493598
228
Zoom out
Zoom in
Previous page
1/235
Next page
216
9. Appendix
Common Problems & Solutions
(“Power/Status/LampIndicator”onpage214.)
Problem CheckTheseItems
Does not turn on
or shut down
• Checkthatthepowercordispluggedinandthatthepowerbuttonontheprojectorcabinetortheremote
control is on� ( pages 13, 14)
• Ensurethatthelampcoverisinstalledcorrectly.( page 161)
• Checktoseeiftheprojectorhasoverheated.Ifthereisinsufcientventilationaroundtheprojectororifthe
room where you are presenting is particularly warm, move the projector to a cooler location�
• Checktoseeifyoucontinuetousetheprojectorforanother100hoursafterthelamphasreachedtheend
of its life� If so, replace the lamp� After replacing the lamp, reset the lamp hours used� ( page 116)
• Thelampmayfailtolight.Waitafullminuteandthenturnonthepoweragain.
• Set[FANMODE]to[HIGHALTITUDE]whenusingtheprojectorataltitudesapproximately5500feet/1600
meters or higherUsing the projector at altitudes approximately 5500 feet/1600 meters or higher without
setting to [HIGH ALTITUDE] can cause the projector to overheat and the projector could shut down� If this
happens, wait a couple minutes and turn on the projector� ( page 108)
If you turn on the projector immediately after the lamp is turned off, the fans run without displaying an image
for some time and then the projector will display the image� Wait for a moment�
Will turn off
• Ensurethatthe[OFFTIMER],[AUTOPOWEROFF]or[PROGRAMTIMER]isoff.( page 101, 111)
No picture
•
Check if the appropriate input is selected� ( page 16) If there is still no picture, press the SOURCE button
or one of the input buttons again�
• Ensureyourcablesareconnectedproperly.
• Usemenustoadjustthebrightnessandcontrast.( page 93)
• Ensurethatthelenscoverisopen.( page 14)
• Resetthesettingsoradjustmentstofactorypresetlevelsusingthe[RESET]intheMenu.( page 116)
• EnteryourregisteredkeywordiftheSecurityfunctionisenabled.( page 37)
• If the HDMI input or the DisplayPort signal cannot be displayed, try the following�
- Reinstall your driver for the graphics card built in your computer, or use the updated driver
For reinstalling or updating your driver, refer to the user guide accompanied with your computer or graphics
card, or contact the support center for your computer manufacturer
Install the updated driver or OS on your own responsibility
We are not liable for any trouble and failure caused by this installation�
• BesuretoconnecttheprojectorandnotebookPCwhiletheprojectorisinstandbymodeandbeforeturning
on the power to the notebook PC�
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up�
* If the screen goes blank while using your remote control, it may be the result of the computer’s screen-saver
or power management software�
• Seealsothepage218
Picture suddenly
becomes dark
• CheckiftheprojectorisintheForcedECOmodebecauseoftoohighambienttemperature.Ifthisisthecase,
lower the internal temperature of the projector by selecting [HIGH] for [FAN MODE]� ( page 108)
Color tone or hue is
unusual
• Checkifanappropriatecolorisselectedin[WALLCOLOR].Ifso,selectanappropriateoption.( page
101)
• Adjust[HUE]in[PICTURE].( page 93)
Image isn’t square to
the screen
• Repositiontheprojectortoimproveitsangletothescreen.( page 17)
• UsetheKeystonecorrectionfunctiontocorrectthetrapezoiddistortion.( page 22)
Picture is blurred
• Adjustthefocus.( page 19)
• Repositiontheprojectortoimproveitsangletothescreen.( page 17)
• Ensurethat the distance betweenthe projector and screen is within the adjustment range of the lens.
( page 201)
• Has the lens been shifted by an amount exceeding the guaranteed range? ( page 205)
• Condensationmayformonthelensiftheprojectoriscold,broughtintoawarmplaceandisthenturnedon.
Should this happen, let the projector stand until there is no condensation on the lens�
228


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec NP-PA500X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec NP-PA500X in the language / languages: English as an attachment in your email.

The manual is 15,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info