Manual Nec NP54 (page 93 of 107) (English)

654078

Zoom out

Zoom in

1/107

8. Appendix

Common Problems & Solutions (→“Power/Status/LampIndicator”onpage83.)

Problem Check These Items

Does not turn on

• Checkthatthepowercableispluggedinandthatthepowerbuttonontheprojectorcabinetortheremotecontrolis

on� (→ page 15, 16)

• Ensurethatthelampcoverisinstalledcorrectly.(→ page 81)

• Ensurethatthetwoscrewsonthelamphousingarecompletelytightened.(→ page 81)

• Ensurethatthecoolingpumpisinstalledcorrectly.(→ page 82)

• Checktoseeiftheprojectorhasoverheated.Ifthereisinsufcientventilationaroundtheprojectororiftheroom

where you are presenting is particularly warm, move the projector to a cooler location�

• Checktoseeifyoucontinuetousetheprojectorforanother100hoursafterthelamphasreachedtheendofitslife.

If so, replace the lamp�

 Afterreplacingthelamp,resetthelamphoursused.(→ page 77)

• Thelampmayfailtolight.Waitafullminuteandthenturnonthepoweragain.

• Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5000feet/1500meters

orhigher.Usingtheprojectorataltitudesapproximately5000feet/1500metersorhigherwithoutsettingto[HIGH

ALTITUDE]cancausetheprojectortooverheatandtheprojectorcouldshutdown.Ifthishappens,waitacouple

minutes and turn on the projector� (→ page 71)

 Alsowhenthelampisturnedoff,theprojectorinternaltemperatureishot.Ifthepoweristurnedonbeforethepro-

jector has cooled down, the fan will run a short time before the lamp will turn on�

Will turn off • Ensurethatthe[OFFTIMER]or[AUTOPOWEROFF]isoff.(→ page 72, 73)

• Checkiftheprojectorhasstayedwithitslenscoverclosedformorethan2hours.(→ page 5)

No picture

• Usetheappropriatesourcebuttonontheremotecontroltoselectyoursource.(→ page 18) If there is still no pic-

ture, press the button again�

• Ensureyourcablesareconnectedproperly.

• Usemenustoadjustthecontrastandbrightness.(→ page 59)

• Checktoseeiftheimageismuted.(→ page 30)

• Ensurethatthelenscoverisopen.(→ page 5)

• Resetthesettingsoradjustmentstofactorypresetlevelsusingthe[RESET]intheMenu.(→ page 77)

• EnteryourregisteredkeywordiftheSECURITYfunctionisenabled.(→ page 33)

• BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturningonthe

powertothenotebookPC.

 InmostcasestheoutputsignalfromthenotebookPCisnotturnedonunlessconnectedtotheprojectorbeforebe-

ing powered up�

* Ifthescreengoesblankwhileusingyourremotecontrol,itmaybetheresultofthecomputer’sscreen-saveror

power management software�

• Seealsothenextpage.

Picture suddenly be-

comesdark

• Whenoneofthefollowinghappens,the[ECOMODE]automaticallychangesfrom[OFF]to[ON].

* Whentherearenosignals(blueorblackscreen)→Toreturntothe[OFF]mode,selectanotheravailablesource.

* Whentheroomwhereyou’representingisparticularlywarm→ Move the projector to a cooler location�

Imageisn’tsquaretothe

screen

• Repositiontheprojectortoimproveitsangletothescreen.(→ page 20, 21)

• UsetheKEYSTONEcorrectionfunctiontocorrectthetrapezoiddistortion.(→ page 25)

Picture is blurred

• Makesurethatfocusisappropriate.

• Repositiontheprojectortoimproveitsangletothescreen.(→ page 20, 21)

• Ensurethatthedistancebetweentheprojectorandscreeniswithintheadjustmentrangeofthelens.(→ page 10)

• MakesurethatthedistancebetweenthefocussensorandthescreeniswithintheeffectiverangeoftheAUTOFO-

CUS� (→ page 22)

• MakesurethattherequirementsfortheAUTOFOCUSaremet.(→ page 22)

• Condensationmayformonthelensiftheprojectoriscold,broughtintoawarmplaceandisthenturnedon.Should

this happen, let the projector stand until there is no condensation on the lens�

Flicker appears on screen • Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5000

feet/1500 meters or lower. Using the projector at altitudes less than approximately 5000 feet/1500 meters and setting

to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to icker. Switch [FAN MODE] to [AUTO].

(

→

page 71)

Image is scrolling verti-

cally, horizontally or both

• Usetheappropriatesourcebuttonontheremotecontroltoselectyoursource.(→ page 18)

• Adjustthecomputerimagemanuallywiththe[HORIZONTAL]and[VERTICAL]in[ADJUST]→[IMAGEOPTIONS]in

the menu� (→ page 61)

Remote control does not

work

• Installnewbatteries.(→ page 8)

• Makesuretherearenoobstaclesbetweenyouandtheprojector.

• Standwithin22feet(7m)oftheprojector.(→ page 8)

Indicatorislitorblinking • SeethePOWER/STATUS/LAMPIndicator.(→ page 83)

CrosscolorinRGBmode • PresstheAUTOADJ.buttonontheremotecontrol(◀ button on the projector cabinet)� (→ page 27)

• Adjustthecomputerimagemanuallywith[CLOCK]and[PHASE]in[ADJUST]→[IMAGEOPTIONS]inthemenu.(→

page 60)

Cannot control the pro-

jector in standby mode

from the PC Control�

• Checkif[STANDBYMODE]isnotsetto[POWER-SAVING].

The projector does not

operate correctly�

• Turnoffthepowerandunplug thepowercable.Waitfor5minutes.Plugthepowercableandturnonthepower

again�

Formoreinformationcontactyourdealer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nec NP54 in the language / languages: English as an attachment in your email.

The manual is 5,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec NP54

Nec NP54 User Manual - German - 107 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nec NP54 Manual

Product: