001) are
reserved for identifying the subnet.
The subnet mask is the network address plus the bits reserved for identifying the subnetwork. (By
convention, the bits for the network address are all set to 1, though it would also work if the bits were set
exactly as in the network address.) In this case, therefore, the subnet mask would be
11111111.11111111.11110000.00000000. It's called a mask because it can be used to identify the subnet to
which an IP address belongs by performing a bitwise AND operation on the mask and the IP address. The
result is the subnetwork address: Subnet Mask 255.255.240.000 11111111.11111111.11110000.00000000
IP Address 150.215.017.009 10010110.11010111.00010001.00001001
Subnet Address 150.215.016.000 10010110.11010111.00010000.00000000
The subnet address, therefore, is 150.215.016.000.
TCP/IP
The main internetworking protocols used in the Internet. The Internet Protocol (IP) used in conjunction with
the Transfer Control Protocol (TCP) form TCP/IP.
Universal Plug and Play
UPnP. A networking architecture that provides compatibility among networking technology. UPnP
compliant routers provide broadband users at home and small businesses with a seamless way to participate
in online games, videoconferencing and other peer-to-peer services.
UTP
Unshielded twisted pair is the cable used by 10BASE-T and 100BASE-Tx Ethernet networks.
WAN
A long distance link used to extend or connect remotely located local area networks. The Internet is a large
WAN.
WEB Proxy Server
A Web proxy server is a specialized HTTP server that allows clients access to the Internet from behind a
firewall.
The proxy server listens for requests from clients within the firewall and forwards these requests to remote
Internet servers outside the firewall. The proxy server reads responses from the external servers and then
sends them to internal client clients.
WEP
Wired Equivalent Privacy is a data encryption protocol for 802.11b wireless networks.
All wireless nodes and access points on the network are configured with a 64-bit or 128-bit Shared Key for
data encryption.
User’s Manual for the Wireless Digital Media Player MP115
Glossary
7
November 2004 202-10038-01
wide area network
WAN. A long distance link used to extend or connect remotely located local area networks. The Internet is a
large WAN.
Wi-Fi
A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility
Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among
802.11b devices.
Windows Internet Naming Service
WINS. Windows Internet Naming Service is a server process for resolving Windows-based computer names
to IP addresses.
If a remote network contains a WINS server, your Windows PCs can gather information from that WINS
server about its local hosts. This allows your PCs to browse that remote network using the Windows
Network Neighborhood feature.
WINS
WINS. Windows Internet Naming Service is a server process for resolving Windows-based computer names
to IP addresses.
Wireless Network Name (SSID)
Wireless Network Name (SSID) is the name assigned to a wireless network. This is the same as the SSID or
ESSID configuration parameter.
User’s Manual for the Wireless Digital Media Player MP115
8 Glossary
November 2004 202-10038-01
Technical Specifications A-1
November 2004 202-10038-01
Appendix A
Technical Specifications
This appendix provides technical specifications for the Wireless Digital Media Player MP115.
Network Protocol and Standards Compatibility
Data and Routing Protocols: TCP/IP, DHCP
Power Adapter
North America: 120V, 60 Hz, input
United Kingdom, Australia: 240V, 50 Hz, input
Europe: 230V, 50 Hz, input
Japan: 100V, 50/60 Hz, input
All regions (output): 12 V DC @ 1A output, 22W maximum
Physical Specifications
Dimensions: (H x W x D): 244 x 271 x 221 mm (1.4 x 10.7 x 8.7 in.)
Weight: 1.2 kg (2.6 lbs)
Environmental Specifications
Operating temperature: 0° to 40° C (32º to 104º F)
Operating humidity: 90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Meets requirements of: FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
C-Tick N10947
Interface Specifications
LAN: 10BASE-T or 100BASE-Tx, RJ-45
WAN: 10BASE-T or 100BASE-Tx, RJ-45
Wireless
User’s Manual for the Wireless Digital Media Player MP115
A-2 Technical Specifications
November 2004 202-10038-01
Radio Data Rates 1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, and 54 Mbps
Auto Rate Sensing
Frequency 2.4-2.5Ghz
Data Encoding: 802.11b: Direct Sequence Spread Spectrum (DSSS)
802.11g: Orthogonal Frequency Division Multiplexing (OFDM)
Maximum Computers Per Wireless
Network:
Limited by the amount of wireless network traffic generated by each
node. Typically 30-70 nodes.
