493575
52
Zoom out
Zoom in
Previous page
1/59
Next page
E–52
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp.
Replacing the Lamp
After your lamp has been operating for 1000 hours or longer, the
“Status” light in the cabinet will go on and the message will appear.
Even though the lamp may still be working, replace it at 1000 hours
to maintain optimal projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn the projector off, wait 90
seconds, and then disconnect the power cable. Allow at least
one hour for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
The projector will turn off and go into stand by mode after 1100
hours of service. If this happens, be sure to replace the lamp. If
you continue to use the lamp after 1000 hours of use, the lamp
bulb may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury.
If this happens, contact your NEC dealer for lamp replacement.
To replace the lamp:
1 Loosen the lamp cover screw until the screwdriver goes into a
freewheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
2 Loosen the three screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
4 Insert a new lamp housing until the lamp housing is plugged into
the socket.
A
C
IN
PC CARD
USB
AUDIO
VIDEO
S-VIDEO
RGB
PC CONTROL
A
C
IN
PC CA
RD
USB
AUD
IO
VID
EO
S
-VID
EO
RG
B
PC
CON
TROL
A
U
D
I
O
R
G
P
C
C
O
N
T
R
O
L
Interlock
3 Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical
shock. Do not attempt to circumvent this interlock.
AUDIO
RGB
PC CO
NTR
O
L
5 Secure it in place with the three screws.
A
U
D
I
O
S
-
V
I
D
E
O
R
G
B
P
C
C
O
N
T
R
O
L
6 Reattach the lamp cover.
A
U
D
IO
S
-V
ID
E
O
R
G
B
P
C
C
O
N
T
R
O
L
7 Tighten the lamp cover screw.
A
U
D
IO
R
G
B
P
C
C
O
N
T
R
O
L
8 After you install a new lamp, select the Main menu [Projector
Options] [Setup] [Page 4] [Clear Lamp Hour Meter] to
reset the lamp usage hours.
If the projector will not be turned on after using 1100 hours of
service, press and hold the [Help] button on the remote control for
ten seconds or longer to reset the lamp time clock to zero.
CAUTION: Do not use a lamp other than the NEC replacement lamp (LT50LP).
Order this from your NEC dealer.
Be sure to tighten the screws.
Be sure to tighten the screw.
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec LT85 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec LT85 in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec LT85

Nec LT85 User Manual - German - 59 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info