493538

Nec VT 465 Manual

29
Zoom out
Zoom in
Previous page
1/42
Next page
E-29
Default
Returning to Factory Default [Factory Default]
The Factory Default feature allows you to change adjustments and set-
ting to the factory preset for source except the following:
<Current Signal>
Resets the adjustments for the current signal to the factory preset lev-
els.
The items that can be reset are: Brightness, Contrast, Color, Hue, Sharp-
ness, Aspect Ratio, Horizontal Position, Vertical Position, Clock, Phase
and Picture Management.
<All Data>
Reset all the adjustments and settings for all the signals to the factory
preset.
The items can be reset except Language, Security, Communication
Speed, Remaining Lamp Time, Lamp Hour Meter, Filter Usage and Pro-
jector Usage. To reset the lamp usage time, see “Clear Lamp Hour Meter”
and “Clear Filter Usage”.
Resetting the Filter Usage Hours [Clear Filter Usage]
Resets the filter usage back to zero. Selecting this option displays
submenu for a confirmation.
Clearing Lamp Hour Meter [Clear Lamp Hour Meter]
Resets the lamp clock back to zero. Selecting this option displays
submenu for a confirmation.
NOTE: The projector will turn off and go into standby mode after 2100 hours (up
to 3100 hours in Eco mode) of service. If this happens, press the “Help” button
on the remote control for ten seconds to reset the lamp clock back to zero. Do
this only after replacing the lamp.
Enabling Auto Adjust [Auto Adjust]
When “Auto Adjust” is set to “On”, the projector automatically deter-
mines the best resolution for the current RGB input signal to project
an image using NEC’s Advanced AccuBlend Intelligent Pixel Blend-
ing Technology.
The image can be automatically adjusted for position and stability;
“Horizontal Position”, “Vertical Position”, “Clock” and “Phase”.
On .................. Automatically adjusts image “Horizontal Position”,
“Vertical Position”, “Clock” and “Phase”.
Off .................. User can adjust the image display functions (“Hori-
zontal Position”, “Vertical Position”, “Clock” and
“Phase”) manually.
Adjusting Position/Clock (when Auto Adjust is off)
This allows you to manually adjust the image horizontally and verti-
cally, and adjust Clock and Phase.
<Horizontal/Vertical>
Adjusts the image location horizontally and vertically.
This adjustment is made automatically when the Auto Adjust is turned
on.
<Clock>
Use this item with the “Auto Adjust off” to fine tune the computer
image or to remove any vertical banding that might appear. This func-
tion adjusts the clock frequencies that eliminate the horizontal band-
ing in the image. This adjustment may be necessary when you con-
nect your computer for the first time. This adjustment is made auto-
matically when the Auto Adjust is turned on.
<Phase>
Use this item to adjust the clock phase or to reduce video noise, dot
interference or cross talk. (This is evident when part of your image
appears to be shimmering.)
Use “Phase” only after the “Clock” is complete.
This adjustment is made automatically when the Auto Adjust is turned
on.
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (DIN 8 Pin). It
supports data rates from 4800 to 19200 bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected
(depending on the equipment, a lower baud rate may be recom-
mended for long cable runs).
Information
Displays the status of the current signal and lamp usage. This item has
three pages. The information included is as follows:
[Page 1]
Source Index
Horizontal Frequency
Vertical Frequency
Sync Polarity
[Page 2]
Signal Type
Video Type
Sync Type
Interlace
[Page 3]
Remaining Lamp Time (%)*
Lamp Hour Meter (H)
Filter Usage
Projector Usage
* The progress indicator shows the
percentage of remaining bulb life.
The value informs you of the
amount of lamp usage. When the
remaining lamp time reaches 0,
the Remaining Lamp Time bar in-
dicator changes from 0% to 100
Hours and starts counting down.
If the remaining lamp time reaches
0 hours, the projector will not turn
on regardless of whether the lamp
mode is set to Normal or Eco.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec VT 465 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec VT 465 in the language / languages: English as an attachment in your email.

The manual is 2,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info