Operating Frequency Ranges: 2.412~2.462 GHz (US) 2.457~2.462 GHz (Spain)
2.412~2.484 GHz (Japan)2.457~2.472 GHz (France)
2.412~2.472 GHz (Europe ETSI)
802.11 Security: 40-bit (also called 64-bit) and 128-bit WEP and WPA-PSK
1
1
WPA-PSK may not be supported in the orginal product release.
Wireless Networking Basics B-1
November 2004 202-10038-01
Appendix B
Wireless Networking Basics
Wireless Networking Overview
The MP115 Player conforms to the Institute of Electrical and Electronics Engineers (IEEE)
802.11g standard for wireless LANs (WLANs). On an 802.11 wireless link, data is encoded using
direct-sequence spread-spectrum (DSSS) technology and is transmitted in the unlicensed radio
spectrum at 2.5GHz. The maximum data rate for the 802.11g wireless link is 54 Mbps, but it will
automatically back down from 54 Mbps when the radio signal is weak or when interference is
detected.
The 802.11 standard is also called Wireless Ethernet or Wi-Fi by the Wireless Ethernet
Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standard group promoting
interoperability among 802.11 devices. The 802.11 standard offers two methods for configuring a
wireless network—ad hoc and infrastructure.
Infrastructure Mode
With a wireless access point, you can operate the wireless LAN in the infrastructure mode. This
mode provides wireless connectivity to multiple wireless network devices within a fixed range or
area of coverage, interacting with wireless nodes via an antenna.
In the infrastructure mode, the wireless access point converts airwave data into wired Ethernet
data, acting as a bridge between the wired LAN and wireless clients. Connecting multiple access
points via a wired Ethernet backbone can further extend the wireless network coverage. As a
mobile computing device moves out of the range of one access point, it moves into the range of
another. As a result, wireless clients can freely roam from one access point domain to another and
still maintain seamless network connection.
User’s Manual for the Wireless Digital Media Player MP115
B-2 Wireless Networking Basics
November 2004 202-10038-01
Ad Hoc Mode (Peer-to-Peer Workgroup)
In an ad hoc network, computers are brought together as needed; thus, there is no structure or fixed
points to the network—each node can generally communicate with any other node. There is no
access point involved in this configuration. This mode enables you to quickly set up a small
wireless workgroup and allows workgroup members to exchange data or share printers as
supported by Microsoft networking in the various Windows operating systems. Some vendors also
refer to ad hoc networking as peer-to-peer group networking.
In this configuration, network packets are directly sent and received by the intended transmitting
and receiving stations. As long as the stations are within range of one another, this is the easiest
and least expensive way to set up a wireless network.
Network Name: Extended Service Set Identification (ESSID)
The Extended Service Set Identification (ESSID) is one of two types of Service Set Identification
(SSID). In an ad hoc wireless network with no access points, the Basic Service Set Identification
(BSSID) is used. In an infrastructure wireless network that includes an access point, the ESSID is
used, but may still be referred to as SSID.
An SSID is a thirty-two character (maximum) alphanumeric key identifying the name of the
wireless local area network. Some vendors refer to the SSID as network name. For the wireless
devices in a network to communicate with each other, all devices must be configured with the
same SSID.
Wireless Channels
IEEE 802.11g/b wireless nodes communicate with each other using radio frequency signals in the
ISM (Industrial, Scientific, and Medical) band between 2.4 GHz and 2.5 GHz. Neighboring
channels are 5 MHz apart. However, due to spread spectrum effect of the signals, a node sending
signals using a particular channel will utilize frequency spectrum 12.5 MHz above and below the
center channel frequency. As a result, two separate wireless networks using neighboring channels
(for example, channel 1 and channel 2) in the same general vicinity will interfere with each other.
Applying two channels that allow the maximum channel separation will decrease the amount of
channel cross-talk, and provide a noticeable performance increase over networks with minimal
channel separation.
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-3
November 2004 202-10038-01
The radio frequency channels used are listed in Table B-1:
Note: The available channels supported by the wireless products in various countries are different.
The preferred channel separation between the channels in neighboring wireless networks is 25
MHz (5 channels). This means that you can apply up to three different channels within your
wireless network. There are only 11 usable wireless channels in the United States. It is
recommended that you start using channel 1 and grow to use channel 6, and 11 when necessary, as
these three channels do not overlap.
