214406
146
Zoom out
Zoom in
Previous page
1/157
Next page
139
8. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 138.)
Does not turn on
Will turn off
No picture
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 29 and 31.
Ensure that the lamp cover is installed correctly. See page 136.
Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 4100 hours : Eco
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-
ticularly warm, move the projector to a cooler location.
If you turn on the projector immediately after the lamp is turned off or when the temperature is high, the fans
run without displaying an image for some time and then the projector will display the image. Wait for a
moment.
The lamp may fail to light. Wait a full minute and then turn on the power again.
The lamp has reached the end of its usable life. Replace the lamp. See page 134.
After replacing the lamp, press and hold the HELP button on the remote control for a minimum of 10 seconds
to clear the lamp usage time. This will allow you to turn on the projector.
Ensure that the Power Management is off. See page 120.
Use the SOURCE button on the projector cabinet or the COMPUTER, VIDEO or VIEWER button on the remote
control to select your source. See page 40.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page 88.
Open the mirror cover. See page 6.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. See page 129.
Enter your registered keyword if the Security function is enabled. See page 60.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER
button again to resume.
See also the next page.
Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 89.
Adjust "Hue" in "Adjust". See page 89.
Reposition the projector to improve its angle to the screen. See page 33.
Use the 3DReform function to correct the trapezoid distortion. See page 99.
Adjust the focus. See page 35.
Reposition the projector to improve its angle to the screen. See page 33.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
16.
Condensation may form on the mirror if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the mirror.
Use the SOURCE button on the projector cabinet or the COMPUTER, VIDEO or VIEWER button on the remote
control to select your source (Video, S-Video, Computer, Viewer or LAN). See page 40.
Adjust the computer image manually with the “Clock”/“Phase” in “Adjust” “Image Options”. See page 95.
Install new batteries. See page 12.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page 12.
See the POWER/STATUS/LAMP Indicator on page 138.
Problem Check These Items
146


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec wt 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec wt 610 in the language / languages: English as an attachment in your email.

The manual is 5,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info