215365
150
Zoom out
Zoom in
Previous page
1/172
Next page
136
9. Appendix
Common Problems & Solutions
(
“Power/Status/Lamp Indicator” on page 135)
Problem Check These Items
Does not turn on Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. (
page 22, 23)
Ensure that the lamp cover is installed correctly. (
page 129)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end
of its life. If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
page 124)
The lamp may fail to light. Wait a full minute and then turn on the power again.
• Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without
setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this
happens, wait a couple minutes and turn on the projector. (
page 118)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before
the projector has cooled down, the fan will run a short time before the lamp will turn on.
Will turn off Ensure that the [OFF TIMER], [PROGRAM TIMER] or [AUTO POWER OFF] is off. (
page
93, 118)
No picture Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COM
-
PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the NETWORK button on the remote control
to select your source. (
page
25)
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. (
page
82)
Check to see if the image is muted. (
page
35)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. (
page
124)
Enter your registered keyword if the Security function is enabled. (
page
45)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turn
-
ing on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-
saver or power management software.
See also the next page.
Color tone or hue is
unusual
Check if an appropriate color is selected in [WALL COLOR]. If not, select an appropriate option. (
page 92)
Adjust [HUE] in [ADJUST]. (
page 82)
Image isn’t square to
the screen
Reposition the projector to improve its angle to the screen. (
page 26)
Use the 3DReform function to correct the trapezoid distortion. (
page 30)
Picture is blurred Adjust the focus. (
page
28)
Reposition the projector to improve its angle to the screen. (
page
26)
Ensure that the distance between the projector and screen is within the adjustment range of the lens. (
page
130, 132)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned
on. Should this happen, let the projector stand until there is no condensation on the lens.
Flicker appears on
screen
• Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately
5500 feet/1600 meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600
meters and setting to [HIGH ALTITUDE] can cause the lamp to overcool, causing the image to flicker.
Switch [FAN MODE] to [AUTO]. (
page 118)
Image is scrolling
vertically, horizontally or
both
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPUTER 1, the COM-
PUTER 2, the COMPUTER 3, the COMPONENT, the VIEWER or the NETWORK button on the remote control
to select your source (Video, S-Video, Computer, Component, Viewer or NETWORK). (
page 25)
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
[IMAGE OPTIONS]. (
page 83)
Remote control does
not work
Install new batteries. (
page 10)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. (
page 10)
Check if one or more remote sensors are enabled. Select [SETUP]
[INSTALLATION(2)]
[REMOTE
SENSOR] from the menu. See page
116.
If the remote control cable plug is inserted into the REMOTE mini jack, the remote control does not function
wirelessly. See page
11.
Make sure that the remote control’s ID corresponds with the projector’s ID.
• Selecting [ON] for [CONTROL ID] will not make the remote control supplied with the projector inoperable.
Indicator is lit or blinking See the POWER/STATUS/LAMP Indicator. (
page 135)
Vertical stripes in RGB
mode
Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. (
page
32)
Adjust the computer image manually with the [CLOCK]/[PHASE] in [ADJUST]
[IMAGE OPTIONS]. (
page 83)
USB mouse does not
work
Make sure that your USB mouse is properly connected to the projector. (
page
37)
The projector may not support some brands of a USB mouse.
Some menu items cannot be operated with a USB mouse.
For more information contact your dealer.
150


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np3151w at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np3151w in the language / languages: English as an attachment in your email.

The manual is 17,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np3151w

Nec np3151w User Manual - German - 169 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info