215920
158
Zoom out
Zoom in
Previous page
1/183
Next page
144
9. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Lamp Indicator
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light
Normal
Lamp has reached its end of life. Lamp
replacement message will be displayed.
Lamp has been used beyond its limit.
The projector will not turn on until the
lamp is replaced.
Lamp is in Eco mode
Red
Red
Green
Indicator Condition
Projector Condition Note
Off
Blinking light
Steady light
Green
Orange
Green
Orange
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
The main power is off
The projector is getting ready to turn on.
Off Timer (Off Time) is activated.
The projector is cooling down.
The Program Timer is activated.
The projector is turned on.
The projector is in Standby.
Wait for a moment.
Wait for a moment.
Status Indicator
Indicator Condition
Projector Condition Note
Off
Normal
Blinking light
Steady light
Red
Green
Orange
Orange
Green
1 cycle (0.5 sec On,
2.5 sec Off)
2 cycle (0.5 sec On,
0.5 sec Of)
4 cycle (0.5 sec On,
0.5 sec Off)
6 cycle (0.5 sec On,
0.5 sec Off)
1 cycle (0.5 sec On,
2.5 sec Off)
Reattach the lamp cover correctly.
(
page 138)
The projector is overheated. Move
the projector to a cooler location.
Fans will not work correctly.
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
Both the built-in wired LAN and the
wireless LAN cannot be connected to
the same network at the same time.
To use both built-in wired LAN and
wireless LAN at the same time, con-
nect them to different networks.
(
page 113, 114)
You have pressed cabinet button
when Control Panel Lock is on.
(
page 119)
Lamp cover error
Temperature error
Fan error
Lamp error
Re-firing the lamp
Network conflict
Control Panel Lock is on
The projector is in Standby.
Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
Unplug the power cable after the cooling fans stop.
Move the projector to a cooler location if the room where you are presenting is particularly too warm.
Clean the ventilation holes if they are clogged with dust.
Wait about 60 minutes until the inside of the projector becomes cool enough.
Replace the lamp.
(
page 136)
Replace the lamp.
(
page 136)
158


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np3250w at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np3250w in the language / languages: English as an attachment in your email.

The manual is 13,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np3250w

Nec np3250w User Manual - German - 183 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info