Manual Nec GT 5000 (page 94 of 115) (English)

493541

Zoom out

Zoom in

1/115

8-25

Enable/Disable ........ This turns the Security function on or off.

Keyword .................. Enter an appropriate keyword when you

use the Security function.

(Up to 10 characters can be used.)

The Security function is available only

when your keyword is entered.

Use Protect key ....... Check this box to lock your projector

when using a PC card. To use a key-

word without a PC card, do not check

this box.

Drive ........................ Switches between PC Card slots.

Read ........................ Reads data of a PC card.

The Security function is not available un-

less at least one PC card is registered.

(if the “Use Protect key” check box is se-

lected)

Up to 5 PC cards can be registered.

Delete ...................... Deletes data of a registered PC card.

To set up a keyword to enable the Security function without

using a registered PC card.

NOTE: Only numbers can be entered when you use the remote control Source/

Input buttons.

1. Use the SELECT

̆̄

button to select “Keyword” and use the software

keyboard to enter a keyword.

NOTE: Please make a note of your keyword.

2. Use the SELECT

̆̄

button to select “Enable” and use the SELECT

̆̄

button to select “OK”, then the Security function will be enabled. An

“Are you sure?” message will appear. Use the SELECT

̇̈

button and

press the ENTER button.

The Security function takes effect.

Security

The Security function enables you to protect your projector so

that the projector will not project a signal unless you enter a key-

word. There is also an option to lock the projector by using a

registered PC card as a protect key. Once you have registered

your PC card as a protect key, you are required to insert the

registered PC card into the PC card slot of the projector each

time you turn on the projector. You can enable the Security func-

tion by using a keyword only.

To register a PC card as a protect key.

1. Insert a PC card into the PC card slot of the projector.

2. Use the SELECT

̆̄

button to select “Use Protect key” and press the

ENTER button. A check mark will be placed.

3. Use the SELECT

̆̄

button to select "Read" and press the ENTER

button.

Data of the PC card will be read into the projector.

4. Use the SELECT

̆̄

button to select "Register" and press the ENTER

button.

Downloaded data will be registered and be displayed in the list window.

5. Use the SELECT

̆̄

button to select "Keyword" and use the software

keyboard to enter a keyword.

NOTE: To use a PC card as a protect key, you must also set up a keyword. Please

make a note of your keyword.

This completes registration of your PC card.

To enable Security, use the SELECT ̆̄ button to select "En-

able" and use the SELECT ̆̄ button to select "OK" and "Secu-

rity function will be enabled. An “Are you sure?" message will

appear. Use the SELECT ̇̈ button and press the ENTER but-

ton.

The Security function takes effect.

To turn on the projector when Security is enabled (when

using your keyword only).

NOTE: Only numbers can be entered when you use the remote control Source/

Input buttons.

1. Press and hold the POWER button for a minimum of two seconds.

The projector will be turned on and display a message to the effect that

the projector is security-protected.

2. Select [Projector Options]

→

[Security] from the menu and press the

ENTER button.

The Release Code input screen will be displayed.

3. Enter your keyword in the Release Code input screen.

You can view the projected image.

NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or

your dealer will provide you with your Release Code. See more information at

the end of this section.

To turn on the projector when Security is enabled (when

using a PC card as a protect key).

NOTE: The projector does not support FAT32 or NTFS formatted flash memory

card or USB memory device.

Be sure to use a flash memory card or USB memory device formatted with the

FAT16 or FAT file system.

To format your flash memory card or USB memory device in your computer, refer

to the document or help file that comes with your Windows.

1. Insert your registered PC card into the PC card slot.

2. Press and hold the POWER button for a minimum of two seconds.

The projector will turn on and then recognize the PC card. Once the

image has been projected, it will stay on without the PC card.

• The security disable mode is maintained until the main power is turned

off (by setting the main power switch to "O" or unplugging the power

cable).

In the following cases you will be asked to check the protect key or

input the keyword:

(1) When "OK" is selected at an image for which security is set and

the power is turned off then back on

(2) When the main power is turned off then back on while the security

function is enabled

8. Using On-Screen Menu

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nec GT 5000 in the language / languages: English as an attachment in your email.

The manual is 4,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nec GT 5000

Nec GT 5000 User Manual - German - 115 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nec GT 5000 Manual

Product: