654052
15
Zoom out
Zoom in
Previous page
1/42
Next page
E–15
Remote Control Guideline for the Remote Control
1. Plug the supplied serial cable with the mouse output port of the
projector into your computer’s mouse port and restart your com-
puter to gain remote mouse control.
2. When using the remote control’s built-in infrared mouse on a laptop
computer, the laptop’s mouse, trackball or trackpad will be dis-
abled. Disconnect the serial cable from the mouse output port and
restart your computer to regain trackball or trackpad mouse con-
trol.
3. If the screen goes blank while using your remote control, it may
be the result of the computer’s screen-saver or power manage-
ment software.
4. If you accidentally hit the OFF button on the remote control, wait
one full minute and then press the ON button to resume.
Connecting Your PC or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync
MT840 (SVGA)/MT1040 and MT1045 (XGA) projector will enable
you to project your computer’s screen image for an impressive pre-
sentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the signal cable that’s supplied to connect your PC or
Macintosh computer to the projector. For older Macintosh, use
the supplied pin adapter to connect to your Mac's video port.
NOTE:The new Macintosh computer such as G3 will have the 15
pin HD connector. The MT840/MT1040/MT1045's "Plug and Play"
data will be downloaded to the Macintosh. Therefore, the Mac
adapter will not be necessary.
3. Turn on the projector and the computer.
4. If the projector goes blank after a period of inactivity, it may be
caused by a screen saver installed on the computer you’ve con-
nected to the projector.
Connecting An External Monitor
You can connect a separate, external monitor to your projector to
simultaneously view on a monitor the image you're projecting. To do
so:
1. Turn off the power to your projector, monitor and computer, docu-
ment camera or video source.
2. Use a 15-pin cable to connect your monitor to the RGB Monitor
Output (Mini D-Sub 15 pin) connector on your projector.
3. Turn on the projector, monitor and the computer, document cam-
era or video source.
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the
notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.
PC CONTROL
REMOTE
CONTROL
INPUT
MOUSE
OUTPUT
S-VIDEO
VIDEO
AUDIO RGB INPUT
AUDIO MONITOR
OUTPUT
RGB OUTPUT
L
/
MONO
R
Wiring Diagram
Optional Component V cable
To video, S-video, and audio
inputs on the projector.
Supplied mouse adapter (For Macintosh)
Supplied mouse adapter
(For IBM PS/2)
Pin adapter for Macintosh
(supplied)
Signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is
recommended that you use a commercially available
distribution amplifier if connecting a signal cable longer
than the supplied one.
IBM VGA or Compatibles
(Desktop type or notebook type)
Macintosh or Compatibles
(Desktop type or notebook type)
Document Camera
DVD Player (with component output)
VCR, DVD Player or LaserDisc Player
Supplied serial cable
Monitor
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec MT1040E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec MT1040E in the language / languages: English as an attachment in your email.

The manual is 1,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec MT1040E

Nec MT1040E User Manual - German - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info