Table B-1. 802.11g Radio Frequency Channels
Channel Center Frequency Frequency Spread
1 2412 MHz 2399.5 MHz - 2424.5 MHz
2 2417 MHz 2404.5 MHz - 2429.5 MHz
3 2422 MHz 2409.5 MHz - 2434.5 MHz
4 2427 MHz 2414.5 MHz - 2439.5 MHz
5 2432 MHz 2419.5 MHz - 2444.5 MHz
6 2437 MHz 2424.5 MHz - 2449.5 MHz
7 2442 MHz 2429.5 MHz - 2454.5 MHz
8 2447 MHz 2434.5 MHz - 2459.5 MHz
9 2452 MHz 2439.5 MHz - 2464.5 MHz
10 2457 MHz 2444.5 MHz - 2469.5 MHz
11 2462 MHz 2449.5 MHz - 2474.5 MHz
12 2467 MHz 2454.5 MHz - 2479.5 MHz
13 2472 MHz 2459.5 MHz - 2484.5 MHz
User’s Manual for the Wireless Digital Media Player MP115
B-4 Wireless Networking Basics
November 2004 202-10038-01
WEP Wireless Security
The absence of a physical connection between nodes makes the wireless links vulnerable to
eavesdropping and information theft. To provide a certain level of security, the IEEE 802.11
standard has defined two types of authentication methods, Open System and Shared Key. With
Open System authentication, a wireless computer can join any network and receive any messages
that are not encrypted. With Shared Key authentication, only those computers that possess the
correct authentication key can join the network. By default, IEEE 802.11 wireless devices operate
in an Open System network. Recently, Wi-Fi, the Wireless Ethernet Compatibility Alliance
(http://www.wi-fi.net) developed the Wi-Fi Protected Access (WPA), a new strongly enhanced
Wi-Fi security. WPA will soon be incorporated into the IEEE 802.11 standard. WEP and WPA are
discussed below.
WEP Authentication
The 802.11 standard defines several services that govern how two 802.11 devices communicate.
The following events must occur before an 802.11 Station can communicate with an Ethernet
network through an access point such as the one built in to the MP115:
1. Turn on the wireless station.
2. The station listens for messages from any access points that are in range.
3. The station finds a message from an access point that has a matching SSID.
4. The station sends an authentication request to the access point.
5. The access point authenticates the station.
6. The station sends an association request to the access point.
7. The access point associates with the station.
8. The station can now communicate with the Ethernet network through the access point.
An access point must authenticate a station before the station can associate with the access point or
communicate with the network. The IEEE 802.11 standard defines two types of WEP
authentication: Open System and Shared Key.
Open System Authentication allows any device to join the network, assuming that the device
SSID matches the access point SSID. Alternatively, the device can use the “ANY” SSID
option to associate with any available access point within range, regardless of its SSID.
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-5
November 2004 202-10038-01
Shared Key Authentication requires that the station and the access point have the same WEP
Key to authenticate. These two authentication procedures are described below.
WEP Open System Authentication
This process is illustrated below.
Figure B-1: 802.11 open system authentication
The following steps occur when two devices use Open System Authentication:
1. The station sends an authentication request to the access point.
2. The access point authenticates the station.
3. The station associates with the access point and joins the network.
INTERNET LOCAL
ACT
12345678
LNK
LNK/ACT
100
Cable/DSL
ProSafeWirelessVPN SecurityFirewall
MODEL
FVM318
PWR TEST
WLAN
Enable
Access Point (AP)
1) Authentication request sent to AP
2) AP authenticates
3) Client connects to network
Open System
Authentication Steps
Cable or
DLS modem
Client
attempting
to connect
User’s Manual for the Wireless Digital Media Player MP115
B-6 Wireless Networking Basics
November 2004 202-10038-01
WEP Shared Key Authentication
This process is illustrated below.
Figure B-2: 802.11 shared key authentication
The following steps occur when two devices use Shared Key Authentication:
1. The station sends an authentication request to the access point.
2. The access point sends challenge text to the station.
3. The station uses its configured 64-bit or 128-bit default key to encrypt the challenge text, and
sends the encrypted text to the access point.
4. The access point decrypts the encrypted text using its configured WEP key that corresponds to
the station’s default key. The access point compares the decrypted text with the original
challenge text. If the decrypted text matches the original challenge text, then the access point
and the station share the same WEP key and the access point authenticates the station.
5. The station connects to the network.
If the decrypted text does not match the original challenge text (i.e., the access point and station do
not share the same WEP key), then the access point will refuse to authenticate the station and the
station will be unable to communicate with either the 802.11 network or Ethernet network.
