670497
68
Zoom out
Zoom in
Previous page
1/78
Next page
Troubleshooting
68
N150 and N300 Wireless Routers
All LEDs Remain Lit
When the router is turned on, the LEDs light for about 10 seconds and then turn off. If all the
LEDs stay lit, a fault exists within the router.
If all LEDs are still lit one minute after power-up, try the following:
Unplug the router’s
power adapter cord. Plug it in again and see if the router recovers.
T
o return the router to its factory settings, press and hold the Reset button.
For more information, see Factory Settings on page 76.
If the error persists, you might have a hardware problem. Contact technical support at
www.netgear.com/support.
Power LED Is Off or Blinking
If the Power LED is Off or blinking, try the following:
Make sure that the power adapter cord is securely connected to your router and securely
connected to a functioning power outlet.
Make sure that you are using the power adapter cord that NETGEAR supplied for this
product.
If the Power LED blinks slowly and continuously
, the router firmware is corrupted. This
situation can happen if a firmware upgrade is interrupted, or if the router detects a
problem with the firmware. If the error persists, you have a hardware problem. For
recovery instructions or help with a hardware problem, contact technical support at
www.netgear.com/support.
Power LED Stays Amber
When the router is turned on, the Power LED turns amber for about 20 seconds and
then turns green. If the LED does not turn green, the router has a problem.
If the Power LED is still amber one minute after you turn on power to the router, try the
following:
Unplug the router’s power adapter cord. Plug it in again and see if the router recovers.
T
o return the router to its factory settings, press and hold the Reset button.
For more information, see Factory Settings on page 76.
If the error persists, you might have a hardware problem. Contact technical support at
www.netgear.com/support.
Internet LEDs Is Off
If the Internet LED does not light, check the following:
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear JNR1010v2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear JNR1010v2 in the language / languages: English as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear JNR1010v2

Netgear JNR1010v2 Quick start guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info