216098
141
Zoom out
Zoom in
Previous page
1/183
Next page
127
6. Using On-Screen Menu
Enabling Power Management [AUTO POWER OFF]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5min.,
10min., 20min., 30min.) if there is no signal received by any input.
Enabling High Speed Fan Mode [FAN MODE]
This option allows you to select three modes for fan speed: Auto mode, High speed mode, and High Altitude mode.
AUTO .....................
The built-in fans automatically run at a variable speed according to the internal temperature.
HIGH ...................... The built-in fans run at high speed.
HIGH ALTITUDE ..... The built-in fans run at a high speed. Select this option when using the projector at altitudes approximate-
ly 5500 feet/1600 meters or higher.
When you wish to cool down the temperature inside the projector quickly, select [HIGH].
NOTE:
It is recommended that you select High speed mode if you use the projector non-stop for consecutive days.
Using the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [HIGH ALTITUDE] can cause
the projector to overheat and the protector could shut down. If this happens, wait a couple minutes and turn on the projector.
Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [HIGH ALTITUDE] can cause the
lamp to overcool, causing the image to flicker. Switch [FAN MODE] to [AUTO].
Your setting will not be affected even when [RESET] is done from the menu.
Selecting Default Source [DEFAULT SOURCE SELECT]
You can set the projector to default to any one of its inputs each time the projector is turned on.
LAST ......................
Sets the projector to default to the previous or last active input each time the projector is turned on.
AUTO ..................... Searches for an active source in order of COMPUTER1
COMPUTER2
COMPUTER3
COMPONENT
VIDEO
S-VIDEO
VIEWER
COMPUTER1 and displays the first found source.
COMPUTER 1 ........ Displays the RGB source from the COMPUTER 1 IN connector every time the projector is turned on.
COMPUTER 2 ........ Displays the RGB source from the COMPUTER 2 IN connector every time the projector is turned on.
COMPUTER 3 ........ Displays the RGB source from the COMPUTER 3(DVI-D) IN connector every time the projector is turned
on.
COMPONENT ......... Displays the component source from the COMPONENT IN connector every time the projector is turned
on.
VIDEO ....................
Displays the Video source from the VIDEO IN connector every time the projector is turned on.
S-VIDEO ................ Displays the Video source from the S-VIDEO IN connector every time the projector is turned on.
VIEWER ................. Displays slides or plays back movie files from the USB memory device or a shared folder connected to
LAN every time the projector is turned on.
NETWORK ............. Displays a signal from LAN port (RJ-45) or the USB Wireless LAN Unit.
Selecting Signal Format [SIGNAL SELECT]
COMPUTER 1/2
Allows you to set [COMPUTER 1] and [COMPUTER 2] to automatically detect an incoming RGB or component
source such as a computer or DVD player. However there may be some RGB and component signals that the
projector is unable to detect. In this case, select [RGB] or [COMPONENT].
Selecting [COLOR SYSTEM]
This feature enables you to select video standards manually.
Normally select [AUTO]. Select the video standard from the pulldown menu. This must be done for Video and S-Vid-
eo Connectors separately.
141


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec np1250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec np1250 in the language / languages: English as an attachment in your email.

The manual is 13,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec np1250

Nec np1250 User Manual - German - 183 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info