INTERNET LOCAL
ACT
12345678
LNK
LNK/ACT
100
Cable/DSL
ProSafeWirelessVPN SecurityFirewall
MODEL
FVM318
PWR TEST
WLAN
Enable
Access Point1) Authentication
request sent to AP
2) AP sends challenge text
3) Client encrypts
challenge text and
sends it back to AP
4) AP decrypts, and if correct,
authenticates client
5) Client connects to network
Shared Key
Authentication Steps
Cable or
DLS modem
Client
attempting
to connect
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-7
November 2004 202-10038-01
Key Size and Configuration
The IEEE 802.11 standard supports two types of WEP encryption: 40-bit and 128-bit.
The 64-bit WEP data encryption method, allows for a five-character (40-bit) input. Additionally,
24 factory-set bits are added to the forty-bit input to generate a 64-bit encryption key. (The 24
factory-set bits are not user-configurable). This encryption key will be used to encrypt/decrypt all
data transmitted via the wireless interface. Some vendors refer to the 64-bit WEP data encryption
as 40-bit WEP data encryption since the user-configurable portion of the encryption key is 40 bits
wide.
The 128-bit WEP data encryption method consists of 104 user-configurable bits. Similar to the
40-bit WEP data encryption method, the remaining 24 bits are factory set and not user
configurable. Some vendors allow passphrases to be entered instead of the cryptic hexadecimal
characters to ease encryption key entry.
The 128-bit encryption is stronger than 40-bit encryption, but 128-bit encryption may not be
available outside of the United States due to U.S. export regulations.
When configured for 40-bit encryption, 802.11 products typically support up to four WEP keys.
Each 40-bit WEP Key is expressed as five sets of two hexadecimal digits (0-9 and A-F). For
example, “12 34 56 78 90” is a 40-bit WEP key.
When configured for 128-bit encryption, 802.11g products typically support four WEP keys but
some manufacturers support only one 128-bit key. The 128-bit WEP Key is expressed as 13 sets of
two hexadecimal digits (0-9 and A-F). For example, “12 34 56 78 90 AB CD EF 12 34 56 78 90”
is a 128-bit WEP key.
Typically, 802.11 access points can store up to four 128-bit WEP Keys but some 802.11 client
adapters can only store one. Therefore, make sure that your 802.11 access and client adapters
configurations match.
Whatever keys you enter for an access point, you must also enter the same keys for the client
adapter in the same order. In other words, WEP key 1 on the AP must match WEP key 1 on the
client adapter, WEP key 2 on the AP must match WEP key 2 on the client adapter, etc.
Note: The access point and the client adapters can have different default WEP keys as long as the
keys are in the same order. In other words, the AP can use WEP key 2 as its default key to transmit
while a client adapter can use WEP key 3 as its default key to transmit. The two devices will
communicate as long as the access point’s WEP key 2 is the same as the client’s WEP key 2 and
the AP’s WEP key 3 is the same as the client’s WEP key 3.
User’s Manual for the Wireless Digital Media Player MP115
B-8 Wireless Networking Basics
November 2004 202-10038-01
How to Use WEP Parameters
Wired Equivalent Privacy (WEP) data encryption is used when the wireless devices are configured
to operate in Shared Key authentication mode. There are two shared key methods implemented in
most commercially available products, 64-bit and 128-bit WEP data encryption.
Before enabling WEP on an 802.11 network, you must first consider what type of encryption you
require and the key size you want to use. Typically, there are three WEP Encryption options
available for 802.11 products:
1. Do Not Use WEP: The 802.11 network does not encrypt data. For authentication purposes, the
network uses Open System Authentication.
2. Use WEP for Encryption: A transmitting 802.11 device encrypts the data portion of every
packet it sends using a configured WEP Key. The receiving 802.11g device decrypts the data using
the same WEP Key. For authentication purposes, the 802.11g network uses Open System
Authentication.
3. Use WEP for Authentication and Encryption: A transmitting 802.11 device encrypts the data
portion of every packet it sends using a configured WEP Key. The receiving 802.11 device
decrypts the data using the same WEP Key. For authentication purposes, the 802.11 network uses
Shared Key Authentication.
Note: Some 802.11 access points also support Use WEP for Authentication Only (Shared Key
Authentication without data encryption). However, the MP115 does not offer this option.
WPA Wireless Security
Wi-Fi Protected Access (WPA) is a specification of standards-based, interoperable security
enhancements that increase the level of data protection and access control for existing and future
wireless LAN systems.
The IEEE introduced the WEP as an optional security measure to secure 802.11g (Wi-Fi) WLANs,
but inherent weaknesses in the standard soon became obvious. In response to this situation, the
Wi-Fi Alliance announced a new security architecture in October 2002 that remedies the short
comings of WEP. This standard, formerly known as Safe Secure Network (SSN), is designed to
work with existing 802.11 products and offers forward compatibility with 802.11i, the new
wireless security architecture being defined in the IEEE.
