727137
4
Zoom out
Zoom in
Previous page
1/56
Next page
4
English
Use
Setting the power
Press the function button until the power indicator
comes on. The display shows “1600”.
Turn the setting dial clockwise to increase the power.
Turn the setting dial counterclockwise to decrease the
power.
Setting the temperature
Press the function button until the temperature
indicator comes on. The display shows “200°”.
Turn the setting dial clockwise to increase the
temperature.
Turn the setting dial counterclockwise to decrease the
temperature.
Setting the timer
Press the function button until the timer indicator
comes on. The display shows “00:00”.
Turn the setting dial clockwise to set the hours.
Turn the setting dial counterclockwise to set the
minutes (1-minute steps).
Press the function button to conrm or wait until the
display stops ashing.
At the end of the countdown, a beep will sound and
the device will go to standby mode.
To cancel the function:
Press the on/o button to go to standby mode. The
timer indicator goes o.
Press and hold the function button to resume
operation with the set power or temperature settings.
The timer indicator goes o.
Hints for use
Insert the mains plug into the wall socket. A beep will
sound and the indicators ash once. The on/o
indicator starts to ash. The device is in standby mode.
Place the cookware in the centre of the cooking zone.
Press the on/o button to switch on the device. The
on/o indicator lights continuously. The display shows
“----”.
Set the device according to your cooking requirements.
After use, press the on/o button to set the device to
standby mode. The on/o indicator starts to ash.
Remove the mains plug from the wall socket.
Allow the device to cool down completely.
Error codes
Description Solution
E0
Internal circuit error.
(1) Use suitable cookware.
(2) Switch o the device, allow
the device to cool down
completely and switch the
device on again.
E1
No cookware or unsuitable
cookware used.
E7
Top plate overheating.
E2
Internal overheating.
Contact the service centre.
E3
Overvoltage.
E4
Undervoltage.
E5
Open-circuit error or
short-circuit error
(top plate sensor).
E6
Open-circuit error or
short-circuit error
(IGBT sensor).
Cleaning and maintenance
Warning!
Before cleaning or maintenance, switch o the device,
remove the mains plug from the wall socket and wait
until the device has cooled down.
Do not use cleaning solvents or abrasives.
Do not immerse the device in water or other liquids.
Do not attempt to repair the device. If the device does
not operate correctly, replace it with a new device.
Clean the outside of the device using a soft, damp
cloth. If necessary, use a little neutral detergent.
Thoroughly dry the outside of the device with a clean,
dry cloth.
Clean the ventilation openings using a soft brush.
Technical data
Power settings
300 W / 600 W / 900 W / 1200 W /
1400 W / 1600 W / 1800 W / 2000 W
Temperature settings
60 °C / 80 °C / 100 °C / 120 °C
140 °C / 160 °C / 180 °C / 200 °C
Timer settings 1 minute ~ 11 hours / 59 minutes
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nedis KAIP120CWT1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nedis KAIP120CWT1 in the language / languages: All languages as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info