215596
92
Zoom out
Zoom in
Previous page
1/109
Next page
83
7. Appendix
Common Problems & Solutions ( “Power/Status/Lamp Indicator” on page 82.)
Does not turn on
or shut down
Will turn off
No picture
Picture suddenly
becomes dark
Color tone or hue is
unusual
Image isn’t square to
the screen
Picture is blurred
Flicker appears on
screen
Image is scrolling
vertically, horizontally
or both
Remote control does
not work
Indicator is lit or blinking
Cross color in RGB
mode
Problem Check These Items
For more information contact your dealer.
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. ( pages 25 and 38)
Ensure that the lamp cover is installed correctly. (
page 81)
Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if the lamp usage exceeds 3100 hours (up to 4100 hours : Eco mode). If so, replace the lamp.
After replacing the lamp, reset the lamp hours used. (
page 75)
The lamp may fail to light. Wait a full minute and then turn on the power again.
Set [FAN MODE] to [HIGH ALTITUDE] when using the projector at altitudes approximately 5500 feet/1600
meters or higher. Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting
to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down. If this happens,
wait a couple minutes and turn on the projector. ( page 69)
Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before
the projector has cooled down, the fan will run a short time before the lamp will turn on.
Ensure that the [OFF TIMER] or [AUTO POWER OFF] is off. ( page 71, 72)
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). ( page 29) If there is still no picture, press the button again.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. (
page 57)
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the [RESET] in the Menu. (
page 75)
Enter your registered keyword if the Security function is enabled. (
page 42)
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning
on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software.
See also the
next page.
Check if the projector is in the Forced ECO mode because of too high ambient temperature. If this is the case,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]. ( page 69)
Check if an appropriate color is selected in [WALL COLOR]. If so, select an appropriate option. ( page 64)
Adjust [HUE] in [PICTURE]. (
page 57)
Reposition the projector to improve its angle to the screen. ( page 30)
Use the Keystone correction function to correct the trapezoid distortion. (
page 34)
Adjust the focus. ( page 33)
Reposition the projector to improve its angle to the screen. (
page 30)
Ensure that the distance between the projector and screen is within the adjustment range of the lens.
( page 15)
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Set [FAN MODE] to other than [HIGH ALTITUDE] mode when using the projector at altitudes approximately 5500 feet/1600
meters or lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH
ALTITUDE] can cause the lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO]. ( page 69)
Use the COMPUTER1, the COMPUTER2, the VIDEO or the S-VIDEO button on the remote control to select
your source (Computer, Video or S-Video). ( page 29)
Adjust the computer image manually with the Horizontal/Vertical in the [IMAGE OPTIONS]. (
page 59)
Install new batteries.( page 10)
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. (
page 10)
See the POWER/STATUS/LAMP Indicator. ( page 82)
Press the AUTO ADJ. button on the projector cabinet or the remote control. ( page 37)
Adjust the computer image manually with [CLOCK]/[PHASE] in [IMAGE OPTIONS] in the menu. ( page 58)
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np300 in the language / languages: English as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np300

Nec np300 User Manual - German - 109 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info