812860
5
Zoom out
Zoom in
Previous page
1/40
Next page
5
Spraying a burst of steam
1. Set the thermostat dial Ar to the second or third position.
2. Set the steam selector A4 to the maximum position.
3. Press the burst button A2 to spray a burst of steam.
4Wait at least 5 seconds between bursts of steam.
4Do not use the steam burst button for more than 5 consecutive
seconds.
4Hold the product vertical and use bursts of steam to remove
creases from hanging fabric.
Spraying a spray of steam
Press the spray button A3 to spray steam.
After use
1. Set the thermostat dial Ar to the minimum position.
2. Place the product on the back cover Aw.
3. Unplug the power cable A1 from the power outlet.
Troubleshooting
Problem Possible cause Possible solution
The product doesn’t
produce heat.
The thermostat
dial Ar is rotated
to OFF.
Set the thermostat
dial Ar to the
correct setting for
your fabric.
The product is not
plugged in.
Plug the power
cable A1 into a
power outlet.
The burst of steam
doesn’t function.
The burst of steam
function has been
used to often.
Continue ironing in
horizontal position
and wait a while
before using the
burst of steam
function again.
The water reservoir
A6 is empty.
Fill the water
reservoir A6 with
distilled water.
The ironing plate
A8 leaks water.
The thermostat dial
Ar is out of the
steam range.
Set the thermostat
dial Ar to the third
position.
The product has not
fully heated up yet.
Wait until the LED
indicator Ae
switches o to
indicate the product
is heated up.
The amount of
water exceeds the
MAX indicator of
the water reservoir
A6.
Pour out the excess
water from the
water reservoir A6.
The product doesn’t
produce enough
steam.
Set the steam
selector A4 to 0.
Set the steam
selector A4 to
the desired steam
output.
The steam holes
A9 are blocked.
Clean the steam
holes A9 with
distilled water.
The water reservoir
A6 is empty.
Fill the water
reservoir A6 with
distilled water.
The spray nozzle
A7 doesn’t spray.
There is not enough
pressure or air inside
of the product.
1. Push the spray
nozzle A7 by
hand.
2. Push the spray
button A3
multiple times.
Cleaning the product
-
Disconnect the product before cleaning.
-
Before cleaning and maintenance, switch o the product and
disconnect the power. Let the product cool down completely.
-
Do not use aggressive chemical cleaning agents such as
ammonia, acid or acetone when cleaning the product.
-
Do not clean the inside of the product.
-
Disconnect the product from the power source before service
and when replacing parts.
1. Clean the product regularly with a soft, clean, dry cloth. Avoid
abrasives that can damage the surface.
2. Clean the ironing plate A8 with a damp cloth and a non-
abrasive cleaner.
3. Clean the ironing plate A8 with a damp cloth with vinegar if
ber is stuck to the ironing plate A8.
4. Remove any limescale from the steam holes A9 with a
toothpick.
5. Empty the water reservoir A6.
4To remove all water from the water reservoir A6 and product,
connect the product to a power outlet and set the thermostat
dial Ar to the maximum position for two minutes.
4The built-in anti-scale cartridge reduces the build-up of limescale.
The built-in anti-scale cartridge does not stop the natural process
of limescale build-up.
Self-cleaning function
Use the self-cleaning function once every two weeks.
4Use distilled water.
1. Fill the measuring cup Ay with water.
2. Open the water reservoir cover A5.
3. Empty the measuring cup Ay into the water reservoir A6.
4. Close the water reservoir cover A5.
5. Place the product on the back cover Aw.
6. Plug the power cable A1 into a power outlet.
7. Set the thermostat dial Ar to the maximum position.
Wait until the LED indicator Ae switches o to indicate the product
is heated up.
8. Unplug the power cable A1 from the power outlet.
9. Hold the product horizontally above the sink.
10. Press and hold the self-cleaning button At until the water
reservoir A6 is empty.
Boiling water and steam ejects to remove the impurities from the
steam holes A9.
11. Plug the power cable A1 into a power outlet.
12. Iron an old piece of cloth to dry the ironing plate A8.
13. Unplug the power cable A1 from the power outlet.
Disposal The product is designated for separate collection at
an appropriate collection point. Do not dispose of the
product with household waste.
For more information, contact the retailer or the local
authority responsible for the waste management.
c Kurzanleitung
Dampfbügeleisen IRON2000
Weitere Informationen nden Sie in der erweiterten
Anleitung online: ned.is/iron2000
Bestimmungsgemäße Verwendung
Dieses Produkt ist ein Dampfbügeleisen, das für eine breite Auswahl
von Stoen verwendet werden kann.
Dieses Produkt ist mit einem Tropfschutzsystem ausgestattet, das
verhindert, dass Wasser aus der Bügelsohle austritt, wenn das
Produkt kalt ist.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nedis IRON2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nedis IRON2000 in the language / languages: All languages as an attachment in your email.

The manual is 2.83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info