Manual Nec multisync lcd1770nx bk (page 18 of 18) (English)

214152

Zoom out

Zoom in

1/18

MultiSync LCD1770NX

User’s Manual

Index

Warning, Caution .........................................................................................................................English-1

Declaration ...................................................................................................................................English-1

Canadian Department of Communications Compliance Statement ............................................English-2

Declaration of Conformity ............................................................................................................English-2

Contents .......................................................................................................................................English-3

Quick Start ...................................................................................................................................English-4

Controls........................................................................................................................................English-8

Recommended use ....................................................................................................................English-10

Specifications .............................................................................................................................English-12

Features .....................................................................................................................................English-13

Troubleshooting ..........................................................................................................................English-14

TCO’03 ....................................................................................................................................... English-15

Manufacturer’s Recycling and Energy Information..................................................................... English-16

English

English-1

WARNING

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM

WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE

POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause

electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit

has been included. Therefore, it should be read carefully in order to avoid any problems.

Caution:

When operating the MultiSync LCD1770NX with a 220-240V AC power source in Europe, use the power cord provided with

the monitor.

In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment.

If a power cord is not supplied with this equipment please contact your supplier.

When operating the MultiSync LCD1770NX with a 220-240V AC power source in Australia, use the power cord provided with

the monitor. If a power cord is not supplied with this equipment please contact your supplier.

For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by and

complies with the safety standard of your particular country.

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT

USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS

THE PRONGS CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

Declaration

Declaration of the Manufacturer

We hereby certify that the colour monitor

MultiSync LCD1770NX (L174F) is in

compliance with

Council Directive 73/23/EEC:

– EN 60950-1

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

and marked with

NEC Display Solutions, Ltd.

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ENERGY STAR is a

U.S. registered trademark.

OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.

ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway,

Spain, Sweden, U.K.

NaViSet is a trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.

MultiSync is a registered trademark of NEC Display Solutions, Ltd. in the countries of U.K., Italy, Austria, Netherlands, Switzerland,

Sweden, Spain, Denmark, Germany, Norway and Finland.

All other brands and product names are trademarks or registered trademarks of their respective owners.

As an ENERGY STAR

Partner, NEC Display Solutions of America, Inc. has determined that this product meets the ENERGY STAR guidelines

for energy efficiency. The ENERGY STAR emblem does not represent EPA endorsement of any product or service.

English-2

Canadian Department of Communications Compliance

Statement

DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.

FCC Information

1. Use the attached specified cables with the MultiSync LCD1770NX (L174F) colour monitor so as not to interfere with

radio and television reception.

(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A.,

and meet the following condition.

Power supply cord Non shield type, 3-conductor

Length 2.0 m

Plug shape

U.S.A

(2) Please use the supplied shielded video signal cable. Use of other cables and adapters may cause interference

with radio and television reception.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/television technician for additional

suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:

“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government

Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.

Declaration of Conformity

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

U.S. Responsible Party: NEC Display Solutions of America, Inc.

Address: 500 Park Blvd, Suite 1100

Itasca, Illinois 60143

Tel. No.: (630) 467-3000

Type of Product: Display Monitor

Equipment Classification: Class B Peripheral

Model: MultiSync LCD1770NX (L174F)

We hereby declare that the equipment specified above conforms

to the technical standards as specified in the FCC Rules.

English

English-3

MultiSync LCD1770NX

Contents

Your new NEC MultiSync LCD monitor box* should contain the following:

• MultiSync LCD1770NX monitor with tilt/swivel/pivot/height adjust stand

• Power Cord

•Video Signal Cable

• User’s Manual

• Cable Cover

• CD ROM (includes complete User’s Manual in PDF format).

To see the User’s Manual, Acrobat Reader 4.0 must be installed on your PC.

Remember to save your original box and packing material to transport or ship the monitor.

Power Cord

User’s Manual 15-pin mini D-SUB male to

15-pin mini D-SUB male

CD-ROM

Cable Cover

English-4

Quick Start

To attach the MultiSync LCD monitor to your system, follow these instructions:

1. Turn off the power to your computer.

2. For the PC or MAC with DVI digital output: Connect the DVI signal cable (not included) to the connector of the display

card in your system (Figure A.1). Tighten all screws.

For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your

system (Figure A.2). Tighten all screws.

For the MAC: Connect the Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to

the Macintosh cable adapter (Figure B.1). Tighten all screws.

NOTE: Some Macintosh systems do not require a Macintosh cable adapter.

3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position (Figure C.1).

4. Connect all cables to the appropriate connectors (Figure C.1).

NOTE: If connecting both DVI and D-sub cable, the DVI cable must be connected along side the rib on the power cord side

(Figure C.1).

5. For successful cable management, place the cables in this order into the cable management: power cable and DVI cable

(Figure C.2).

Figure A.1 Figure B.1

Macintosh

Cable Adapter

(not included)

Figure A.2

DVI signal cable

(not included)

Highest

Stand

Position

DVI Cable

30˚ Tilt

DVI Cable (Top)

Power Cable

(Bottom)

Figure C.1 Figure C.2

English

English-5

Insert Top First

Then Bottom

6. Place DVI cable and power cable into the specific hooks indicated in Figure C.3.

7. Place the D-Sub into the specific hooks indicated in Figure C.4.

8. Make sure all cables are resting flat against the stand (Figure C.4).

9. Hold the all cables firmly and place the cable cover onto the stand (Figure D.1). To remove the cable cover, lift the cover

off as shown in Figure D.2.

