653744

Nemox GELATO PRO 12K Manual

4
Zoom out
Zoom in
Previous page
1/23
Next page
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be observed, including the
following:
Read all instructions carefully.
To protect against risk of electric shock, do not put the main body of appliance in water or any other liquid.
Close supervision is necessary when any appliance is used by or near children.
Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
Avoid contact with moving parts.
Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions, or is dropped
or damaged in any manner. Return the appliance to an authorized Service Center for examination, repair or
electrical or mechanical adjustment.
The use of attachments not recommended or sold by the appliance manufacturer may result in fire, electric
shock or injury.
Do not use outdoors.
Do not let cord hang over edge of table or counter, or touch hot surfaces.
SAVE THESE INSTRUCTIONS
CAUTION
An authorized service representative should perform any servicing other than cleaning and user
maintenance. Authorized service personnel only should do repair.
Check that the voltage shown on the rating plate corresponds to the voltage of the mains.
Do not use sharp utensils inside the bowl! Sharp objects will scratch and damage the inside of the bowl. A
rubber spatula or metal spoon may be used, when the appliance is in the “OFF”or “0” position.
Never clean with scouring powders or hard implements.
Do not place or use the appliance on or near hot surfaces, such as stoves, hotplates, or near open gas
flames.
Do not put any part in the dishwasher.
Do not unplug the unit by pulling on the cord.
IMPORTANT:
This Ice Cream Machine contains its own refrigerant which must be allowed to settle after transport.
Leave the Ice Cream Machine on a horizontal surface for at least 12 hours after purchase or after any
move which might have stored the machine the wrong way up.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
After removing the appliance from the packaging, check it for damage. If in doubt, do not use the appliance
and contact an authorised service centre.
Plastic bags, polystyrene, nails, etc. must not be left within reach of children as they are potentially
dangerous.
The appliance's manufacturer and vendor reject any responsibility for failure to comply with the instructions
provided in this user manual.
The appliance must be connected to an electrical system and power supply socket with a minimum capacity
of 16A, equiped with an efficient earth contact. The manufacturer is not responsible for damages to things or
people in the event that the prescribed safety norms have not been respected.
Before carrying out any maintenance or cleaning operations, make sure that the appliance has been
disconnected from the electrical mains by removing the plug from the power supply socket.
Never wash the appliance using water jets or place it in water!
Leave at least 20 cm on each side of the machine to allow free air circulation. Make sure the vent slots are
free and unobstructed.
USING THE MACHINE FOR THE FIRST TIME PREPARATION OF THE MIXTURE.
Place your GELATO PRO 12K on a flat surface Select your recipe and follow it to prepare the
so that the ventilation slots (6) on either side are
mixture. Pay attention to the following:
unobstructed.
•Use pitted, peeled fruit and ingredients free of
Leave the appliance horizontal for at least 12
any waste matter.
hours before using it for the first time. If it has
•Always chill the ingredients in the refrigerator
been tilted in transit, the refrigerant must be
before pouring into the machine. This will
allowed to settle back into the correct position.
reduce the time required to prepare the ice
Hygiene is extremely important when making
cream.
ice cream. Before starting to use your ice cream
•Do not make up more than 2,5 Kg mixture.
machine, wash thoroughly all parts coming in
This will allow the mixture to increase during
contact with ice cream (bowl, paddle, lid, chute
churning to maximum bowl capacity.
and flat gate).
METHOD OF OPERATION
Mount the chute and fix it in position by the
•Check that voltage on the rating plate
appropriate screws (14).
corresponds to the voltage of the mains.
Mount the metal frame and fix it in position by
the appropriate screws (12). Place in position
•P
the tray and the cover grid.
Insert the flat gate in the appropriate seat and
•Insert the mixing paddle (5) in the container,
verify that there is no leaking when in closed
turning it clockwise until it is correctly
position.
positioned on the bottom.
Connect the plug to an electrical socket.
ower on the machine by rotating the general
power switch (10).
UK USERS ONLY
HOW TO CONNECT THE CORD TO A U.K. PLUG: IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Green and yellow: Earth
Blue: Neutral
Brown: Live
Please, read the instructions given below before connecting the cord to a plug. If
in doubt, please, consult a qualified electrician. As the colours of the wires in the
mains lead of this appliance may not correspond with the coloured markings
identifyng the terminals in your plug, proceed as follows: the wire that is coloured
Green and Yellow must be connected to the terminal in the plug which is marked
with the letter E or the Earth symbol (G), or coloured Green or Green and Yellow.
The wire that is coloured Brown must be connected to the terminal which is
marked with the letter L or coloured Red. The wire that is coloured Blue must be
connected to the terminal which is marked with the letter N or coloured Black.
SAFETY POINTS FOR REWIRABLE OR MOULDED PLUG
The mains lead of this appliance may be already fitted with a BS1363 13A plug.
If your socket outlet is not suitable for the plug, then the plug must be removed (cut off if it is a moulded on plug), the
flexible cord insulation should be stripped back as appropriate and a suitable 3 pin plug fitted.
WARNING: Dispose of a plug that has been cut from the power supply cord, as such a plug is hazardous if inserted in
a live 13A socket outlet elsewhere in the house.
Should the fuse need to be replaced an ASTA marked fuse, approved to BS 1362, of the same rating must be used.
Always replace the fuse cover after fitting a fuse. The plug must NOT be used if the cover is omitted or lost until a
replacement is obtained. Make certain that only the correct fuse cover is used and fitted.
For plugs with detachable fuse cover, the replacement must be the same as the colour insert in the base of the plug, or
as directed by the embossed wording on the base of the plug.
If the detachable fuse cover is lost a replacement may be purchased from a Service Centre.
Information for supply may also be obtained from the plug manufacturer.
•
•
•
•
•
•
•
•
•
•
English English
54
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nemox GELATO PRO 12K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nemox GELATO PRO 12K in the language / languages: English, German, Italian, Spanish as an attachment in your email.

The manual is 5,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info