214297
59
Zoom out
Zoom in
Previous page
1/71
Next page
7-1
This section describes the simple maintenance procedures you
should follow to replace the lamp, and to clean the cabinet and
the mirror.
7-1. Replacing the Lamp
After your lamp has been operating for 2000 hours (up to 3000
hours : Eco mode) or longer, the "Lamp" indicator in the cabinet
will blink red and the message will appear. Even though the lamp
may still be working, replace it at 2000 hours (up to 3000 hours
: Eco mode) to maintain optimal projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait
90 seconds, turn off the main power switch, and then dis-
connect the power cable. Allow at least one hour for the
lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except the lamp cover
screw and two lamp case screws. You could receive an
electric shock.
The projector will turn off and go into stand by mode af-
ter 2100 hours (up to 3100 hours : Eco mode) of service.
If this happens, be sure to replace the lamp. If you con-
tinue to use the lamp after 2000 hours (up to 3000 hours :
Eco mode) of use, the lamp bulb may shatter, and pieces
of glass may be scattered in the lamp housing. Do not
touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replace-
ment.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp
cover screw is not removable.
2. Loosen the two screws securing the lamp housing until the
screwdriver goes into a freewheeling condition. The two screws
are not removable.
3. Remove the lamp housing by pulling out the handle.
Interlock
7. Maintenance
5. Secure it in place with the two screws.
Be sure to tighten the screws.
6. Reattach the lamp cover.
7. Tighten the lamp cover screw.
Be sure to tighten the screw.
8. After you install a new lamp, from the menu select [Projector
Options]
[Setup]
[Page 4]
[Clear Lamp Hour Meter] to
reset the lamp usage hours.
If the projector will not be turned on after using 2100 hours
(up to 3100 hours : Eco mode) of service, press and hold the
[Help] button on the remote control for ten seconds or longer
to reset the lamp time clock to zero.
NOTE: There is an interlock on this case to prevent the risk of electri-
cal shock. Do not attempt to circumvent this interlock.
4. Insert a new lamp housing until the lamp housing is plugged
into the socket.
CAUTION: Do not use a lamp other than the NEC replace-
ment lamp (LT60LPK).
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec wt 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec wt 600 in the language / languages: English as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info