653981

Nec LT84 Manual

12
Zoom out
Zoom in
Previous page
1/43
Next page
E–12
2. INSTALLATION
This section describes how to set up your MultiSync LT84/LT140
projector and how to connect video and audio sources.
Setting up Your Projector
Your MultiSync LT84/LT140 Projector is simple to set up and use.
But before you get started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
Carrying The Projector: Always carry your projector in the supplied
soft carrying case.
NOTE: Do not put a notebook computer in the soft carrying case.
Doing so can cause damage to the computer. When moving the pro-
jector or when it is not in use, cover the lens cap.
Screen
Top view
Screen
Side view
Using a Tabletop or Cart
1. Place your projector on a flat level surface at the optimal distance
from the screen or wall so you realize the size image you want.
(Avoid having bright room lighting or sun light directly on the
screen or wall where you’ll be projecting the image.)
5. To center the image vertically, lift the front edge of the projector
and press the One-Push Tilt buttons on the front side of the pro-
jector, just above the feet, to release the Front Adjustable feet.
(There is approximately 5 degrees of up and down adjustment for
the front of the projector.)
6. If necessary, adjust the front or rear feet to properly position the
projected image on the screen.
If the projected image does not appear square to the screen then
use keystone correction for proper adjustment. The Lever-Type
Adjustable Rear foot height can be changed up to 3 degrees.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE AUTO
Upward
Bottom
Carrying Case
Selecting a Location
The further your projector is from the screen or wall, the larger the
image. The minimum size the image can be is approximately 25"
(0.6 m) measured diagonally when the projector is roughly 4 feet
(1.2 m) from the wall or screen. The largest the image can be is 300"
(7.6 m) when the projector is about 40 feet (12.2 m) from the wall or
screen.
Lens cap
String
Rivet
You must put the projector in the soft carrying case with
the lens upward as shown below. This is to prevent the
lens from damage.
Attaching the lens cap to
the lens hood with the sup-
plied string and rivet.
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POW
ER
STATUS
ON
/
OFF
SOURCE AUTO
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE AUTO
M
E
N
U
E
N
T
E
R
C
A
N
C
E
L
SELECT
POWER
STATUS
ON
/
OFF
SOURCE AUTO
Band
2. Connect the power cable, remove the lens cap and turn the projec-
tor on. (If no input signal is available, the projector will display a
background image.)
3. Ensure that the projector is square to the screen.
4. Move the projector left or right to center the image horizontally
on the screen.
7. Adjust the size of the image using the Zoom ring on the lens.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec LT84 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec LT84 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec LT84

Nec LT84 User Manual - German - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info