214756
60
Zoom out
Zoom in
Previous page
1/79
Next page
52
» Replacing the Lamp
After your lamp has been operating for 2000
*1
hours (up to 3000
*1
hours in Eco mode) or longer, the LAMP indicator in
the cabinet will blink red and the message [The lamp has reached the end of its usable life. Please replace the
lamp.]
*2
will appear. Even though the lamp may still be working, replace it at 2000
*1
(up to 3000
*1
hours in Eco mode)
hours to maintain optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter.
( page 49)
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour
for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except two lamp case screws. You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might
cause an unwanted shadow and poor picture quality.
The projector will turn off and go into standby mode after 2100
*1
(up to 3100
*1
hours in Eco mode) hours of service.
If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000
*1
hours (up to 3000
*1
hours
in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not
touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for lamp
replacement.
*
1
NOTE: Lamp life for VT59/VT49 is 3000 hours in Normal mode and 4000 hours in Eco mode.
The projector will turn off and go into standby mode after 3100 (up to 4100 hours in Eco mode) hours of service.
*
2
NOTE: This message will be displayed under the following conditions:
for one minute after the projector has been powered on
when the POWER ON/STAND BY button on the projector cabinet or the POWER OFF button on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
To replace the lamp:
Optional lamp and tools needed for replacement:
Replacement lamp VT85LP (VT695/VT595/VT590/VT491) or VT80LP (VT59/VT49)
1. Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.
6. Maintenance
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec vt 595 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec vt 595 in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec vt 595

Nec vt 595 User Manual - Dutch - 79 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info