654051

Nec MT1045E Manual

12
Zoom out
Zoom in
Previous page
1/42
Next page
E–12
2. INSTALLATION
This section describes how to set up your MultiSync MT840/MT1040/
MT1045 projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync MT840/MT1040/MT1045 Projector is simple to set
up and use. But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying the Projector: Always carry your projector by the handle.
Ensure that the power cable and any other cables connecting to video
sources are disconnected before moving the projector.
When moving the projector or when it is not in use, cover the lens
with the lens cap.
Screen
Top view
Screen
Side view
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal distance
from the screen or wall so you realize the size image you want.
(Avoid having bright room lighting or sun light directly on the
screen or wall where you’ll be projecting the image.)
4. Move the projector left or right to center the image horizontally
on the screen.
5. To center the image vertically, lift the front edge of the projector
and press the One-Touch Tilt button on the front-left side of the
projector to release the Front Adjustable foot.
(There is approximately 5 degrees of up and down adjustment for
the front of the projector.)
Selecting a Location
The further your projector is from the screen or wall, the larger the
image. The minimum size the image can be is approximately 30"
(0.76 m) measured diagonally when the projector is roughly 4 feet
(1.3 m) from the wall or screen. The largest the image can be is 300"
(7.6 m) when the projector is about 36.8 feet (11.2 m) from the wall
or screen.
Lens cap
String
Rivet
Attaching the lens cap to the lens hood
with the supplied string and rivet.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE AUTO ADJUST
USB
AC IN
2. Connect the power cable, remove the lens cap and turn the projec-
tor on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELEC
T
PO
W
ER
STATUS
O
N
/
O
FF
SO
U
RCE
AU
TO
AD
JU
ST
AC IN
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE
AUTO ADJUST
AC IN
Press and hold the Tilt but-
ton on the left side of the
projector.
Lift the front edge of the projec-
tor to the height you want, and
release the button to lock the
Adjustable Tilt Foot.
Adjusting the Tilt Foot
To fine-tune the image’s position vertically on the screen,
rotate the foot. Each of the rear feet height can be changed
up to 0.6” (4mm).
6. If the projected image does not appear square to the screen then
use keystone correction for proper adjustment.
7. Adjust the size of the image using the Zoom ring on the lens.
Carrying handle
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec MT1045E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec MT1045E in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec MT1045E

Nec MT1045E User Manual - German - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info