479751
12
Zoom out
Zoom in
Previous page
1/102
Next page
Table 1. Front panel LED descriptions
LED Description
Power/Test
Solid green. The startup is completed, and the router is ready.
Blinking green. The firmware is corrupted (see http://www.netgear.com/support).
Blinking amber. The firmware is upgrading, or the Reset button was pressed.
Off. Power is not supplied to the router.
Internet
Solid green. An IP address has been received; ready to transmit data.
Solid amber. An Ethernet cable connection to the modem has been detected.
Off. No Ethernet cable is connected to the modem.
LAN ports
1–4
Solid green. The local port is connected to a 1000 Mbps device.
Blinking green. Data is being transmitted at 1000 Mbps.
Solid amber. The local port is connected to a 10/100 Mbps device.
Blinking amber. Data is being transmitted at 10/100 Mbps.
Off. No link is detected on this port.
Wireless
Solid blue. The wireless interface is enabled.
Blinking blue. Data is being communicated over the wireless network.
Off. The wireless interface is turned off.
WPS
Solid green. A WPS-capable device has been accepted by the router and is ready to be used.
Blinking green. The WPS-capable device will be associated with the router within 2 minutes.
Off. No WPS connection exists.
Hardware Setup
12
N300 Wireless Gigabit Router JNR3000
The WLAN and WPS buttons toggle the WLAN and WPS functions on and off.
Wireless On/Off button. Pressing and holding the wireless LAN button for 2
seconds turns the 2.4 GHz wireless radio on and off. If the Wireless LED is lit, the
wireless radio is on. If the LED is off, then the wireless radio is turned off and you cannot
connect wirelessly to the router.
WPS button. You can use this button to use WPS to add a wireless device or
computer to your wireless network. The LED below the WPS button blinks green when
the router is trying to add the wireless device or computer. The LED stays solid green
when wireless security is enabled in the router.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear JNR3000 - N300 Wireless Gigabit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear JNR3000 - N300 Wireless Gigabit in the language / languages: English as an attachment in your email.

The manual is 7,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear JNR3000 - N300 Wireless Gigabit

Netgear JNR3000 - N300 Wireless Gigabit Installation Guide - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info