215367
33
Zoom out
Zoom in
Previous page
1/150
Next page
21
3. Projecting an Image (Basic Operation)
ENTER
MAGNIFYVOLUME
PICTURE
LAMP MODE
ASPECT
AV-MUTE
3D REFORM
FREEZE
ID SET
LENS SHIFT
FOCUS
/ZOOM
HELP
PAGE
MENU
L-CLICK
R-CLICK
EXIT
0
CLEAR
UP
DOWN
ID
ID
MAGNIFYVOLUME
PICTURE
LAMP MODE
ASPECT
AV-MUTE
3D REFORM
FREEZE
ID SET
LENS SHIFT
FOCUS
/ZOOM
HELP
PAGE
MENU
L-CLICK
R-CLICK
EXIT
ENTER
UP
DOWN
ID
SO
AUTO ADJUST
3D REFORM
SELECT
SO
AUTO ADJUST
3D REFORM
SELECT
Note on Startup screen (Menu Language Select screen)
When you  rst turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select
one of the 21 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT button to select one of the 21 lan-
guages for the menu.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu
operation.
If you want, you can select the menu language later. (
[LANGUAGE] on page
91)
NOTE:
The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking
green.
If you turn on the projector immediately after the lamp is turned off or when the ambient temperature is high, the cooling fans
will run for a moment and then you will get an image on the screen.
Immediately after turning on the projector, screen fl icker may occur. This is normal. Wait 3 to 5 minutes until the lamp light-
ing is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
- If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In
this condition the projector will not turn on to protect the internal system. If this happens, wait for the projec-
tor’s internal components to cool down.
- When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
( page
117)
- If the lamp fails to light, and if the STATUS indicator  ashes on and off in a cycle of six times, wait a full min-
ute and then turn on the power.
NOTE: Turning the Main Power Switch Off then Back On
Allow a minimum of 5 seconds between turning off the main power switch and turning it back on again.
The same will be applied when a power strip equipped with a switch and a breaker is used.
Failing to do so could result in no power to the projector. (There will be no stand-by LED)
Should this happen, unplug the power cable and plug it in again. Turn on the main power switch.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec vt800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec vt800 in the language / languages: English as an attachment in your email.

The manual is 13,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info