10. Connect the power cord to the power outlet (Figure E.1).

NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.

11. The vacation switch on the back side of the monitor must be turned on (Figure E.1). Turn on the monitor with the front

power button and the computer.

NOTE: The vacation switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be turned on

using the front button. DO NOT switch on/off repeatedly.

12. No-Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for most timings.

For further adjustments, use the following OSM controls:

• Auto Adjust Contrast (Analog input only)

• Auto Adjust (Analog input only)

Refer to the Controls section of this User’s Manual for a full description of these OSM controls.

NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.

Figure D.1 Figure D.2

DVI Cable

Ridge

Power Cable

D-Sub Cable

Figure C.3 Figure C.4

Figure E.1

ON Position

OFF Position

Power Button

Vacation Switch

English-6

Figure S.1

Remove Monitor Stand for Mounting

To prepare the monitor for alternate mounting purposes:

1. Place hands on each side of the monitor and lift up to the highest position. Remove the cable cover (Figure S.1).

2. Disconnect all cables.

3. Place monitor face down on a non-abrasive surface (Figure S.2).

4. Remove the 2 screws connecting the stand to the monitor (Figure S.2).

Figure RL.1

Raise and Lower Monitor Screen

The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lift or lower to

the desired height (Figure RL.1).

NOTE: Handle with care when raising or lowering the monitor screen.

Tilt and Swivel

Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).

NOTE: Handle with care when tilting and swivelling the monitor screen.

Figure TS.1

Figure S.2

English

English-7

Figure S.3

Figure S.4

5. Lift up the stand to unlatch the upper hooks and remove the stand (Figure S.3).

6. Remove the 2 screws on the top of the monitor (Figure S.4). The monitor is now ready for mounting in an alternate

manner.

7. Connect the cables to the back of the monitor.

8. Reverse this process to re-attach stand.

NOTE: Use only VESA-compatible alternative mounting method.

Handle with care when removing stand.

Flexible Arm Installation

This LCD monitor is designed for use with a flexible arm. To mount the monitor to a flexible arm:

1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand.

2. Using the 4 screws from the stand removal and attach the arm to the monitor (Figure F.1).

NOTE: The LCD monitor should only be used with an approved arm (e.g. GS mark). To meet the safety requirements, the

monitor must be mounted to an arm, which guaranties the necessary stability under consideration of the weight of

the monitor.

Thickness of Bracket (Arm)

2.0~3.2mm

4 Screws (4M)

(Max Depth: 8.5mm)

Weight of LCD assembly: 4.3kg (MAX)

100mm

Figure F.1

English-8

Exits the OSM controls.

Exits to the OSM main menu.

Moves the highlighted area left/right to select control menus.

Moves the bar left/right to increase or decrease the adjustment.

Moves the highlighted area down/up to select one of the controls.

Active Auto Adjust function. Enter the OSM sub menu.

Resets the highlighted control menu to the factory setting.

Button

MENU/EXIT

Left/Right

Down/Up

SELECT

RESET

Controls

OSM (On-Screen Manager) control buttons on the front of the monitor

function as follows:

To access OSM menu, press any of the control buttons (MENU/EXIT, Left, Right, Down, Up).

To change signal input, press the SELECT button.

NOTE: OSM must be closed in order to change signal input.

NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the

RESET function by pressing the MENU/EXIT button.

Brightness/Contrast Controls

BRIGHTNESS

Adjusts the overall image and background screen brightness.

CONTRAST

Adjusts the image brightness in relation to the background.

AUTO CONTRAST (Analog input only)

Adjusts the image displayed to optimal settings.

Auto Adjust (Analog input only)

Automatically adjusts the Image Position, H. Size and Fine settings.

Image Controls (Analog input only)

LEFT / RIGHT

Controls Horizontal Image Position within the display area of the LCD.

DOWN / UP

Controls Vertical Image Position within the display area of the LCD.

H.SIZE

Adjusts the horizontal size by increasing or decreasing this setting.

FINE

Improves focus, clarity and image stability by increasing or decreasing this setting.

English-16

NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s

top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-

friendly products, and always strive to help define and comply with the latest independent standards from agencies such as

ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

Disposing of your old NEC product

The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of

material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely

disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling

procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end

of its life.

All required information concerning the disposal of the product and country-specific information on recycling facilities can be

found on our following websites:

http://www.nec-display-solutions.com/greencompany/ (in Europe),

http://www.nec-display.com (in Japan) or

http://www.necdisplay.com (in USA).

Energy Saving

This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)

Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.

Mode Power consumption LED colour

Normal Operation Approx. 36W Green

Energy Saving Mode Less than 2W Amber

Off Mode Less than 1W Unlit

Manufacturer’s Recycling and Energy Information

WEEE Mark (European Directive 2002/96/EC)

Within the European Union

EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic

products carrying the mark (left) must be disposed of separately from normal household waste. This includes

monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your

NEC display products, please follow the guidance of your local authority, or ask the shop where you

purchased the product, or if applicable, follow any agreements made between yourself and NEC.

The mark on electrical and electronic products only applies to the current European Union Member States.

Outside the European Union

If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local

authority so as to comply with the correct disposal method.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nec multisync lcd1770nx bk in the language / languages: English as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nec multisync lcd1770nx bk Manual

Product: