571178
11
Zoom out
Zoom in
Previous page
1/48
Next page
11
3.3.5. Remote Control (optional)
This stove has the option of remote control.
Fitting the remote control motor:
At the rear of the appliance you will see the motor fitting bracket. This incorporates a magnet and the mechanism
friction plate. The friction plate is hinged. To fit the motor, this friction plate needs to be detached from the magnet
and swing to the left.
The motor can now be slipped into place. The magnet retains the motor.
Connect the electrical lead to the receiver box and place the receiver box in its holder.
Fig. 14 Fig. 15 Fig. 16
Detailed instructions on the use of the remote control can be found with the remote control kit.
3.4. LIGHTING
IMPORTANT! The surface of your device is protected
by a coat of special anti-heat paint that resists high
temperatures. When lighting the fireplace for the first
few times, the said paint may emit some fumes. This
is normal and is due to the evaporation of certain
components of the paint while it adapts to the heat.
We, therefore, recommend ventilating the room until
this phenomenon ceases to appear.
It is very important that the first time the heater is lit,
it is done so slowly. This is for the following reasons:
• Stabilise cast iron parts.
• Harden the joint sealant putty
We recommend that the first loads of fuel be small and
keep the stove on for a few hours at this intensity
The stove must be closed at all times during
combustion to prevent smoke from leaking out. Only
open to add fuel.
ATTENTION! During the operation of the stove, the
metal parts can reach hight temperatures. Protect
your hands with fire resistant gloves when touching
these parts.
Use the tool provided to operate the stove’s air
controls, as well as to open the ashpan door.
Fig. 17
Steps to light the stove:
1. Be sure the ash drawer is closed and secured. Slide
the Burn Type Lever to the centre position (See the
setting on fig.11).
2. Open the Burn Rate Knob all the way by turning to
the left. This knob may be turned manually or by
pressing “ON/HI” on the remote control (optional).
(See the setting on fig. 11). If your stove has the
Catalytic Hybrid Woodbox System, open the by-
pass placed in the top inside the stove (Fig. 18).
Draft control
(optional)
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nestor Martin S23 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nestor Martin S23 in the language / languages: English, Spanish as an attachment in your email.

The manual is 4.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nestor Martin S23

Nestor Martin S23 User Manual - Dutch, French - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info