710811
133
Zoom out
Zoom in
Previous page
1/480
Next page
8-Port or 16-Port Gigabit Smart Managed Pro Switch Model GS418TPP, GS510TLP, and GS510TPP
Configure Switching User Manual133
The range is 1500 to 9198. The default maximum frame size is 1500.
15. From the Flow Control menu, select the configuration for IEEE 802.3 flow control.
Disable. If the port buffers become full, the switch does not send pause frames, and
data loss could occur.
This is the default setting.
Symmetric. If the port buffers become full, the switch sends pause frames to stop
traffic.
Flow control helps to prevent data loss when the port cannot keep up with the number
of frames being switched. When you enable flow control, the switch can send a pause
frame to stop traf
fic on the port if the amount of memory used by the packets on the
port exceeds a preconfigured threshold and responds to pause requests from partner
devices. The paused port does not forward packets for the time that is specified in the
pause frame. When the pause frame time elapses, or the utilization returns to a
specified low threshold, the switch enables the port to again transmit frames. The
switch also honors incoming pause frames by temporarily halting transmission.
Asymmetric. If the port buf
fers become full, the switch does not send pause frames,
and data loss could occur. However
, the switch does honor incoming pause frames by
temporarily halting transmission.
Note: For LAG interfaces, flow control mode is displayed as a blank field
because flow control is not applicable.
16. Click the Apply button.
Your settings are saved.
The following table describes the nonconfigurable data that is displayed.
Table 30. Port Configuration information
Field Description
Port Type For normal ports this field is blank. Otherwise, the possible values are as
follows:
Physical Status The port speed and duplex mode.
Link Status Indicates whether the link is up or down.
MAC Address The physical address of the specified interface.
PortList Bit Offset The bit offset value that corresponds to the port when the MIB object type
PortList is used to manage in SNMP
.
ifIndex The ifIndex of the interface table entry associated with this port.
• Mirrored.
The port is a mirrored port on which all the traffic is copied
to the probe port.
• Probe
. Use this port to monitor a mirrored port.
• Trunk Member. The port is a member of a link aggregation trunk.
Look at the LAG pages for more information.
133


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear GS418TPP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear GS418TPP in the language / languages: English as an attachment in your email.

The manual is 7,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Netgear GS418TPP

Netgear GS418TPP Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info