WPA offers the following benefits:
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-9
November 2004 202-10038-01
Enhanced data privacy
Robust key management
Data origin authentication
Data integrity protection
Starting in August of 2003, all new Wi-Fi certified products had to support WPA and all existing
Wi-Fi certified products had one year to comply with the new standard or lose their Wi-Fi
certification. NETGEAR has implemented WPA on client and access point products. As of August
2004, all Wi-Fi certified products must support WPA.
How Does WPA Compare to WEP?
WEP is a data encryption method and is not intended as a user authentication mechanism. WPA
user authentication is implemented using 802.1x and the Extensible Authentication Protocol
(EAP). Support for 802.1x authentication is required in WPA. In the 802.11 standard, 802.1x
authentication was optional. For details on EAP specifically, refer to IETF's RFC 2284.
With 802.11 WEP, all access points and client wireless adapters on a particular wireless LAN must
use the same encryption key. A major problem with the 802.11 standard is that the keys are
cumbersome to change. If you don't update the WEP keys often, an unauthorized person with a
sniffing tool can monitor your network for less than a day and decode the encrypted messages.
Products based on the 802.11 standard alone offer system administrators no effective method to
update the keys.
For 802.11, WEP encryption is optional. For WPA, encryption using Temporal Key Integrity
Protocol (TKIP) is required. TKIP replaces WEP with a new encryption algorithm that is stronger
than the WEP algorithm, but that uses the calculation facilities present on existing wireless devices
to perform encryption operations. TKIP provides important data encryption enhancements
including a per-packet key mixing function, a message integrity check (MIC) named Michael, an
extended initialization vector (IV) with sequencing rules, and a re-keying mechanism. Through
these enhancements, TKIP addresses all of known WEP vulnerabilities.
User’s Manual for the Wireless Digital Media Player MP115
B-10 Wireless Networking Basics
November 2004 202-10038-01
How Does WPA Compare to IEEE 802.11i?
WPA is forward compatible with the IEEE 802.11i security specification currently under
development. WPA is a subset of the current 802.11i draft and uses certain pieces of the 802.11i
draft that were ready to bring to market in 2003, such as 802.1x and TKIP. The main pieces of the
802.11i draft that are not included in WPA are secure IBSS (Ad-Hoc mode), secure fast handoff
(for specialized 802.11 VoIP phones), as well as enhanced encryption protocols such as
AES-CCMP. These features are either not yet ready for market or will require hardware upgrades
to implement.
What are the Key Features of WPA Security?
The following security features are included in the WPA standard:
WPA Authentication
WPA Encryption Key Management
Temporal Key Integrity Protocol (TKIP)
Michael message integrity code
(MIC)
AES Support
Support for a Mixture of WPA and WEP Wireless Clients
These features are discussed below.
WPA addresses most of the known WEP vulnerabilities and is primarily intended for wireless
infrastructure networks as found in the enterprise. This infrastructure includes stations, access
points, and authentication servers (typically RADIUS servers). The RADIUS server holds (or has
access to) user credentials (e.g., user names and passwords) and authenticates wireless users
before they gain access to the network.
The strength WPA comes from an integrated sequence of operations that encompass 802.1X/EAP
authentication and sophisticated key management and encryption techniques. Its major operations
include:
Network security capability determination. This occurs at the 802.11 level and is
communicated through WPA information elements in Beacon, Probe Response, and (Re)
Association Requests. Information in these elements includes the authentication method
(802.1X or Pre-shared key) and the preferred cipher suite (WEP, TKIP, or AES).
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-11
November 2004 202-10038-01
The primary information conveyed in the Beacon frames is the authentication method and the
cipher suite. Possible authentication methods include 802.1X and Pre-shared key. Pre-shared
key is an authentication method that uses a statically configured passphrase on both the
stations and the access point. This removes the need for an authentication server, which in
many home and small office environments will not be available nor desirable. Possible cipher
suites include: WEP, TKIP, and AES (Advanced Encryption Standard). We’ll talk more TKIP
and AES when addressing data privacy below.
Authentication. EAP over 802.1X is used for authentication. Mutual authentication is
gained by choosing an EAP type supporting this feature and is required by WPA. The 802.1X
port access control prevents full access to the network until authentication completes. The
802.1X EAPOL-Key packets are used by WPA to distribute per-session keys to those stations
successfully authenticated.
