214294
114
Zoom out
Zoom in
Previous page
1/126
Next page
114
9. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 113.)
Does not turn on
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or
blinking
Cross color in RGB
mode
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 28 and 30.
Ensure that the lamp cover is installed correctly. See page 110.
Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 3100 hours : Eco
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-
ticularly warm, move the projector to a cooler location.
The lamp may fail to light. Wait a full minute and then turn on the power again.
The lamp has reached the end of its usable life. Replace the lamp.
Ensure that the Power Management is off. See page 96.
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPONENT, the COM-
PUTER 1/2 or the VIEWER button on the remote control to select your source (Computer 1/2, Component,
Video, S-Video or Viewer). See page 32.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page 78.
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. See page 103.
Enter your registered keyword if the Security function is enabled. See page 49.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 60 seconds and then press the POWER
button again to resume.
See also the next page.
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen) To return to the Normal mode, select another available
source.
* When the image is muted using the PIC-MUTE button on the remote control Press the PIC-MUTE button
again to return to the Normal mode.
* When the room where you' re presenting is particularly warm Move the projector to a cooler location.
Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 80.
Adjust "Hue" in "Picture". See page 78.
Reposition the projector to improve its angle to the screen. See page 33.
Use the 3DReform function to correct the trapezoid distortion. See page 35.
Adjust the focus. See page 34.
Reposition the projector to improve its angle to the screen. See page 33.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
22.
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPONENT, the COM-
PUTER 1/2 or the VIEWER button on the remote control to select your source (Video, S-Video, Component,
Computer or Viewer). See page 32.
Adjust the computer image manually with the Pixel Adjust/Position in the Image. See page 84.
Install new batteries. See page 19.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page 19.
Check if one or more remote sensors are enabled. Select [Setup] [Page 4] [Remote Sensor] from the
menu. See page 98.
Make sure that you are in the Projector mode and the PJ button lights in red. If not, press the PJ button. See
page 40.
See the POWER/STATUS/LAMP Indicator on page 113.
Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. See
page 37.
Adjust the computer image manually with the Pixel Adjust/Position in the Image. See page 84.
Problem Check These Items
For more information contact your dealer.
114


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec vt 770 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec vt 770 in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info