653980
34
Zoom out
Zoom in
Previous page
1/40
Next page
E-34
This section describes the simple maintenance procedures you
should follow to replace the lamp.
Replacing the Lamp
After your lamp has been operating for 1000 hours (1500 hours:
Eco mode) or longer, the “Status” indicator in the cabinet will
go on and the message will appear. Even though the lamp
may still be working, replace it at 1000 hours (1500 hours: Eco
mode) to maintain optimal projector performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has
been used. It will be extremely hot. Turn the projector
off, wait 90 seconds, and then disconnect the power
cable. Allow at least one hour for the lamp to cool
before handling.
DO NOT REMOVE ANY SCREWS except the lamp
cover screw and three lamp case screws. You could
receive an electric shock.
The projector will turn off and go into stand by mode
after 1100 hours (1600 hours: Eco mode) of service.
If this happens, be sure to replace the lamp. If you
continue to use the lamp after 1000 hours (1500
hours: Eco mode) of use, the lamp bulb may shatter,
and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may
cause injury. If this happens, contact your NEC dealer
for lamp replacement.
To replace the lamp:
1 Loosen the lamp cover screw until the screwdriver goes into
a freewheeling condition and remove the lamp cover. The
lamp cover screw is not removable.
4. MAINTENANCE
2 Loosen the three screws securing the lamp housing until
the screwdriver goes into a freewheeling condition. The three
screws are not removable.
3 Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of
electrical shock. Do not attempt to circumvent this interlock.
Interlock
4 Insert a new lamp housing until the lamp housing is plugged
into the socket.
CAUTION: Do not use a lamp other than the NEC re-
placement lamp (LT51LP). Order this from your NEC
dealer.
5 Secure it in place with the three screws.
Be sure to tighten the screws.
6 Reattach the lamp cover.
7 Tighten the lamp cover screw.
Be sure to tighten the screw.
8 After you install a new lamp, select the [Advanced Menu]
[Projector Options] [Setup] [Page 4] [Clear Lamp
Hour Meter] to reset the lamp usage hours.
If the projector will not be turned on after using 1100 hours
(1600 houres: Eco mode)of service, press and hold the [Help]
button on the remote control for ten seconds or longer to
reset the lamp time clock to zero.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec LT75Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec LT75Z in the language / languages: English as an attachment in your email.

The manual is 1,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec LT75Z

Nec LT75Z User Manual - German - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info