710805

Netgear GC110 Manual

309
Zoom out
Zoom in
Previous page
1/416
Next page
Manage Device Security
309
Insight Managed 8-Port Gigabit Ethernet Smart Cloud Switch with 2 SFP Fiber Ports
• Interface. For a Permit action, use either a mirror interface or a redirect interface:
- Select the Mirror Interface radio button and use the menu to specify the egress
interface to which the matching traffic stream is copied, in addition to being
forwarded normally by the device.
- Select the Redirect Interface radio button and use the menu to specify the
egress interface to which the matching traffic stream is forced, bypassing any
forwarding decision normally performed by the device.
• Match Every. From the Match Every menu, select whether all packets must match
the selected IP ACL rule:
- False. Not all packets need to match the selected IP ACL rule. You can configure
other match criteria on the page.
- True. All packets must match the selected IP ACL rule and are either permitted or
denied. In this case, you cannot configure other match criteria on the page.
• Protocol Type. From the menu, select a protocol that a packet’s IP protocol must be
matched against: IP, ICMP, IGMP, TCP, UDP, EIGRP, GRE, IPINIP, OSPF, PIM, or
Other. If you select Other, specify enter a protocol number from 0 to 255.
• Src. In the Src field, enter a source IP address, using dotted-decimal notation, to be
compared to a packet’s source IP address as a match criterion for the selected IP
ACL rule:
- If you select the IP Address radio button, enter an IP address or an IP address
range. You can enter a relevant wildcard mask to apply this criteria. If this field is
left empty, it means any.
- If you select the Host radio button, the wildcard mask is configured as 0.0.0.0. If
this field is left empty, it means any.
The wildcard mask determines which bits are used and which bits are ignored. A
wildcard mask of 0.0.0.0 indicates that none of the bits are important. A wildcard of
255.255.255.255 indicates that all of the bits are important.
• Src L4. The options are available only when the protocol is set to TCP or UDP. Use the
source L4 port option to specify relevant matching conditions for L4 port numbers in
the extended ACL rule.
You can select either the Port radio button or the Range radio button:
- Port radio button. If you select the Port radio button, you can either enter the
port number yourself or select one of the following protocols from the menu:
• The source IP TCP port protocols are domain, echo, ftp, ftpdata, www-http,
smtp, telnet, pop2, pop3, and bgp.
• The source IP UDP port protocols are domain, echo, snmp, ntp, rip, time,
who, and tftp.
Each of these values translates into its equivalent port number, which is used as
both the start and end of the port range.
Select Other from the menu to enter a port number. If you select Other from the
menu but leave the field blank, it means any.
… 309 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear GC110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear GC110 in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info