493585
25
Zoom out
Zoom in
Previous page
1/69
Next page
E-25
Auto 3D Reform
Auto 3D Reform automatically corrects distortion by sensing the outline
or outer frame of your screen with the projector’s built-in image sensor
to project an image within the screen.
NOTE:
The Auto 3D Reform feature supports screen sizes between 30” and 200”.
If the screen has the same brightness as its background, the built-in image
sensor on the front of the projector can fail to recognize the outline or outer
frame of the screen.
Should this happen, the Auto 3D Reform feature cannot function.
If irregular colors, flaw or change of color are seen on the screen, the built-in
sensor can mistakenly interpret the outline or outer frame of the screen.
If there is an object between the built-in sensor and the screen, the screen
cannot be recognized.
The Auto 3D Reform feature does not support reflective screens. Matt type or
beads type screens are recommended.
Executing the Auto 3D Reform feature
1. Project an image.
See the user’s manual or the quick connect guide for projecting an
image.
2. Press the 3D REFORM button.
The 3D Reform (Cornerstone) screen is displayed.
Projected area
3. Press and hold the AUTO ADJUST button for a minimum of 2 sec-
onds.
A guide pattern that shows available area for Auto 3D Reform is dis-
played.
* The AUTO ADJ. button on the remote control can also be used for
this purpose.
Screen’s outer frame
4. Place the projector adjusting its orientation and the angle so that the
outline (outer frame) of the screen can be positioned within the gray
area of the projected guide pattern.
5. Highlight [Start] and press the ENTER button.
The Auto 3D Reform feature has been executed. Processing takes
about 20 seconds
*To cancel, use the SELECT
̇
or
̈
button to highlight [Cancel] and
press the ENTER button.
NOTE:
* When “4:3 Fill" is selected in “Aspect”, the Auto 3D Reform feature is not
available.
* If the screen’s outer frame is larger than gray area of the guide pattern as
shown, the Auto 3D Reform feature does not function.
* In the Auto 3D Reform mode, when controlling the projector using PC con-
trol, you might not be able to make correction. (The projector can be oper-
ated with Dynamic Image Utility 2.0, Image Express Utility 1.0 and HTTP
Server function.)
Not recommended
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec MT1075 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec MT1075 in the language / languages: English as an attachment in your email.

The manual is 3,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec MT1075

Nec MT1075 User Manual - German - 69 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info