The supplicant in the station uses the authentication and cipher suite information contained in
the information elements to decide which authentication method and cipher suite to use. For
example, if the access point is using the Pre-shared key method then the supplicant need not
authenticate using full-blown 802.1X. Rather, the supplicant must simply prove to the access
point that it is in possession of the pre-shared key. If the supplicant detects that the service set
does not contain a WPA information element then it knows it must use pre-WPA 802.1X
authentication and key management in order to access the network.
Key management. WPA features a robust key generation/management system that integrates
the authentication and data privacy functions. Keys are generated after successful
authentication and through a subsequent four-way handshake between the station and access
point (AP).
Data Privacy (Encryption). Temporal Key Integrity Protocol (TKIP) is used to wrap WEP in
sophisticated cryptographic and security techniques to overcome most of its weaknesses.
Data integrity. TKIP includes a message integrity code (MIC) at the end of each plain text
message to ensure messages are not being spoofed.
User’s Manual for the Wireless Digital Media Player MP115
B-12 Wireless Networking Basics
November 2004 202-10038-01
WPA Authentication: Enterprise-level User
Authentication via 802.1x/EAP and RADIUS
Figure B-3: WPA Overview
IEEE 802.1x offers an effective framework for authenticating and controlling user traffic to a
protected network, as well as providing a vehicle for dynamically varying data encryption keys via
EAP from a RADIUS server, for example. This framework enables using a central authentication
server, which employs mutual authentication so that a rogue wireless user does not join the
network.
It's important to note that 802.1x doesn't provide the actual authentication mechanisms. When
using 802.1x, the EAP type, such as Transport Layer Security (EAP-TLS) or EAP Tunneled
Transport Layer Security (EAP-TTLS) defines how the authentication takes place.
Note: For environments with a Remote Authentication Dial-In User Service (RADIUS)
infrastructure, WPA supports Extensible Authentication Protocol (EAP). For environments
without a RADIUS infrastructure, WPA supports the use of a preshared key.
Together, these technologies provide a framework for strong user authentication.
Windows XP implements 802.1x natively, and several NETGEAR switch and wireless access
point products support 802.1x.
WPA
enabled
wireless
client with
“supplicant”
Certificate
Authority
(eg Win
Server,
VeriSign,
etc)
TCP/IP
Ports Closed
Until
RADIUS Server
Wired Network with Optional
802.1x Port Based Network
Access Control
WPA enabled
Access Point
using
pre-shared key
or
802.1x
TCP/IP
Ports Opened
After
Authenticated
Wireless LAN
Login
Authentication
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-13
November 2004 202-10038-01
Figure B-4: 802.1x Authentication Sequence
The access point (AP) sends Beacon Frames with WPA information elements to the stations in the
service set. Information elements include the required authentication method (802.1x or
Pre-shared key) and the preferred cipher suite (WEP, TKIP, or AES). Probe Responses (AP to
station) and Association Requests (station to AP) also contain WPA information elements.
1. Initial 802.1x communications begin with an unauthenticated supplicant (i.e., client device)
attempting to connect with an authenticator (i.e., 802.11 access point). The client sends an
EAP-start message. This begins a series of message exchanges to authenticate the client.
2. The access point replies with an EAP-request identity message.
1
2
3
4
56
7
Client with a WPA-
enabled wireless
adapter and supplicant
(Win XP, Funk,
Meetinghouse, etc.)
For example, a
WPA-enabled AP
For example, a
RADIUS server
User’s Manual for the Wireless Digital Media Player MP115
B-14 Wireless Networking Basics
November 2004 202-10038-01
3.
The client sends an EAP-response packet containing the identity to the authentication server.
The access point responds by enabling a port for passing only EAP packets from the client to
an authentication server located on the wired side of the access point. The access point blocks
all other traffic, such as HTTP, DHCP, and POP3 packets, until the access point can verify the
client's identity using an authentication server (e.g., RADIUS).
4. The authentication server uses a specific authentication algorithm to verify the client's identity.
This could be through the use of digital certificates or some other EAP authentication type.
5. The authentication server will either send an accept or reject message to the access point.
6. The access point sends an EAP-success packet (or reject packet) to the client.
7. If the authentication server accepts the client, then the access point will transition the client's
port to an authorized state and forward additional traffic.
The important part to know at this point is that the software supporting the specific EAP type
resides on the authentication server and within the operating system or application “supplicant”
software on the client devices. The access point acts as a “pass through” for 802.1x messages,
which means that you can specify any EAP type without needing to upgrade an 802.1x-compliant
access point. As a result, you can update the EAP authentication type to such devices as token
cards (Smart Cards), Kerberos, one-time passwords, certificates, and public key authentication or
as newer types become available and your requirements for security change.
WPA Data Encryption Key Management
With 802.1x, the rekeying of unicast encryption keys is optional. Additionally, 802.11 and 802.1x
provide no mechanism to change the global encryption key used for multicast and broadcast
traffic. With WPA, rekeying of both unicast and global encryption keys is required.
For the unicast encryption key, the Temporal Key Integrity Protocol (TKIP) changes the key for
every frame, and the change is synchronized between the wireless client and the wireless access
point (AP). For the global encryption key, WPA includes a facility (the Information Element) for
the wireless AP to advertise the changed key to the connected wireless clients.
If configured to implement dynamic key exchange, the 802.1x authentication server can return
session keys to the access point along with the accept message. The access point uses the session
keys to build, sign and encrypt an EAP key message that is sent to the client immediately after
sending the success message. The client can then use contents of the key message to define
applicable encryption keys. In typical 802.1x implementations, the client can automatically change
encryption keys as often as necessary to minimize the possibility of eavesdroppers having enough
time to crack the key in current use.
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-15
November 2004 202-10038-01
Temporal Key Integrity Protocol (TKIP)
WPA uses TKIP to provide important data encryption enhancements including a per-packet key
mixing function, a message integrity check (MIC) named Michael, an extended initialization
vector (IV) with sequencing rules, and a re-keying mechanism. TKIP also provides for the
following:
The verification of the security configuration after the encryption keys are determined.
The synchronized changing of the unicast encryption key for each frame.
The determination of a unique starting unicast encryption key for each preshared key
authentication.
Michael
With 802.11 and WEP, data integrity is provided by a 32-bit integrity check value (ICV) that is
appended to the 802.11 payload and encrypted with WEP. Although the ICV is encrypted, you can
use cryptanalysis to change bits in the encrypted payload and update the encrypted ICV without
being detected by the receiver.
With WPA, a method known as Michael specifies a new algorithm that calculates an 8-byte
message integrity code (MIC) using the calculation facilities available on existing wireless
devices. The MIC is placed between the data portion of the IEEE 802.11 frame and the 4-byte ICV.
The MIC field is encrypted together with the frame data and the ICV.
Michael also provides replay protection. A new frame counter in the IEEE 802.11 frame is used to
prevent replay attacks.
AES Support
One of the encryption methods supported by WPA beside TKIP is the advanced encryption
standard (AES), although AES support will not be required initially for Wi-Fi certification. This is
viewed as the optimal choice for security conscience organizations, but the problem with AES is
that it requires a fundamental redesign of the NIC’s hardware in both the station and the access
point. TKIP was a pragmatic compromise that allows organizations to deploy better security while
AES capable equipment is being designed, manufactured, and incrementally deployed.
User’s Manual for the Wireless Digital Media Player MP115
B-16 Wireless Networking Basics
November 2004 202-10038-01
Is WPA Perfect?
WPA is not without its vulnerabilities. Specifically, it is susceptible to denial of service (DoS)
attacks. If the access point receives two data packets that fail the Message Integrity Code (MIC)
check within 60 seconds of each other then the network is under an active attack, and as a result,
the access point employs counter measures, which includes disassociating each station using the
access point. This prevents an attacker from gleaning information about the encryption key and
alerts administrators, but it also causes users to lose network connectivity for 60 seconds. More
than anything else, this may just prove that no single security tactic is completely invulnerable.
WPA is a definite step forward in WLAN security over WEP and has to be thought of as a single
part of an end-to-end network security strategy.
Product Support for WPA
Starting in August, 2003, NETGEAR, Inc. wireless Wi-Fi certified products will support the WPA
standard. NETGEAR, Inc. wireless products that had their Wi-Fi certification approved before
August, 2003 will have one year to add WPA so as to maintain their Wi-Fi certification.
WPA requires software changes to the following:
Wireless access points
Wireless network adapters
Wireless client programs
Supporting a Mixture of WPA and WEP Wireless Clients
To support the gradual transition of WEP-based wireless networks to WPA, a wireless AP can
support both WEP and WPA clients at the same time. During the association, the wireless AP
determines which clients use WEP and which clients use WPA. The disadvantage to supporting a
mixture of WEP and WPA clients is that the global encryption key is not dynamic. This is because
WEP-based clients cannot support it. All other benefits to the WPA clients, such as integrity, are
maintained.
However, a mixed mode supporting WPA and non-WPA clients would offer network security that
is no better than that obtained with a non-WPA network, and thus this mode of operation is
discouraged.
