215754
86
Zoom out
Zoom in
Previous page
1/100
Next page
77
8. Appendx
Common Problems & Solutons ("Power/Status/LampIndicator"onpage76.)
Problem Check These Items
Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control
is on. ( page 15, 16)
Ensure that the lamp cover is installed correctly. (
page 74)
Ensure that the two screws on the lamp housing are completely tightened.(
page 74)
Ensure that the cooling pump is installed correctly. (
page 75)
Check to see if the projector has overheated. If there is insufcient ventilation around the projector or if the room
where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its
life. If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
page 70)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5000 feet/1500 meters
or higher. Using the projector at altitudes approximately 5000 feet/1500 meters or higher without setting to [HIGH
ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens, wait a couple
minutes and turn on the projector. ( page 65)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the
projector has cooled down, the fan will run a short time before the lamp will turn on.
Will turn off Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. ( page 66, 67)
No picture Use the appropriate source button on the remote control to select your source. ( page 18) If there is still no pic-
ture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the contrast and brightness. (
page 55)
Check to see if the image is muted. (
page 29)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (
page 70)
Enter your registered keyword if the SECURITY function is enabled. (
page 30)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the
power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or
power management software.
See also the next page.
Picture suddenly becomes
dark
When one of the following happens, the [LAMP MODE] automatically changes from [NORMAL] to [ECO].
* When there are no signals (blue or black screen) To return to the NORMAL mode, select another available
source.
* When the room where you' re presenting is particularly warm
Move the projector to a cooler location.
Color tone or hue is unusu-
al
Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (
page 61)
Adjust [HUE] in [ADJUST]
[BASIC]. ( page 55)
Image isn’t square to the
screen
Reposition the projector to improve its angle to the screen. (
page 20, 21)
Use the KEYSTONE correction function to correct the trapezoid distortion. (
page 25)
Picture is blurred Make sure that focus is appropriate.
Reposition the projector to improve its angle to the screen. (
page 20, 21)
Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
page 10)
Make sure that the distance between the focus sensor and the screen is within the effective range of the AUTO
FOCUS. ( page 22)
Make sure that the requirements for the AUTO FOCUS are met. (
page 22)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on screen • Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5000
feet/1500 meters or lower. Using the projector at altitudes less than approximately 5000 feet/1500 meters and setting
to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
(
page 65)
Image is scrolling verti-
cally, horizontally or both
Use the appropriate source button on the remote control to select your source. (
page 18)
Adjust the computer image manually with the [HORIZONTAL] and [VERTICAL] in [ADJUST]
[IMAGE OPTIONS]
in the menu. ( page 57)
Remote control does not
work
Install new batteries. (
page 8)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. (
page 8)
Indicator is lit or blinking See the POWER/STATUS/LAMP Indicator. ( page 76)
Cross color in RGB mode Press the AUTO ADJ. button on the remote control (SELECT button on the projector cabinet). ( page 26)
Adjust the computer image manually with [CLOCK] and [PHASE] in [ADJUST]
[IMAGE OPTIONS] in the menu. (
page 56)
Formoreinformationcontactyourdealer.
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np41 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np41 in the language / languages: English as an attachment in your email.

The manual is 8,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np41

Nec np41 User Manual - German - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info