654080
92
Zoom out
Zoom in
Previous page
1/107
Next page
83
8. Appendix
Troubleshooting
Thissectionhelpsyouresolveproblemsyoumayencounterwhilesettinguporusingtheprojector.
Indicator Messages
Power Indicator
Indicator Condition Projector Condition Note
Off The main power is off
Blinkinglight
Green
0.5secOn,
0.5secOff
The projector is getting ready to turn on� Wait for a moment�
2.5secOn,
0.5secOff
OffTimerisenabled.
Orange
0.5secOn,
0.5secOff
The projector is cooling down Wait for a moment�
Steady light
Green
The projector is turned on
Orange
[NO RM AL] is se le cte d fo r [S TA NDBY
MODE]
Status Indicator
Indicator Condition Projector Condition Note
Off
NormalorStandby([POWER-SAVING]for
[STANDBYMODE])
Blinkinglight
Red
1cycle(0.5secOn,2.5
secOff)
Lampcovererrororlamphousingerror Replace the lamp cover or lamp housing correctly�
2cycle(0.5secOn,0.5
secOff)
Temperature error
The projector is overheated Move the projector to a
cooler location�
3cycle(0.5secOn,0.5
secOff)
Power error
Power unit is not working properly.Contac tyour
dealer
4cycle(0.5secOn,0.5
secOff)
Fanerror Fanswillnotworkcorrectly.
6cycle(0.5secOn,0.5
secOff)
Lamperror
Lampfailstolight.Waitafullminuteandthenturnon
again�
8 cycle in red and 1
cycle in green (0�5 sec
On,0.5secOff)or
8 cycle in red and 2
cycle in green (0�5 sec
On,0.5secOff)
Cooling pump error
• The two screws on the lamp housing are notcom-
pletely tightened� Tighten the two screws alternately
until both screws are completely tightened�
• Thecooling pump is not working properly. Contact
your dealer�
Green
Re-firing the lamp (The projector is cooling
down�)
The projector is re-firing�
Wait for a moment�
Steady light
Green
Standby([NORMAL]for[STANDBYMODE])
Orange
CONTROLPANELLOCKison.
You have pressed cabinet button when Control Panel
Lockison.
CONTROLIDerror Remote control ID and projector ID are not matched�
Lamp Indicator
Indicator Condition Projector Condition Note
Off Normal
Blinkinglight Red
Lamp has reachedits endof life. Lamp re-
placement message will be displayed�
Replace the lamp�
Steady light
Red
Lamp hasbeen usedbeyond itslimit. The
projector will not turn on until the lamp is
replaced�
Replace the lamp�
Green [ECOMODE]issetto[ON]
Over-Temperature Protection
Ifthetemperatureinsidetheprojectorrisestoohigh,theover-temperatureprotectorwillautomaticallyturnoffthe
lampwiththeSTATUSindicatorblinking(2-cycleOnandOff.)
Shouldthishappen,dothefollowing:
-Unplugthepowercableafterthecoolingfansstop.
-Movetheprojectortoacoolerlocationiftheroomwhereyouarepresentingisparticularlytoowarm.
-Cleantheventilationholesiftheyarecloggedwithdust.
-Waitabout60minutesuntiltheinsideoftheprojectorbecomescoolenough.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec NP64 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec NP64 in the language / languages: English as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info