215366
143
Zoom out
Zoom in
Previous page
1/166
Next page
129
8. Appendix
Common Problems & Solutions
(
“Power/Status/Lamp Indicator” on page 128)
Problem Check These Items
Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control
is on. (
page 21, 22)
Ensure that the lamp cover is installed correctly. (
page 127)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 600 hours after the lamp has reached the end of its
life. If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
page 121)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600 meters
or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple
minutes and turn on the projector. (
page 115)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the
projector has cooled down, the fan will run a short time before the lamp will turn on.
Will turn off Ensure that the [OFF TIMER], [PROGRAM TIMER] or [AUTO POWER OFF] is off. (
page 90, 115)
No picture Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COMPUTER 2,
the HDMI, the VIEWER or the NETWORK button on the remote control to select your source. (
page 24)
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. (
page 80)
Check to see if the image is muted. (
page 33)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. (
page 121)
Enter your registered keyword if the Security function is enabled. (
page 43)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the
power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver or
power management software.
See also the next page.
Color tone or hue is
unusual
Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (
page 89)
Adjust [HUE] in [ADJUST]. (
page 80)
Image isn’t square to the
screen
Reposition the projector to improve its angle to the screen. (
page 25)
Use the 3DReform function to correct the trapezoid distortion. (
page 28)
Picture is blurred Adjust the focus. (
page 26)
Reposition the projector to improve its angle to the screen. (
page 25)
Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
page
136)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on screen Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500
feet/1600 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and set-
ting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
(
page 115)
Image is scrolling verti-
cally, horizontally or both
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COMPUTER 2,
the HDMI, the VIEWER or the NETWORK button on the remote control to select your source (Video, S-Video, Com-
puter, Component, Viewer or NETWORK). (
page 24)
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
[IMAGE OPTIONS]. (
page 81)
Remote control does not
work
Install new batteries. (
page 9)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. (
page 9)
Check if one or more remote sensors are enabled. Select [SETUP]
[INSTALLATION (2)]
[REMOTE SENSOR]
from the menu. (
page 113)
Make sure that the remote control’s ID corresponds with the projector’s ID.
Indicator is lit or blinking See the POWER/STATUS/LAMP Indicator. (
page 128)
Vertical stripes in RGB
mode
Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. (
page
30)
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
[IMAGE OPTIONS]. (
page 81)
USB mouse does not
work
Make sure that your USB mouse is properly connected to the projector. (
page 35)
The projector may not support some brands of a USB mouse.
Some menu items cannot be operated with a USB mouse.
Moving images are not
correctly played in the
Viewer
Depending on your wireless LAN environment, moving images may not correctly played in the Viewer. If such a
case frequently occurs, remove the Wireless LAN Unit from the projector. (
page 143)
For more information contact your dealer.
143


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np905 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np905 in the language / languages: English as an attachment in your email.

The manual is 13,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np905

Nec np905 User Manual - German - 166 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info