Changes to Wireless Access Points
Wireless access points must have their firmware updated to support the following:
User’s Manual for the Wireless Digital Media Player MP115
Wireless Networking Basics B-17
November 2004 202-10038-01
The new WPA information element
To advertise their support of WPA, wireless APs send the beacon frame with a new 802.11
WPA information element that contains the wireless AP's security configuration (encryption
algorithms and wireless security configuration information).
The WPA two-phase authentication
Open system, then 802.1x (EAP with RADIUS or preshared key).
TKIP
Michael
AES (optional)
To upgrade your wireless access points to support WPA, obtain a WPA firmware update from your
wireless AP vendor and upload it to your wireless AP.
Changes to Wireless Network Adapters
Wireless network adapters must have their firmware updated to support the following:
The new WPA information element
Wireless clients must be able to process the WPA information element and respond with a
specific security configuration.
The WPA two-phase authentication
Open system, then 802.1x (EAP or preshared key).
TKIP
Michael
AES (optional)
To upgrade your wireless network adapters to support WPA, obtain a WPA update from your
wireless network adapter vendor and update the wireless network adapter driver.
For Windows wireless clients, you must obtain an updated network adapter driver that supports
WPA. For wireless network adapter drivers that are compatible with Windows XP (Service Pack 1)
and Windows Server 2003, the updated network adapter driver must be able to pass the adapter's
WPA capabilities and security configuration to the Wireless Zero Configuration service.
Microsoft has worked with many wireless vendors to embed the WPA firmware update in the
wireless adapter driver. So, to update you Windows wireless client, all you have to do is obtain the
new WPA-compatible driver and install the driver. The firmware is automatically updated when
the wireless network adapter driver is loaded in Windows.
User’s Manual for the Wireless Digital Media Player MP115
B-18 Wireless Networking Basics
November 2004 202-10038-01
Changes to Wireless Client Programs
Wireless client programs must be updated to permit the configuration of WPA authentication (and
preshared key) and the new WPA encryption algorithms (TKIP and the optional AES component).
To obtain the Microsoft WPA client program, visit the Microsoft Web site.
Index 1
November 2004 202-10038-01
Numerics
802.11b B-1
A
ad-hoc mode B-2
aspect ratio 5-4
Auto MDI/MDI-X G-2
Auto Uplink G-2
B
BSSID B-2
buttons, remote control 2-2
C
cables
Cat5 G-2
crossover G-2
television 3-2
Component Progressive and Component Interlaced,
setting 5-5
Component Video ports 2-3
Composite Video and L/R Audio ports 2-4
conventions, typography 1-1
customer support 1-ii
E
ESSID B-2
Ethernet link 6-2
Ethernet port 2-4
F
flash memory, for firmware upgrade 2-1
front panel 2-3
H
hidden networks 5-3
I
infrastructure mode B-2
installation 3-1, 3-2
selecting the network and server for the MP115 3-4
M
MDI/MDI-X G-2
MDI/MDI-X wiring G-4
media formats 4-1
Media Server Software
installation 3-2
overview 2-4
tabs 2-5, 4-2
MP115
installation 3-2
key features 2-1
requirements 3-1
N
networks
adding a new network for the MP115 5-2
configuration for hidden networks 5-3
hidden 5-3
Index
2 Index
November 2004 202-10038-01
O
Open System authentication B-4
P
package contents 2-5
ports
Component Video 2-3
Composite VIdeo and L/R Audio 2-4
Ethernet 2-4
SCART 2-4
S-Video 2-3
R
rear panel 2-3
remote control 2-2
searching alphabetically 4-4
Resource CD
Media Server software installation 3-2
Rhapsody Digital Music installation 3-2
Rhapsody Server, connecting to 6-4
S
SCART port 2-4
SCART setting 5-5
scope of document 1-1
searching alphabetically (remote control) 4-4
servers
connecting to 6-3
connecting to Rhapsody 6-4
Shared Key authentication B-4
SSID B-2
static IP Address, specifying 5-4
S-Video port 2-3
S-Video setting 5-5
T
television
cables 3-2
no display 6-1
V
video mode 5-5
video output
component 5-5
SCART 5-5
S-Video 5-5
video settings
aspect ratio 5-4
video mode 5-5
video output 5-5
Video Show 4-3
videos, watching 4-3
W
WEP B-8
Wi-Fi B-1, B-4
Wired Equivalent Privacy. See WEP
Wireless Ethernet B-1
wireless networks
configuration for hidden networks 5-3
location 5-4
World Wide Web 1-ii
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear MP115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear MP115 in the language / languages: English as an attachment in your email.

The manual is 4,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info