214287
38
Zoom out
Zoom in
Previous page
1/45
Next page
E-38
TROUBLESHOOTING
Does not turn on
No picture
Image isn’t square to the
screen
Picture is blurred
Image is scrolling verti-
cally, horizontally or
both
Remote control does
not work
Indicator is lit or blink-
ing
Cross color in RGB
mode
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See page E- 17.
Check to see if the Cabinet Button Lock function is enabled.If this function is enabled, cancel it by pressing and
holding the MENU button on the cabinet for a minimum of 10 seconds or using the menu with the remote
control. See page E-33.
Ensure that the lamp cover or lamp housing is installed correctly. See page E-35.
Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is
insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move
the projector to a cooler location.
Use the COMPUTER, VIDEO or S-VIDEO button on the remote control or the SOURCE button on the cabinet to
select your source (Computer, Video or S-Video). See page E-19.
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page E-32.
Open the lens shutter. See page E-18.
Reset the settings or adjustments to factory preset levels using “Factory Default” in the menu. See page E-34.
Enter your registered keyword if the Security function is enabled. See page E-24.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver
or power management software.
If you accidentally hit the POWER button on the remote control, wait 60 seconds and then press the POWER
button again to resume.
Reposition the projector to improve its angle to the screen. See page E-19.
Use the Keystone correction function to correct the trapezoid distortion. See page E-20.
Adjust the focus. See page E-20.
Reposition the projector to improve its angle to the screen. See page E-19.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
E-11.
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Use the COMPUTER, VIDEO or S-VIDEO button on the remote control or the SOURCE button on the cabinet to
select the source you want to input. See page E-19.
Install new batteries. See page E-9.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page E-9.
See the Power/Status/Lamp Indicator on page E-37.
If Auto Adjust is off, turn it on or adjust the image manually with Horizontal / Vertical / Clock / Phase in the
menu. See page E-32.
Problem Check These Items
Common Problems & Solutions
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nec lt 170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nec lt 170 in the language / languages: English as an attachment in your email.

The manual is 1,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec lt 170

Nec lt 170 User Manual - German - 45 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info