654030
137
Zoom out
Zoom in
Previous page
1/155
Next page
127
8. Appendix
1 Troubleshooting
Thissectionhelpsyouresolveproblemsyoumayencounterwhilesettinguporusingtheprojector.
Indicator Messages
Power Indicator
Indicator Condition ProjectorCondition Note
Off The main power is off
Blinking light Blue
0�5 sec On,
0�5 sec Off
The projector is getting ready to turn on� Wait for a moment�
2�5 sec On,
0�5 sec Off
Off Timer is enabled�
Steady light Blue The projector is turned on�
Orange [NORMAL] is selected for [STANDBY MODE]
Red [POWER-SAVING] is selected for [STANDBY
MODE]
Status Indicator
Indicator Condition ProjectorCondition Note
Off
Normal or Standby ([POWER-SAVING] for
[STANDBY MODE])
Blinking light Red
1 cycle (0�5 sec
On, 2�5 sec Off)
Lamp cover error or lamp housing error Replace the lamp cover or lamp housing correctly
2 cycle (0�5 sec
On, 0�5 sec Off)
Temperature error The projector is overheated� Move the projector to
a cooler location�
3 cycle (0�5 sec
On, 0�5 sec Off)
Power error Power unit is not working properly Contact your
dealer
4 cycle (0�5 sec
On, 0�5 sec Off)
Fan error Fans will not work correctly
6 cycle (0�5 sec
On, 0�5 sec Off)
Lamp error Lamp fails to light� Wait a full minute and then turn
on again�
9 cycle (0�5 sec
On, 0�5 sec Off)
[DYNAMIC CONTRAST] error Dynamic Contrast function is not working properly�
Contact your dealer
Orange
1 cycle (05 sec
On, 2�5 sec Off)
Network conflict
Both the built-in wired LAN and the wireless LAN can-
not be connected to the same network at the same
time�
To use both built-in wired LAN and wireless LAN at
the same time, connect them to different networks�
Green Re-firing the lamp (The projector is cooling
down�)
The projector is re-firing�
Wait for a moment�
Steadylight
Green
Standby ([NORMAL] for [STANDBY MODE])
Orange
CONTROL PANEL LOCK is on� You have pressed cabinet button when Control
Panel Lock is on�
CONTROL ID error Remote control ID and projector ID are not
matched�
Lamp Indicator
Indicator Condition ProjectorCondition Note
Off Normal
Blinking light Red
Lamp has reached its end of life� Lamp replace-
ment message will be displayed�
Replace the lamp�
Steady light Red Lamp has been used beyond its limitThe projector
will not turn on until the lamp is replaced�
Replace the lamp�
Green [ECO MODE] is set to [AUTO ECO], [ECO1], or
[ECO2]
Over-TemperatureProtection
Ifthetemperatureinsidetheprojectorrisestoohigh,theover-temperatureprotectorwillautomaticallyturnoffthelamp
withtheSTATUSindicatorblinking(2-cycleOnandOff.)
Shouldthishappen,dothefollowing:
• Unplugthepowercordafterthecoolingfansstop.
• Movetheprojectortoacoolerlocationiftheroomwhereyouarepresentingisparticularlytoowarm.
• Cleantheventilationholesiftheyarecloggedwithdust.
• Waitabout60minutesuntiltheinsideoftheprojectorbecomescoolenough.
137


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec NP-M260W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec NP-M260W in the language / languages: English as an attachment in your email.

The manual is 9,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec NP-M260W

Nec NP-M260W User Manual - German - 155 pages

Nec NP-M260W Quick start guide - Dutch, Danish, Polish, Turkish, Norwegian, Finnish - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info