493579
33
Zoom out
Zoom in
Previous page
1/43
Next page
E–33
4. MAINTENANCE
This section describes the simple maintenance procedures you should
follow to replace the lamp, and replace the coin cell in the remote
control.
Replacing The Lamp
After your lamp has been operating for 1000 hours or longer, the
“Status” light in the cabinet will go on. Even though the lamp may
still be working, replace it at 1000 hours to maintain optimal projec-
tor performance.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been
used. It will be extremely hot. Turn off the power to the pro-
jector and allow at least one hour for the lamp to cool. Then
disconnect the power cable.
DO NOT REMOVE ANY SCREWS except the lamp cover
screw and three lamp case screws. You could receive an elec-
tric shock.
The projector will turn off and go into stand by mode after
1100 hours of service. If this happens, be sure to replace the
lamp. If you continue to use the lamp after 1000 hours of use,
the lamp bulb may shatter, and pieces of glass may be scat-
tered in the lamp case. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a free-
wheeling condition and remove the lamp cover. The lamp cover
screw is not removable.
2. Loosen the three screws securing the lamp housing until the screw-
driver goes into a freewheeling condition. The three screws are
not removable.
3. Remove the lamp housing by pulling out the handle.
4. Insert a new lamp housing until the lamp housing is plugged into
the socket.
5. Secure it in place with the three screws.
Be sure to tighten the three screws.
CAUTION: Do not use a lamp other than the NEC replace-
ment lamp (LT40LP).
Order this from your NEC dealer.
6. Reattach the lamp cover.
7. Tighten the lamp cover screw.
Be sure to tighten the lamp cover screw.
8. After you install a new lamp, select [Main Menu] [Projector
Options] [Setup][Page 2][Clear Lamp Hour Meter] to re-
set the lamp usage hours.
NOTE: When the lamp exceeds 1100 hours of service, the projector
cannot turn on and the menu is not displayed. If this happens, press
the Help button on the remote control for a minimum of 10 seconds
while in standby mode. When the lamp time clock is reset to zero, the
STATUS indicator goes out.
NOTE: There is an interlock on this case to prevent the risk of elec-
trical shock. Do not attempt to circumvent this interlock.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec LT140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec LT140 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec LT140

Nec LT140 User Manual - German - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info